Toshiba Satellite 2450 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Satellite 2450
  6. User manual
Toshiba Satellite 2450 User Manual

Toshiba Satellite 2450 User Manual

Toshiba personal computer user's manual satellite 2450
Hide thumbs Also See for Satellite 2450:
Table of Contents

Advertisement

Quick Links

See also: User Manual
TOSHIBA
Satellite 2450 Series
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Satellite 2450

Summary of Contents for Toshiba Satellite 2450

  • Page 1 TOSHIBA Satellite 2450 Series Portable Personal Computer User’s Manual...
  • Page 2 © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
  • Page 3 WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher- als or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port,...

  • Page 4: Fcc Conditions

    Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity information TOSHIBA declares, that the product: PS245 conforms to the following Standards: Supplementary Information: This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
  • Page 5 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
  • Page 6 Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made.
  • Page 7 FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
  • Page 8 Instructions for IC CS-03 certified equipment The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
  • Page 9 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit.

  • Page 10: Specifications

    Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
  • Page 11 ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) ❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers.

  • Page 12: General Conditions

    General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
  • Page 13 In other countries, the drive is certified to comply with the requirement pursuant to IEC 825 and EN60825 on class 1 laser product. This computer is equipped with the optical drive in the following list according to the model. Manufacturer TOSHIBA HITACHI HITACHI TEAC Panasonic Communications...

  • Page 15: Table Of Contents

    Table of Contents Preface Manual contents ... xxiii Conventions ... xxiv Abbreviations ... xxiv Icons ... xxiv Keys ... xxiv Key operation ... xxv Display ... xxv Messages ... xxv General Precautions Stress injury ... xxvii Heat injury ... xxvii Pressure or impact damage ...
  • Page 16 DVD-R/-RW drive ... 2-14 DVD Multi drive ... 2-15 Slim Select Bay HDD adaptor (Black) ... 2-16 TOSHIBA Style Bay Bridge media adaptor ... 2-16 Universal AC adaptor ... 2-17 Chapter 3 Getting Started Setting up your work space ... 3-1 General conditions ...
  • Page 17 Changing Lifestyle Bay modules ... 4-3 Removing a module ... 4-3 Installing a module ... 4-4 Using optical media drives ... 4-5 Loading disks ... 4-5 Removing disks ... 4-8 Writing CDs on CD-RW/DVD-ROM drive ... 4-9 Before writing or rewriting ... 4-9 When writing or rewriting ...
  • Page 18 Chapter 5 The Keyboard Typewriter keys ... 5-1 F1 … F12 function keys ... 5-2 Soft keys: Fn key combinations ... 5-2 Emulating keys on enhanced keyboard ... 5-2 Hot keys ... 5-4 Fn Sticky key ... 5-7 Windows special keys ... 5-7 Keypad overlay ...
  • Page 19 SD card care ... 8-5 Memory expansion ... 8-6 Installing memory module ... 8-6 Removing memory module ... 8-11 TOSHIBA Style Bay Bridge media adaptor ... 8-12 Before installing ... 8-13 SmartMedia ... 8-15 Memory Stick ... 8-17 Compact Flash ... 8-18 Bridge media care ...
  • Page 20 Sound system ... 9-20 Monitor ... 9-20 i.LINK (IEEE1394) ... 9-21 Modem ... 9-21 LAN ... 9-23 Wireless LAN ... 9-23 Bluetooth ... 9-24 Real Time Clock ... 9-24 TOSHIBA support ... 9-25 Before you call ... 9-25 Where to write ... 9-25...
  • Page 21 Appendixes Appendix A Specifications ... A-1 Appendix B Display Controller and Modes ... B-1 Appendix C AT Commands ... C-1 Appendix D S-registers ... D-1 Appendix E V.90 ... E-1 Appendix F Internal Modem Guide ... F-1 Appendix G Wireless LAN ... G-1 Appendix H AC Power Cord and Connectors ...
  • Page 22 xxii...

  • Page 23: Preface

    This manual tells how to set up and begin using your Satellite 2450 series computer. It also provides detailed information on configuring your computer, basic opera- tions and care, using optional devices and troubleshooting.

  • Page 24: Conventions

    User's Manual Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, Slim Select Bay modules, USB diskette drive, optical media drives, audio/video controls, microphone, modem, wireless communication features, LAN. It also provides tips on care of the computer, diskettes and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.

  • Page 25: Key Operation

    Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
  • Page 26 User's Manual xxvi...

  • Page 27: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 28: Cpu Performance Disclaimer

    For optimum performance, use your computer product only under recommended conditions Read additional restrictions under “Environmental Requirements” defined in the Appendix A. Contact TOSHIBA Service and Support for more information. PC card overheating Some PC cards can become hot with prolonged use.

