Related Manuals for Cytron SK1632
Summary of Contents for Cytron SK1632
- Page 1 ROBOT . HEAD to TOE P roduct User’s Manual – SK1632 SK1632 16-bit or 32-bit PIC Start-Up Kit User's Manual V1.2 Oct 2015 Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved...
-
Page 2: Table Of Contents
ROBOT . HEAD to TOE P roduct User’s Manual – SK1632 INDEX Introduction/Overview Packing List Product Specification And Limitations Dimension Board Layout Hardware Software Getting Started Warranty Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved... -
Page 3: Introduction/Overview
1. INTRODUCTION/OVERVIEW SK1632 is new starter kit designed for 28 pin PIC which support all 5V operate 16-bit and 32-bit PDIP PIC microcontroller. This board comes with basic electronic components for user to begin project development. It offer plug and use features: ●... -
Page 4: Packing List
Please check the parts and components according to the packing list. If there are any parts missing, please contact us at s ales@cytron.com.my immediately. 1. 1 x SK1632 board 2. 1 x 8MHz Crystal 3. 2 x header pin 15 ways Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved... -
Page 5: Product Specification And Limitations
PIC24HJ32GP202 dsPIC33EP512MC202 dsPIC33FJ32GP202 PIC24HJ128GP502 dsPIC33EP32MC502 dsPIC33FJ32MC202 PIC24HJ128GP202 dsPIC33EP64MC502 dsPIC33FJ128GP802 PIC24HJ64GP502 dsPIC33EP128MC502 dsPIC33FJ64GP802 PIC24HJ64GP202 dsPIC33EP256MC502 dsPIC33FJ128GP202 PIC24HJ32GP302 dsPIC33EP512MC502 dsPIC33FJ64GP202 *** PIC with some of the pin name is different from others. Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved... -
Page 6: Dimension
*** SK1632 was tested with PIC32MX250F128B and dsPIC33fj64GP802 o nly. The rest of the PIC listed on the table above may work with SK1632 as the power pin is match. LCD Pins - 4-bits mode PIC Pin Pinguino Pin Name... - Page 7 ROBOT . HEAD to TOE P roduct User’s Manual – SK1632 Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved...
-
Page 8: Board Layout
2x5 female header and Straight Pin Header is needed. This is optional to user. 4. Header pin, extension from PIC microcontroller pin PIC Microcontroller pins extension and is reserved for header pin. User may extend SK1632 to breadboard or donut board with header pins provided. - Page 9 7 to 15VDC. 12. Micro USB connector Using for connection using USB cable between SK1632 to a USB host controller (usually personal computer). This function is only valid for certain model of PIC microcontroller. Please refer PIC supported for 16-bits and 32-bits.
- Page 10 P roduct User’s Manual – SK1632 LCD Selectable pad By default, the LCD backlight is selected. If user don't want to use LCD backlight (B/L), user may simply cut through the wire connection for LCD. Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved...
-
Page 11: Hardware
Hex code sometime called machine code. It is result after compilation. 1. Connect PICkit programmer shown as figure below. Figure below is using PICkit 3 from Microchip to load program into SK1632. Make sure the arrow at PICkit pin of SK1632 is same side with arrow at PICkit 3 programmer. - Page 12 header h eader pin are not included in SK1632 packing list. User need to get it separately. 1. To use LCD, cut S traight Pin Header (Male) 2x40 Ways to 2x8 ways. Solder the header pin to the LCD shown as figure below.
- Page 13 ROBOT . HEAD to TOE P roduct User’s Manual – SK1632 3. Preset/Potentiometer is used to adjust the contrast of LCD display. Turn left or right to adjust the contrast. Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved...
- Page 14 USB is one of possible serial communication between microcontroller and computer offered on SK1632. Again this is optional to user. USB data pins (pin 22 (D-) and pin 21(D+)) are connected to a micro USB socket on SK1632 for USB development usage. Microchip has 4 USB 16-bit microcontrollers in 28-pin PDIP package (as the time this manual is written) which include PIC24FJ32GB002, PIC24FJ64GB002, PIC24FJ64GB202 and PIC24FJ128GB202.
-
Page 15: Software
ROBOT . HEAD to TOE P roduct User’s Manual – SK1632 7. SOFTWARE To get started with SK1632, users may use MPLAB X or Pinguino IDE software. Download and from MPLAB X IDE installer P inguino IDE software... -
Page 16: Getting Started
5. Click “Make and Program Device Project” . Make sure this project hex file is burn using PICKit3. 6. In case of error appear, go to “Project Properties” > “PicKit3” > “Power” and tick the box. Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved... - Page 17 P roduct User’s Manual – SK1632 Note: SK1632 cannot be powered from pickit/ICSP pin as the VDD is not connected. It must be powered from either the on board USB micro B receptor or from DC jack. Get Started with Pinguino IDE for LED Blinking 1.
- Page 18 P roduct User’s Manual – SK1632 4. Click on the “New File” icon, go to Basic > Blink > Blink.pde. 5. Once done, click “Compile” and upload to SK1632. Upload the code using USB cable. NOTE: I n order to upload program, make sure the ...
- Page 19 P roduct User’s Manual – SK1632 Steps to Enter Bootloader Mode STEP RESET SW1(A1) Press and Hold Release Press and Hold Press and Hold Release Press and Hold Release Release Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved...
-
Page 20: Warranty
No. 16, Jalan Industri Ringan Permatang Tinggi 2, Kawasan Industri Ringan Permatang Tinggi, 14100 Simpang Ampat, Penang, Malaysia. Tel: +604 - 504 1878 Fax: +604 - 504 0138 URL: www.cytron.com.my Email: s upport@cytron.com.my sales@cytron.com.my Created by Cytron Technologies Sdn. Bhd. – All Rights Reserved...
Need help?
Do you have a question about the SK1632 and is the answer not in the manual?
Questions and answers