Advertisement
USER'S GUIDE
N-GxX-xx-01 (standard)
N-GxX-xx-01(L) (low profile)
The N-GxX-xx-01(x) gigabit ethernet Network
Interface Card (NIC) provides a 1000Base-
SX/LX fiber port to deliver fiber optic
connectivity to the desktop in fiber-rich LAN
environments. With both standard and low
profile form factors, driver support for most
popular operating systems, and supports 32/64-
bit PCI 2.2 plug-and-play capability, all help
make installation a breeze in virtually any PC on the Network.
Part Number
Port One - Duplex Fiber-Optic 1000Base-SX/LX
N-GSX-SC-01
SC, 850 nm multimode, [62.5/125µm: 220 m (722 ft)]
N-GSX-SC-01(L)
[50/125µm: 550 m (1804 ft)*]
N-GSX-SC-01-020**
SC, 850 nm multimode, [62.5/125µm: 220 m (722 ft)]
N-GSX-SC-01(L)-020**
[50/125µm: 550 m (1804 ft)*]
N-GSX-LC-01
LC, 850 nm multimode, [62.5/125µm: 220 m (722 ft)]
N-GSX-LC-01(L)
[50/125µm: 550 m (1804 ft)*]
N-GSX-LC-01-020**
LC, 850 nm multimode, [62.5/125µm: 220 m (722 ft)]
N-GSX-LC-01(L)-020**
[50/125µm: 550 m (1804 ft)*]
N-GLX-SC-01
SC, 1310 nm single mode, 10 km (6.2 miles)*
N-GLX-SC-01(L)
N-GLX-LC-01
SC, 1310 nm single mode, 10 km (6.2 miles)*
N-GLX-LC-01(L)
Optional accessories sold separately
Part Number
Description
BTR-NGX-PXE
PXE, Bootable ROM Chip
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network installation.
**The -020 designation at the end of the part number means sold in packs of 20
NICs only. There are no changes to NIC specifications.
Installation and Configuration . . .2
Cable Specifications . . . . . . . . . . .4
Technical Specifications . . . . . . . .5
Troubleshooting . . . . . . . . . . . . . .6
Contact Us . . . . . . . . . . . . . . . . . .7
Advertisement
Table of Contents
Related Manuals for Transition Networks N-GXX-XX-01
Summary of Contents for Transition Networks N-GXX-XX-01
- Page 1 USER’S GUIDE N-GxX-xx-01 (standard) N-GxX-xx-01(L) (low profile) The N-GxX-xx-01(x) gigabit ethernet Network Interface Card (NIC) provides a 1000Base- SX/LX fiber port to deliver fiber optic connectivity to the desktop in fiber-rich LAN environments. With both standard and low profile form factors, driver support for most popular operating systems, and supports 32/64- bit PCI 2.2 plug-and-play capability, all help...
-
Page 2: Installation And Configuration Checklist
Ensure that the PCI machine supports master slots, and INT multiple sharing and timing functionality. • DO NOT install N-GxX-xx-01(x) NICs in PCI slave slots. Please refer to your PC system manual and select the appropriate configuration settings. • When installing multiple N-GxX-xx-01(x) NICs at the server station, you should correctly configure the IRQ settings of the PCI slot. -
Page 3: Cable Specifications
The fiber optic transmitters on the device meet Class I Laser safety requirements per IEC-825/CDRH standard and comply with 21CRF1040.10 and 21CRF1040.11. Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours Technical Specifications For models N-GxX-xx-01 and N-GxX-xx-01(L) Standards: Expansion bus standard: Data rate LED: max: -4.0 dBm... -
Page 4: Troubleshooting
ROM socket. See Figure 1 on page 2. After power UP, the LINK/ACT LED should light; if not, check the following: Confirm that the N-GxX-xx-01(x) NIC is properly inserted into the master slot. Confirm that the PC is properly connected to a power source and with the power source turned ON. -
Page 5: Compliance Information
All registered trademarks and trademarks are the property of their respective owners. Copyright restrictions © 2004-2005 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means—graphic, electronic or mechanical—without written permission from Transition Networks Printed in the U.S.A.
Need help?
Do you have a question about the N-GXX-XX-01 and is the answer not in the manual?
Questions and answers