Advertisement
FAQ
常見問題解答
Why does the humidity indication remain
unchanged?
濕度指示燈為什麼不變？
The indicator
濕度指示燈
The product may not sense the humidity
properly depending on the setting place.
Change the setting place. (P.6 ~ 7)
放置場所不同，存在無法正確感知濕度的情況。
改變放置場所。(第6 ~ 7頁)
The indicator
濕度指示燈
The room size is too large for the
product?
Refer to the applicable room size.
(P.27)
房間的大小是否過大？
請參考適用面積。(第27頁)
Notice 提示事項
Please use the humidify sign only as a
reference.
請將濕度指示作為參考。
It is different from the display of the
household hygrometer sometimes.
有時與家庭用濕度計的顯示值不同。
The humidity value will vary with the
temperature.
根據溫度的變化，濕度值會產生變化。
The humidity may also vary with the
airflow condition.
空氣流通情況不同，濕度也會不同。
TROUBLESHOOTING
故障排除
If a problem is encountered, please investigate it by going through the following items.
If the problem still persists, please disconnect the power plug and contact the dealer for repair.
首先請確認以下內容，如果仍無法修復，請拔出電源插頭，聯繫經銷商進行維修。
Possible situation
可能發生的狀況
Clean sign remains red
1
even when the operation
continues.
即使是持續運轉，空氣污
染度指示燈一直為"紅色"
24
(humidity indicator)
(濕度指示燈)
is always on.
一直亮起。
is always on.
一直亮起。
The indicator may turn red when the product is subject to
steam in the bathroom or vapor emitting from sprayers.
受到浴室等熱氣、噴霧產生的氣體影響，指示燈可能會變紅。
Why is a "jee" sound from the
emission outlet.
為什麼出風口發出"嘰"的聲音？
There is a slight sound when nanoe
is being generated. Depends on the
environment and operation mode,
the sound may be a bit loud or
inaudible but it is not abnormal.
產生nanoe
用環境、運轉模式不同，聲音的大小有所不
同，這並非異常。
Why is there dewing on the window
and wall?
窗戶以及牆壁為什麼會結露？
Even if the humidity in the room is
moderate, there may be dewing on
a cold window or wall.
即使房間濕度適中，在溫度較低的窗戶以及
牆壁等上也會發生結露。
Why does the clean sign remain
unchanged?
為什麼空氣污染度指示燈不發生變化？
Such problems are easy to occur when
the sensitivity of the sensor is higher or
lower. You can adjust the sensor with a
specified sensitivity. (P.22)
感應器靈敏度較高或較低時容易出現此現象。
可調節感應器靈敏度。（第22頁）
How to turn off the clean sign?
怎麼關閉空氣污染度指示燈？
Please press
for about 3 seconds at the same time
during operation.
在運轉過程中同時按下
按鈕約3秒鐘。
To make the clean sign light on again,
Please press the buttons for about 3
seconds again.
再次按此按鈕約3秒，空氣污染度指示燈重新
亮起。
Please confirm the following
請確認以下內容
時，將發出些許聲音。根據使
®
and
和
®
buttons
Advertisement
