MICRO CAMERA HEAD
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided
if you make changes or modifications not expressly approved by the party responsible for compliance
to Part 15 of the FCC rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
CAUTIONS ON USE
Please use this apparatus by connecting only with camera control unit IK-CU44A.
Read the "CAUTIONS ON USE AND INSTALLATION" in the instruction manual of IK-CU44A, and follow
(1) Camera head (without lens) .............................................................................. 1
(a) Camera holder ............................................................................................. 1
(b) Instruction manual ....................................................................................... 1
TOSHIBA CCD CAMERA
Promptly register your product with Toshiba on-line at www.toshiba.com/taisisd. By registering your prod-
uct you will be eligible for periodic updates, announcements, and special offers. You will have access to extended
warranty options, upgrades (as applicable), useful tips, on-line troubleshooting, and the ability to schedule ser-
vice on-line if necessary. The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD")
makes the following limited warranties. These limited warranties extend to the Original End-User ("Your[r]").
Limited One (1) Year Warranty of Labor and Parts
ISD warrants this product and parts against defects in material or workmanship for a period of one year from the
date of original retail purchase by the end-user. During this period, ISD will repair or replace a defective product or
part with a new or refurbished item. The user must deliver the entire product to an ISD authorized service center.
The user is responsible for all transportation and insurance charges for the product to the Service Center. ISD
reserves the right to substitute Factory Refurbished Parts and / or Factory Refurbished Product in place of those
in need of repair.
Step-by-step Procedures - How to Obtain Warranty Service
 Verify operation of the unit by checking the instruction manual
 If there is a defect in material or workmanship, contact an Authorized Service Provider within 30 days after the
product fails to comply with specifications.
 Arrange for delivery of the product to the ISD authorized service center. Products must be insured and se-
curely packed, preferably in the original shipping carton. A letter explaining the defect and a copy of the bill of sale
or other proof of purchase must be enclosed with a complete return street address and daytime telephone num-
ber. Charges for transportation and insurance must be prepaid by the end-user.
Questions? If you have any questions, please check the Toshiba Imaging Systems Division Web site
Your Responsibility, warranties are subject to the following conditions:
 You must retain the bill of sale or provide other proof of purchase.
 You must schedule service within thirty days after you discover a defective product or part.
 All warranty servicing of this product must be made by a Toshiba ISD Authorized Service Provider.
 The warranty extends to defects in material or workmanship as limited above, and not to any products or parts
that have been lost or discarded by user. The warranty does not cover damage caused by misuse, accident,
improper installation, improper maintenance, or use in violation of instructions furnished by ISD. The warranty
does not extend to units which have been altered or modified without authorization of ISD, or to damage to
products or parts thereof which have had the serial number removed, altered defaced or rendered illegible.
ALL WARRANTIES IMPLIED BY STATE LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF
THE LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply. WITH THE EXCEPTION OF ANY WARRAN-
TIES IMPLIED BY STATE LAW AS HEREBY LIMITED, THE FOREGOING EXPRESS WARRANTY IS EXCLU-
SIVE AND IN LIEU OF ALL OTHER WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PROD-
UCTS OR PARTS. IN NO EVENT SHALL ISD BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAM-
AGES. Some states do not allow the exclusion or limitation of incidental or consequential damages so
the above limitation may not apply.
No person, agent, distributor, dealer, service station or company is authorized to change, modify or ex-
tend the terms of these warranties in any manner whatsoever. The time within which an action must be
commenced to enforce any obligation of ISD arising under this warranty or under any statute, or law of
the United States or any state thereof, is hereby limited to one year from the date you discover or should
have discovered, the defect. This limitation does not apply to implied warranties arising under state law.
Some states do not permit limitation of the time within which you may bring an action beyond the limits
provided by state law so the above provision may not apply to user. This warranty gives the user specific
legal rights, and user may also have other rights, which may vary from state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division
Copyright © 2002 Toshiba America, Inc. All rights reserved.
When connecting or discon-
necting the camera cables
Camera control unit
(for the camera head and
camera control unit), always
turn off the power switch of
the camera control unit first.
If not, the camera head may
DC IN 12V
1/3 inch IT-CCD
Horizontal: 768 pixels, Vertical: 494 pixels
Effective image area
Horizontal: 4.88 mm, Vertical: 3.66 mm
Horizontal: More than 470 lines, Vertical: More than 350 lines
Standard intensity of
40 lx (F1.6, 3000K)
illumination for objects
Minimum intensity of
3.5 lx (F1.6, 3000K)
illumination for objects
0.32 oz (9g)
Design and specifications are subject to change without notice.
For further details, contact your camera dealer.
Camera control unit
Focal length mm
(in air 7.2)
CCD image plane
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the user in
any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether intentional or
accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including but not
limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by an
unauthorized third party.
6. Notwithstanding the foregoing, Toshiba's liabilities shall not, in any circumstances, exceed the purchase
price of the product.
COPYRIGHT AND RIGHT OF PORTRAIT
There may be a conflict with the Copyright Law and other laws when a customer uses, displays, distributes,
or exhibits an image picked up by a television camera without permission from the copyright holder. Please
also note that transfer of an image or file covered by copyright is restricted to use within the scope permitted
by the Copyright Law.
CAUTIONS ON USE AND INSTALLATION
Carefully handle the units.
Do not drop, or give a strong shock or vibration to the camera. This may cause problems. Treat the camera
cables carefully to prevent cable problems, such as cable breakdown and loosened connections.
Do not shoot intense light.
If there is an intense light at a location on the screen such as a spot light, a blooming and smearing may
occur. When intense light enters, vertical stripes may appear on the screen. This is not a malfunction. Ghosts
may occur when there is an intense light near the object. In this case, change the shooting angle.
Install the camera in a location free from noise.
If the camera or the cables are located near power utility lines or a TV, etc. undesirable noise may appear on
the screen. In such a case, try to change the location of the camera or the cable wiring.
When thin stripe patterns are shot, stripe patterns that are not actually there (moire) may appears as interfer-
ence stripes. This is not a malfunction.
Operating ambient temperature and humidity.
Do not use the camera in places where temperature and humidity exceed the specifications. Picture quality
will lower and internal parts may be damaged.
Be particularly careful when using in places exposed to direct sunlight. When shooting in hot places, de-
pending on the conditions of the object and the camera (for example when the gain is increased), noise in the
form of vertical strips or white dots may occur. This is not a malfunction.
Handling of the protection cap.
Keep the protection cap away from children. Children may put them into mouth or swallow them accidentally.
The protection cap protects the image sensing plane when the lens is removed from the camera, do not
When not using the camera for a longtime.
Stop supplying power.
When cleaning the camera
Always turn off the power and clean with a piece of soft dry cloth. Do not use benzine, alcohol, thinner,
household detergents, chemically treated cloths, etc. If used, coating and printed letters may be discolored.
When cleaning the lens, use a lens cleaning paper, etc.
Avoid using or storing the camera in the following places:
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places contacting chemicals (such as pesticides), rubber or vinyl products for a long period of time.
Nominal length m
EXC-4354 is not applicable for this model.
Unit : mm [inch]
ø : diameter
Ø 3 hloe
Tri-pot screw (1/4-20UNC)