  • Page 29: Chapter 1 Introduction

    Carefully unpack your computer. Save the box and packing materials for future use. Hardware Check to make sure you have all the following items: ❑ Satellite 2450 Series Portable Personal Computer ❑ Universal AC adaptor and power cord ❑ USB diskette drive (Provided with some models) ❑...

  • Page 30: Documentation

    • Instruction Manual for Safety & Comfort • End User License Agreement Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complemen- tary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorpo-...
  • Page 31 RTC battery The computer has an internal battery to back up the internal Real Time Clock (RTC) and calendar. Universal AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord.
  • Page 32 User's Manual CD-RW/DVD-ROM Some models are equipped with a full-size, CD-RW/DVD- drive ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 10 speed.
  • Page 33 Display The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 15.0" TFT screen, 16 M colors, with one of the following resolutions: • XGA, 1024 horizontal x 768 vertical pixels •...
  • Page 34 CD player. You can also use the buttons to control the computer’s DVD video player and TOSHIBA Media player when the system is on. Headphone jack This jack outputs analog audio signals.

  • Page 35: Slim Select Bay

    Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets.

  • Page 36: Special Features

    Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Internet button Press this button to launch an Internet browser. See...
  • Page 37 AC adaptor. You can monitor remaining battery capacity. Use the Battery remaining item of the Power Save Modes window in TOSHIBA Power Saver. Battery save mode This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver.

  • Page 38: Utilities

    This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or read.me files. TOSHIBA Power Saver To access this power savings management program, open the Control Panel and select the TOSHIBA Power Saver icon.

  • Page 39: Options

    You can boot ConfigFree from the menu bar as follows. [Start] - [All Programs] - [TOSHIBA ConfigFree] - [ConfigFree] Bluetooth TOSHIBA This software enables communication between remote Stack Bluetooth devices.
  • Page 40 DVD-ROM drive, a CD-RW/DVD-ROM drive, a DVD-R/-RW drive, a DVD Multi drive, a Slim Select Bay HDD adaptor or a TOSHIBA Style Bay Bridge media adaptor, to be preinstalled as a standard device. All other modules are options.

  • Page 41: Chapter 2 The Grand Tour

    Play/pause button: Halts play. Next track/chapter/data. Refer to Chapter 4, NOTE: If Random is selected in TOSHIBA Media Player, selecting Next or Previous advances to a random selection. Mode Control Press this button to switch the mode between CD/DVD button and Digital Audio.

  • Page 42: Left Side

    User's Manual Display latch This latch secures the LCD panel in its closed position. Slide the latch to open the display. Volume control Use this dial to adjust the volume of the stereo speakers and subwoofer or the stereo headphones. System LEDs let you monitor the status of various computer indicators...
  • Page 43 Cooling vents These vents provide an outlet for air pulled through the computer by the fan. CAUTION: Be careful not to block the cooling vents. Also be careful to keep foreign objects out of them. A pin or similar object can damage the computer’s circuitry.

  • Page 44: Right Side

    User's Manual Right side Figure 2-3 shows the computer’s right side. CARD SLOT CARD INDICATOR EADPHONE JACK ICROPHONE JACK Figure 2-3 The right side of the computer SD card slot SD cards are used in a wide variety of external devices. This slot lets you transfer data from the device to your computer.

  • Page 45: Back Side

    Headphone jack This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automatically disabled. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input.
  • Page 46 User's Manual Parallel port This Centronics-compatible, 25-pin parallel port is used to connect a parallel printer or other parallel device. This port supports Extended Capabilities Port (ECP) standard. DC IN 15V The universal AC adaptor connects to this socket. Use only the model of universal AC adaptor that comes with DC IN 15V the computer.

  • Page 47: Underside

    Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. ELECT AY LATCH Figure 2-5 The underside of the computer Slim Select Bay Slide this latch to free the Slim Select Bay for removal. latch CPU cooling fan This cooling fan intakes air to cool cpu and air filter...

  • Page 48: Front With The Display Open

    LEFT OWER BUTTON OUCH Figure 2-6 The front with the display open Display hinge The display hinge holds the display screen at easy-to- view angles. ISPLAY SCREEN TEREO SPEAKER RIGHT BUTTON TOSHIBA ONSOLE BUTTON NTERNET BUTTON OUCH AD CONTROL BUTTONS...
  • Page 49 TOSHIBA Console Press this button to launch an application automatically. button The default is TOSHIBA Console. TV button Press this button to set your display device to TV (Video- out). Press it again to return to LCD.

