Download Print this page

Using The Menus; How To Use The Menus; The Image Adjustment Menu; The Default Setting Menu - Toshiba TLP-S200 Owner's Manual

3lcd data projector (xga / svga / high brightness / with pc card slot & document camera)
Hide thumbs

Advertisement

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings,
using the operation buttons
p.16
on the control panel (main unit side) and remote control.

How to use the menus

The menu shown below is only for operation
instructions and might be different from the actual
display.
2. Select a Category
To PC card setting menu
p.54
To Image adjustment menu
p.53
To Display setting menu
p.54
To Default setting menu
p.53
3. Adjustments & Settings
Item
Adjustment/Setting Value
These marks signify the
items can be adjusted/set
by using
.
These marks signify an
item can be switched by
using
.
The figure shows a typical example.
As the display may differ depending
on the item, use the following pages
as a reference.
These marks signify the items can be selected from
the list by using
.
After an item selected, apply it by pressing
4. Back
Note
• Menu adjustments and settings (except Lamp power
turned off via the ON/STANDBY button. If the power cord is unplugged before this, or the
power goes out, then the data will not be saved.
1. Start
Display the Setting display menu
Displays the
current adjust-
ment/setting of
each category
5. To Finish
Finish via the Status
display menu.
This mark signfy that
there are options.
Press
to display a
list of options.
To Status display
p.32
.
6. End
The menu disappears
p.53
) are saved when the power is
52

The image adjustment menu

Use this menu to adjust image-related items.
Items Items that can be adjusted are marked with "Yes", and those that cannot are marked
with "No".
Item
Description
Contrast
Lower
Higher
Brightness Darker
Brighter
Color
Lighter
Deeper
Tint
[Note 1]
Reddish
Greenish
Sharpness Softer
Sharper
R-level
Less red
More red
G-level
Less green
More green
B-level
Less blue
More blue
Up/down shift
[Note 2]
Shift down
Shift up
Notes
1: Tint can only be adjusted when Video mode
2: Up/down shift can only be adjusted when Screen size

The default setting menu

This menu shows placement status and other settings.
Item
Projection
Set projection mode in accordance with Placement Style
mode
(Placed
on floor)
No signal
Set the time to wait after signal input stops until turning off the power:
power off
Off (not turned off)
Power on
Set whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual
Lamp power
[Note 1]
Set the lamp power
Standby mode
[Note 2]
Set standby mode according to functions used Standard
Notes
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off. The setting will be back to
"Standard" when the power is turned on next time.
2: The Standby mode function is only available with models equipped with a PC card slot
Notes
• Note that if Power on is set to Auto, then if the power cord is plugged in when power is
restored after a power outage, the projector power will come on.
• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Unplugging the power cord to cut off the power will shorten the life of the lamp.
Video
Computer Y/P
/P
PC Card Camera
B
R
S-video
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
No
No
Yes
No
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
p.29
is NTSC or NTSC4.43.
p.54
is Wide.
Description
p.21
(Hung from
(Back hung
(Rear)
ceiling)
from ceiling)
1 min
2 min
...
60 min
Standard
Low
Economy
p.39
53
Yes
Yes
No
No
Yes
Yes
Yes
Yes
No
Auto
.

Advertisement

loading

  Related Manuals for Toshiba TLP-S200