Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Package contents The following contents should be found in your box: One TD-8811/TD-8811B External ADSL2+ ROUTER One AC power Adapter for TD-8811/8811B External ADSL2+ ROUTER One Resource CD for TD-8811/TD-8811B External ADSL2+ ROUTER, including: • This User Guide • Quick installation Guide Program •...
10M/100M Ethernet devices, support Auto-MDI/MDIX. The TD-8811/TD-8811B not only uses html (web mode through Ethernet port) to configure the router but also uses external utility software, too. You can download it from our website (http://www.tp-link.com).
1.3 Transmit data-rate Max download data-rate: 24Mbps Max upload data-rate: 1Mbps Max line length: 6Km 1.4 ATM property AAL0, AAL5, OAM, RM, and raw cell types supported Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in software Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) 1.5 System support...
Chapter 2. Hardware Installation Guide The TD-8811/TD-8811B maintains three separate interfaces, one Ethernet, one USB interface and one ADSL interface. The Router should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be safely connected to the various devices as well as to a power source.
2.4 Hardware installation procedures The procedure to install the Router can be described in the following steps: First Step: Connect the MODEM port of Splitter with the LINE port of the TD-8811/TD-8811B ADSL2+ ROUTER by telephone line. Second Step: Connect category 5 cable with RJ45 jacks to ADSL2+ Router’s LAN port and your computer’s NIC.
Chapter 3. System Configuration 3.1 Computer Configuration Connect the cable according to Chapter 2, turn on the power. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Network mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).
Note: Users of Windows 98 can open TCP/IP Properties according to the following: Right-click (Mouse) Network Neighbor -> Choose Properties -> Double-click TCP/IP PCI Fast Ethernet Adapter. The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor ->Choose Properties->Right-press Local Connection ->Choose Properties->Double- click Internet Protocol (TCP/IP).
If the screen looks like the following, the connection fails. Repeat the previous steps again. 3.2 Login Startup Internet Explorer, and enter 192.168.1.1, then enter default user name(admin) 、 password(admin), When ADSL2+ connection is OK, you will see the Figure 3-4. TD-8811/8811B External ADSL2+ ROUTER Figure 3-2...
You will then see the Figure 3-5. This screen displays some information about the device such as link rate. Default user name and password both are “admin”; if you want to change them, please go to TD-8811/8811B External ADSL2+ ROUTER Figure 3-4 Figure 3-5...
“Management” “Access control” “Passwords”. (Figure 3-6) 3.3 Web Setup Choose “Advanced Setup” ”WAN”, you will enter the page of Wide Area Network (WAN) Setup, you will see the Figure 3-7. There are 7 PVC links in the WAN setup page, choose the right PVC according to your needs, and then click the edit button, you will enter the page of ATM PVC Configuration (See Figure 3-8).
Enter VPI/VCI value and service category which is provided by your ISP, click next to enter the next step. You will see the Figure 3-9. Note: The type of network protocol selected may be different in different areas, there are five types （Figure 3-9）, so you should ask your ISP to acquire the local type of network protocol and Encapsulation mode.
TD-8811/8811B External ADSL2+ ROUTER of user name and password which is provided by your ISP, after selecting other functions (often using the default setup), click the next button. Figure 3-10 After that, the Figure 3-11 will appear. Turn on the selected functions according to your demands. Clicking the next button to enter the next step, you will see the Figure 3-12, finally click save to complete the configuration.
PPP over Ethernet (PPPoE) If you select the protocol of PPP over Ethernet (PPPoE), you will see the Figure 3-13, enter the value of user name and password which is provided by your ISP, after selecting other functions (often using the default setup), click the next button. You will see the Figure 3-14.
MAC Encapsulation Routing (MER) If you select the protocol of MAC Encapsulation Routing (MER), you will see the page (Figure 3-16). Enter the parameter and the way which is provided by your ISP, then click the next button. TD-8811/8811B External ADSL2+ ROUTER Figure 3-14 Figure 3-15...
After that, Figure 3-17 will be available. You can select the functions according to your needs. Clicking the next button to enter the next step, you will see the Figure 3-18, finally click save to complete the configuration. TD-8811/8811B External ADSL2+ ROUTER Figure 3-16 Figure 3-17...
IP over ATM (IPoA) If you select the protocol of IP over ATM (IPoA), the Figure 3-19 will display, enter the parameter and the way which is provided by your ISP, then click the next button. You will see the page (Figure 3-20), then turn on the selected functions according to your needs. Clicking the next button to enter the next step, you will see the Figure 3-21, finally click save to complete the configuration.
Bridging If you select the Bridging protocol, you just open the bridge service function options, you will see the Figure 3-22, then click the next button, you will see the Figure 3-23, press save to complete the configuration finally. TD-8811/8811B External ADSL2+ ROUTER Figure 3-20 Figure 3-21...
Note: After you complete the settings, the new settings must be saved and the Router must be restarted for the settings to take effect. Please press the Save/Reboot button on the Figure 3-24 to restart. TD-8811/8811B External ADSL2+ ROUTER Figure 3-22 Figure 3-23...
All of the above setting is under windows XP OS. 3.4 Software Dial If TD-8811/TD-8811B CPE work in bridged (RFC 1483 Bridged) mode when it connects Internet. You must install dial software on your PC. There are some software working on Windows in market, example for EnterNet3000, RASPPPoE and WinPeET.
3.5 USB Configuration If you use the USB interface, First, you must install the USB’s drive to the computer. You can obtain the drives from the provided CD or download from our website. (http://www.tp-link.com) USB Drive installation procedures If the hardware is installed before the computer is Power On. Please turn on the computer and enter the operating system, Then the operating system will identify the device.
Select the ‘search removable media(floppy, CD-ROM…)’ and click the next button, then Figure 3-27 is available. The driver will be searched and installed. Note: You must insert the CD first. TD-8811/8811B External ADSL2+ ROUTER Figure 3-26 Figure 3-27...
After that, you will see the Figure 3-28. The installation completes, click Finish to close the installation. Please refer to chapter 3.1 to finish the IP configuration for USB connect. Then you could use the USB device. Note: All of the above settings are under windows XP. If you want to pull out the USB device you must disconnect the network of USB first.
Configure the DNS parameters Configure RIP(Routing Information Protocol） Configure IP route Configure Security rule Configure DSL parameter Note: If you want to acquire further details, please access our website (www.tp-link.com) and consult the User Guide of TD-8811/TD-8811B. TD-8811/8811B External ADSL2+ ROUTER...
Appendix A: FQA What related parameters are required to acquire ISP when you want to access the internet by ADSL2+ ROUTER? 1) Dial user: Connection protocol, User name, Password, Value of VPI/VCI, Encapsulation mode of AAL5 and so on. 2) Static IP user: Connection protocol, WAN IP Address, Subnet Mask, Gateway, Value of VPI/VCI, Encapsulation mode of AAL5 and so on.
TD-8811/8811B External ADSL2+ ROUTER Appendix C: Contact Information For more help with the installation or operation of the TP-LINK TD-8811/TD-8811B External ADSL2+ ROUTER, please contact us. Website: http://www.tp-link.com...