Download  Print this page

Transition Networks SMACF10XX Quick Start Manual

Management aggregation converter
Hide thumbs
   

Advertisement

SMACF10xx Management Aggregation Converter

QUICK START GUIDE

Install SMACF10xx in Network
1.
Unpack and Install SMACF10xx Units
on table or other flat, stable surface in well-ventilated area.
2.
Power On SMACF10xx Units Install power adapter cord at back
of each SMACF10xx unit. Connect power adapter plug to AC
power. Verify power by observing illuminated LEDs.
3.
Connect SMACF10xx Units to Ethernet
to Ethernet
segment. Use Category 5 twisted-pair cable and
appropriate fiber cable to connect SMACF10xx Management Unit
through any port (optionally through a hub or switch) to the
Ethernet
segment. Connect AT LEAST ONE port on EACH
installed SMACF10xx Reporting Unit (optionally through a hub or
switch) to the same Ethernet
Main Management Unit
MM or SM Fiber
CAT 5
In-Band Management
VLAN Segmentation
LAN Switch
10 or 100 Mb/s Speed Selection
CAT 5
SNMP Management
of Both Main Management
and Reporting Units
Network managed by SMACF10xx Management Unit.
Place SMACF10xx units
Network
Locate path
segment.
Reporting Unit
CAT 5
CAT 5
Corporate
Management
Remotely
Managed
Converters
Manufacturing
& Logistics
SNMP Management
of all Remote Reporting Units
Network managed by CPSMM-xxx PointSystem
Module connected to switch on same segment as Reporting Units.
Configure Main Management Unit or Management Module
Installed in Chassis
NOTE: The SMAC10xx Management Unit contains both a Management
Unit and a Reporting Unit. Each must be configured separately.
4.
Connect Management Unit or Management Module to Terminal
Locate null modem DB-9 serial port cable with female DB-9
connector. Attach DB-9 serial port female cable connector to
DB-9 serial port male connector on SMACF10xx Management
Unit OR on CPSMM-xxx PointSystem
installed in Media Conversion Center. Attach other end of DB-9
serial port cable to ASCII terminal or terminal emulator.
5.
Verify Terminal Settings
Baud/ 8 data bits/ 1 stop bit/ no parity. If necessary, use methods
appropriate to terminal to modify settings.
Bring up Management Unit Interface at Terminal (SMACF10xx
6.
Management Unit ONLY) First set switch at back of SMACF10xx
Management Unit to UP position. (SMACF10xx Management
Unit and CPSMM-xxx PointSystem
<enter> at terminal keyboard to bring up command-line prompt.
7.
Enter superuser Mode At command-line prompt, type and enter
the su command, using the case-sensitive Transition Networks
default password private .
CPSMM100> SU=private
2
Technical
Accounting
Publications
Sales & Marketing
MM or SM Fiber
PointSystem
Modular Chassis
Copper Switch
Management
Management Module
Default terminal settings are 9600
Management Module) Press

Advertisement

Table of Contents
loading

  Related Manuals for Transition Networks SMACF10XX

  Summary of Contents for Transition Networks SMACF10XX

  • Page 1: Quick Start Guide

    Unpack and Install SMACF10xx Units on table or other flat, stable surface in well-ventilated area. Power On SMACF10xx Units Install power adapter cord at back of each SMACF10xx unit. Connect power adapter plug to AC power. Verify power by observing illuminated LEDs.
  • Page 2 Repeat steps 11-14 for all installed SMACF10xx Reporting Units. Manage SMACF10xx Units at Web Interface At the superuser A display showing available SMACF10xx units comes up. Refer to on- line help available from the display for detailed direction for managing the SMACF10xx units.

This manual is also suitable for:

Smacf10 series