Toshiba B-EP2DL Owner's Manual page 6

WARNING
This indicates that there is the risk of death or serious injury if the machines are handled
improperly or contrary to this indication.
•
If water or any other liquid enters the machine, turn off the power. Continuous use of the machine under such
conditions may cause fire or electric shock.
•
If the enclosure is damaged when dropped or subject to shock, turn off the power. Continuous use of the
machine under such conditions may cause fire or electric shock.
•
Avoid continuous exposure to direct sunlight or high temperature as this may cause fire.
•
Do not remove covers or modify the machine by yourself. Doing so may cause fire or electric shock.
•
Avoid water, operation with wet hands or cleaning with a moistened cloth. Failure to do this may cause fire or
electric shock.
•
Do not wipe the machine with a cloth moistened with thinner or other volatile solvent as this may cause fire or
electric shock.
•
Use the specified battery only. Failure to do this may cause fire or electric shock.
•
Danger of explosion if the battery is incorrectly replaced. Replace the battery only with TOSHIBA TEC
Corporation, Battery Pack Model B-EP802-BT-QM-R 7.4V 2600mAh Li-ion or B-EP804-BT-QM-R 14.8V
2600mAh Li-ion. Discard used batteries according to the manufacturer's instruction.
•
Do not disassemble and modify the battery because it has a protection unit in it. Doing so may break the
protection unit, causing the battery to heat up, burst or burn.
•
If the battery gets wet, dry it completely. Using a wet battery may cause fire or electric shock.
•
Be aware of the following precautions when using batteries. Otherwise they could heat up, burst or burn.
Do not throw the battery into fire or heat it with a microwave or oven, etc.
Do not load the battery with the electrodes reversed.
Do not connect the electrodes with metal objects like wire. Do not carry or store the battery along with
metal objects such as necklaces, hairpins, etc.
Do not stick a needle into, hammer, step on, or drop the battery.
Do not solder the battery.
Do not leave the battery where the temperature is more than 60°centigrade, such as inside a car or in
direct sunlight.
CAUTION
This indicates that there is the risk of personal injury or damage to objects if the machines are
improperly handled contrary to this indication.
•
Keep away from flame or other sources of heat. Failure to do this may cause fire or machine failure.
•
Do not drop or shock the machine as this may cause machine failure.
•
During lightning, turn off and keep away from the machine because of danger of electric shock and machine
failure.
•
Avoid locations subject to rapid change in temperature as this causes condensation, causing electric shock
or machine failure.
•
Do not damage the print head, platen or strip roller with a sharp object. Doing so may cause machine failure.
•
Do not touch or contact the print head element with a metal object. Doing so may cause machine failure.
•
Use the specified media only. Failure to do this may cause machine failure.
•
Be sure to turn off the machine before replacing the battery, or machine failure may occur.
•
Do not charge the battery near flame or under direct sunlight. High temperature may activate or damage the
protection unit of the battery, disabling the electric charge or causing it to overheat, burst, or burn.
•
Unload the battery when the machine will not be used for a longtime. Failure to do this may cause machine
failure.
•
Keep the battery away from flame, a heat source or other locations subject to high temperature.
Failure to do this may cause it to over heat or burn.
•
Use the specified battery charger only. Failure to do this may cause the battery to overheat, burst or burn.
•
Do not force the battery into the machine or battery charger. Doing so may cause the battery to overheat,
burst or burn. Check for the correct electrode.
•
Do not connect the battery to a power outlet or a car cigarette lighter jack as this may cause the battery to
overheat, burst or burn.
•
Because the B-EP802-BT-QM-R and the B-EP804-BT-QM-R Series battery is exclusively for the B-EP2DL
and the B-EP4DL Series printer, respectively, do not use the battery in other machines. Doing so may
damage the battery or affect the performance and life of the battery.