Maintenance Counter Printing - Toshiba B-570 Maintenance Manual

6. DIAG. TEST OPERATION
Sample Print
[Print Condition]
Preset count
Print speed
Sensor
Printing method : Thermal transfer
Supply length
Issuing mode
1) Maintenance Counter
# Item
Total media distance
(1)
covered
Media distance
(2)
Print distance
(3)
Cut count
(4)
Head up and down
count
(5)
Ribbon motor driving
time
(6)
Solenoid driving time
(7)
RS-232C hardware
(8)
error count
System error count
(9)
Momentary power
(10)
failure count
NOTES: 1. Item from (2) through (10) are initialized to "0" after RAM clear.
2. If the distance is 5.5 m or less, it is rounded down and no data is added to the memory at power
off.
3. If the count is 31 counts or less, it is rounded down and no data is added to the memory at
power off.
4. If the driving time is 27 sec. or less, it is rounded down and no data is added to the memory
at power off.
5. When a sent command results in an error, the same number as the data capacity of the
command is counted by byte.
: 1
: 127 mm/sec.
: No sensor
: 50 mm
: Batch printing
(without rewinder)
Counted when the feed motor drives to feed, print and
issue the media. (Counted also during ribbon save
operation and back feed.) [See NOTE 2].
Counted while printing. (Feeding and issuing media,
and ribbon saving operation are not counted.)
[See NOTE 2.]
Counts every cut. [See NOTE 3.]
Counts every up and down of the print head using the
solenoid for ribbon save operation.
(Up + Down = 1 count) [See NOTE 3.]
Counts when the ribbon motor drives to feed, print
and issue the media. (The driving time is not counted
during ribbon saving operation, but is during back
feed.) [See NOTE 4.]
Counted during ribbon saving operation.
[See NOTE 4.]
Counted when a parity, overrun or framing error
occurs. [See NOTE 5.]
Counted when a zero-dividing error occurs or
undefined command is retrieved.
Counted when a momentary power failure occurs.
TL FEED 1882.3km
(1)
FEED 20.5km
(2)
PRINT 15.0km
(3)
CUT 148150
(4)
HEAD U/D 170
(5)
RIBBON 32h
(6)
SOLENOID 0h
(7)
232C ERR 1
(8)
SYSERR 0
(9)
PW FAIL 0
(10)
FONT [PC-850] [0]
(11)
CODE [ESC LF NUL]
(12)
RIBN [TRANS.]
(13)
RIBN ADJ. [PC] + 0 +0 [KEY] + 0 +0
(25)
STATUS [OFF]
(26)
THRESHOLD R 1.0V
(27)
THRESHOLD T 1.4V
(28)
KANJI [TYPE1]
(29)
EURO CODE B0H
(30)
STACKER [OFF]
(31)
DTR/RTS [DTR]
(32)
INPUT PRIME [ON]
(33)
Count Condition
6-4
EM18-33010A
(Revision Date: Dec. 10 '99)
6.2 SELF TEST MODE
[PC]
FEED -10.0mm
CUT -5.0mm
BACK +3.0mm
TONE(T) +3step
TONE(D) +5step
[KEY]
FEED +5.0mm
CUT -1.5mm
BACK +0.5mm
TONE(T) +0step
TONE(D) +1step
X ADJ. +35.0mm
Range
0.0 ~ 3200.0 km
0.0 ~ 200.0 km
0.0 ~ 200.0 km
0 ~ 1000000 times
0 ~ 2000000 times
0 ~ 2000 hours
0 ~ 1000 hours
0 ~ 255 times
0 ~ 15 times
0 ~ 15 times
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
Fig. 6-1