Download Print this page

Trouble Indications; Before Calling Service Personal - Toshiba TLP-S200 Owner's Manual

3lcd data projector (xga / svga / high brightness / with pc card slot & document camera)
Hide thumbs

Advertisement

Trouble indications

The indicator lights inform you of internal abnormalities.
FAN
TEMP
LAMP
ON
No power
⇒ Problem with projector
(Off)
or
(Red lit)
• Unplug the power cord, and contact your dealer.
Lamp went out during use, or won't come on
FAN
TEMP
LAMP
ON
⇒ Returns to standby after about 2 minutes. If the projector fails to
(Red lit) (Red lit)
operate normally after turning the power back on, either the lamp
needs replacing, or there is a problem with the projector.
• If a lamp burns out, replace it with a new one.
• Unplug the power cord, and contact your dealer.
Power went out during use, or power won't come on
FAN
TEMP
LAMP
ON
⇒ Internal overheating, or the outside temperature is too high.
(Green lit) (Red lit)
(Red lit)
• Place the projector so that the air intake and exhaust are not
Or
Or
blocked.
(Orange lit)
(Off)
• Unplug the power cord and wait for a short while, then turn the
Or
power back on.
(Green lit)
• Clean the air filter.
❈ The
icon will appear before the power goes out.
❈ After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power won't come on
FAN
TEMP
LAMP
ON
⇒ Problem with internal cooling fan.
(Red lit or flashing)
(Red lit)
• Unplug the power cord, and contact your dealer.
❈ The
Or
icon will appear before the power goes out.
(Orange lit or flashing)
❈ After displaying the abnormal state for about 2 minutes, returns
to standby.
Power went out during use, or power won't come on
FAN
TEMP
LAMP
ON
⇒ The lamp cover is not properly attached.
(Orange
(Red lit)
flashing)
• Unplug the power cord, and reattach the lamp cover.
❈ The
icon will appear before the power goes out.
❈ After displaying the abnormal state for about 2 minutes, returns
to standby.
PRECAUTIONS
• Make sure to unplug the power cord if something goes wrong.
• If the power cord is unplugged before cooling is complete, give the lamp time to cool
before plugging it back in. If the lamp overheats it may fail to light. Unplugging the power
cord repeatedly when the temperature is high will shorten the life of the lamp. (Even if
you are not concerned about lamp lifetime, the light may not come on if you do not wait
at least 3 minutes.)
p.56
p.58
64
Before calling service personnel
If you think something is wrong, check the following before contacting customer service.
p.64
Please see "Trouble indications"
as well.
If This Happens
• Is the power cord plugged in? Is it connected to the projector?
No power
• Is the lamp cover loose?
• Is the ambient temperature high?
Power goes out
during use
• Is the air filter clogged?
• Is the air intake or air exhaust blocked?
• Is the projector turned on?
No picture
• Is the mute function on?
• Is the brightness setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
No audio
• Is the projector turned on?
• Is the mute function on?
• Is the volume setting minimized?
• Are the connections set up correctly?
• Are all the connected devices functioning properly?
• Is the input signal supported by the projector?
Picture not
displayed
• Is the correct video mode selected?
• Is the correct signal format selected?
correctly
• Is the selecting of RGB or Y/P
• Is there something generating an abnormal video signal, for
instance the video tape?
• Is the lens dirty?
Picture blurred
Part of picture
• Is the lens focus adjusted optimally?
• Is the projection distance within the projector's supported range?
out of focus
p.21
• Is the projector's screen placement angle tilted too far?
• Are the sharpness or sampling phase adjustments off?
• Are the brightness or contrast adjustments off?
Image is dark
• Is the lamp nearing the end of its service life?
Colors too light
• Are the color, tint, R-level, G-level, or B-level adjustments off?
• Is the screen dirty?
Bad shading
• Is the lamp nearing the end of its service life?
• Are the remote control's batteries drained?
Remote control
doesn't work
• Are the batteries inserted into the remote control correctly?
• Is the remote control being used within the effective range?
• Are there any obstructions between the remote control and
projector?
• Is the correct operation mode set?
• Are there any fluorescent or other bright lights shining at the
projector's infrared remote sensor?
Check
p.64
p.64
p.64
p.64
p.27
p.30
p.53
p.22
p.27
p.30
p.28
p.22
p.68
,
p.69
p.29
p.29
p.27
/P
input correct?
B
R
p.57
p.28
p.21
p.53 p.29
p.53
p.32
p.32
p.20
65
p.53
p.19
p.19

Advertisement

loading

  Related Manuals for Toshiba TLP-S200