1. Manuals
  2. Brands
  3. Transition Networks Manuals
  4. Media Converter
  5. CSRFB10XX-100
  6. User manual

Transition Networks CSRFB10XX-100 User Manual

Csrfb10xx-100 series slide-in-module media converter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
User's Guide
CSRFB10xx-100
Slide-in-Module Media Converter
•
•
•
The CSRFB10xx-100, 2-port Ethernet/Fast Ethernet
bridging media converter is designed to be installed in
a Transition Networks PointSystem™ chassis. This
converter connects 10Base-T Ethernet or 100Base-TX
Fast Ethernet twisted-pair copper network converters
to network converters on a 100Base-FX Fast Ethernet fiber network. The CSRFB
includes a status reporting feature for viewing operational parameters only from its
remotely attached CSRFB converter via the fiber connection.
Part Number
Port One - Copper
10Base-T/100Base-TX
RJ-45
CSRFB1011-100
100 m (328 ft)*
RJ-45
CSRFB1013-100
100 m (328 ft)*
RJ-45
CSRFB1014-100
100 m (328 ft)*
RJ-45
CSRFB1040-100
100 m (328 ft)*
RJ-45
CSRFB1029-100
100 m (328 ft)*
RJ-45
CSRFB1029-101
100 m (328 ft)*
RJ-45
CSRFB1029-102
100 m (328 ft)*
RJ-45
CSRFB1029-103
100 m (328 ft)*
Install CSRFB1029-100/101 and CSRFB1029-102/103 single-
fiber optic in the same network where one is the local (center)
converter and the other is the remote (terminal) converter.
Copper to Fiber
10/100 Bridging (2-Port)
10Base-T/100Base-TX to 100Base-FX
Port Two - Duplex Fiber-Optic
100Base-FX
ST, 1310nm multimode
2 km (1.2 miles)*
SC, 1310 nm multimode
2 km (1.2 miles)
SC, 1310 nm single mode
20 km (12.4 miles)
SFP Empty Slot
SC, 1310nmTX/1550nmRX
20km (12.4 miles)
SC, 1550nmTX/1310nmRX
20km (12.4 miles)
SC, 1310nmTX/1550nmRX
40km (24.9 miles)
SC, 1550nmTX/1310nmRX
40km (24.9 miles)
Installation . . . . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . . . .7
Cable Specifications . . . . . . . . . . . . .11
Technical Specifications . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . .13
Contact Us . . . . . . . . . . . . . . . . . . .15
Compliance Information . . . . . . . . .16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CSRFB10XX-100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Transition Networks CSRFB10XX-100

Summary of Contents for Transition Networks CSRFB10XX-100

  • Page 1 • 10/100 Bridging (2-Port) • 10Base-T/100Base-TX to 100Base-FX The CSRFB10xx-100, 2-port Ethernet/Fast Ethernet bridging media converter is designed to be installed in a Transition Networks PointSystem™ chassis. This converter connects 10Base-T Ethernet or 100Base-TX Fast Ethernet twisted-pair copper network converters to network converters on a 100Base-FX Fast Ethernet fiber network.

  • Page 2: Installation

    CSRFB10xx-100 Installation CAUTION: Wear a grounding converter and observe electrostatic discharge precautions while handling the media converter. Failure to observe this caution could result in damage to or failure of the media converter. Typical system configuration Network Chassis Fiber Cable Chassis Center Converter SW6 set to ‘Center’...

  • Page 3: Install The Slide-In-Module

    MUST be installed at EACH twisted-pair copper link. Note: Factory default is “A” enabled. Transition Networks recommends leaving the converter in the “A” enabled position. The Loopback Mode jumper is located on the media converter’s circuit board (labeled ALL= all frames...

  • Page 4: Operation

    100Base-FX fiber cable with male, ™ two-stranded TX to RX connectors installed at both ends. Connect the fiber cables to the CSRFB10xx-100 media converter as described: • Connect the male TX cable connector to the female TX connector. •...

  • Page 5: Half Duplex Network (512-Bit Rule)

    Auto-Negotiation The Auto-Negotiation feature allows the CSRFB10xx-100 media converter to automatically configure itself to achieve the best possible mode of operation over a link. The media converter will broadcast its speed (10Mbps or 100Mbps) and duplex capabilities (full or half) to the other converters and negotiates the best mode of operation.

  • Page 6: Bandwidth Allocation

    CSRFB10xx-100 Operation -- Continued Product features - continued Bandwidth allocation Bandwidth allocation feature is available on the Center located SRFB converter only. The center converter supports independent ingress rate limiting on both the copper and fiber ports. The increments range from 64kps up to full bandwidth. This...

  • Page 7: Technical Specifications

    The information in this user’s guide is subject to change. For the most up-to-date information on the CSRFB10xx-100 media converter, view the user’s guide on-line at: www.transition.com. Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.
  • Page 8 CSRFB1029-10, CSRFB1029-102, CSRFB1029-103, CSRFB1040-100 Regulation: EMC Directive 89/336/EEC Purpose: To declare that the CSRFB10xx-100 to which this declaration refers is in conformity with the following standards. EMC-CISPR 22:1985 Class A; EN 55022:1998 Class A; FCC Part 15 subpart B; 22 CFR...

  • Page 9: Compliance Information

    Konformität. In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, Transition Networks will accept post usage returns of this product for proper disposal. The contact information for this activity can be found in the 'Contact Us' portion of this document.

This manual is also suitable for:

Csrfb1011-100Csrfb1013-100Csrfb1014-100Csrfb1029-100Csrfb1029-10Csrfb1029-102 ... Show all

Table of Contents