  • Page 50: System Indicators

    User's Manual System indicators CD/DVD DC IN 15V IGITAL UDIO Figure 2-7 System indicators CD/DVD The CD/DVD indicator glows in green when reproducing CD/DVD. This LED does not light usually and is locked not to light. Press the Mode control button for four seconds to unlock.

  • Page 51: Keyboard Indicators

    Disk The Disk indicator glows green when the computer is accessing the built-in hard disk or fixed optical media drive. Slim Select Bay The Slim Select Bay indicator glows green when the computer is accessing a DVD-ROM drive, CD-RW/DVD- ROM drive, DVD-R/-RW drive, DVD Multi drive or Slim Select Bay HDD adaptor in the Slim Select Bay.

  • Page 52: Usb Diskette Drive

    User's Manual When the CapsLock indicator glows the keyboard is in all-caps mode. Figure 2-9 CapsLock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase. Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys.

  • Page 53: Slim Select Bay Modules

    The Slim Select Bay can accommodate the following modules: DVD-ROM drive, CD- RW/DVD-ROM drive, DVD-R/-RW drive, DVD Multi drive, optional Slim Select Bay HDD adaptor or TOSHIBA Style Bay Bridge media adaptor. DVD-ROM drive Refer to the DVD-ROM drive item in the Fixed optical media drive section for details.

  • Page 54: Cd-Rw/Dvd-Rom Drive

    User's Manual CD-RW/DVD-ROM drive Refer to the CD-RW/DVD-ROM drive item in the Fixed optical media drive section for details. NOTE: The physical features of this drive are similar to those of the DVD-ROM drive. Refer to the illustration in the DVD-ROM drive section. CAUTION: Check the Slim Select Bay indicator when you use the DVD-ROM drive or CD-RW/DVD-ROM drive in the Slim Select Bay.

  • Page 55: Dvd Multi Drive

    DVD Multi drive The full-size DVD Multi drive module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD-RW at up to 8 speed, DVD-R and DVD-RW at single speed, and DVD-RAM at 2 speed.

  • Page 56: Slim Select Bay Hdd Adaptor (Black)

    TOSHIBA Style Bay Bridge Media Adaptor Three types of memory, a Smart Media, a Memory Stick and a Compact Flash memory can be installed and used in the Bridge media adaptor. Figure 2-13 TOSHIBA Style Bay Bridge media adaptor 2-16 ELEASE LATCH...

  • Page 57: Universal Ac Adaptor

    Figure 2-14 The universal AC adaptor CAUTION: Use only the universal AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. Universal AC adaptor Power and Power-Up Modes for details.
  • Page 58 User's Manual 2-18...

  • Page 59: Chapter 3 Getting Started

    Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 60: General Conditions

    User's Manual General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑...

  • Page 61: Seating And Posture

    Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. ELOW EYE LEVEL OOT REST Figure 3-1 Posture and positioning of the computer...

  • Page 62: Lighting

    User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.

  • Page 63: Connecting The Universal Ac Adaptor

    Chapter 6, CAUTION: Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. The current rating for the computer is 6.0 amperes. 1. Connect the power cord to the universal AC adaptor.

  • Page 64: Opening The Display

    User's Manual Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2. Lift the panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display panel.

  • Page 65: Starting Up For The First Time

    2. Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.

  • Page 66: Hibernation Mode

    NOTE: For the computer to shut down in hibernation mode, the hiberna- tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 67: Starting Hibernation

    1. Open the Control Panel. 2. In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. 3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button. 4. Select the Power Save Modes window.

  • Page 68: Standby Mode

    User's Manual CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software.

  • Page 69: Restarting The Computer

    2. Close the display panel. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility discribed in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility discribed in the Control Panel.

  • Page 70: Restoring The Preinstalled Software From The Product Recovery Cd-Rom

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.

  • Page 71: Chapter 4 Operating Basics

    This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, Sub LCD, audio/video controls, the microphone, the internal modem, wireless communication, LAN, TOSHIBA Remote Control and changing Slim Select Bay modules. It also provides tips on caring for your computer, diskettes and CD/DVDs.

  • Page 72: Using The Usb Diskette Drive

    User's Manual Click: Tap the Touch Pad once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB diskette drive A 3 1/2"...

  • Page 73: Disconnecting 3 1/2" Diskette Drive

    2. Before removing or installing a second battery pack, turn off the computer’s power. NOTE: The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction, and to the utility’s online help files for information on using this utility to change modules while the computer’s power is on.

  • Page 74: Installing A Module

    User's Manual CAUTION: Wait for all disk indicators to go out before you turn over the computer and be careful to lay the computer down gently. Shock can damage the HDD or other components. 3. Slide the Slim Select Bay latch to the unlock position. 4.

  • Page 75: Using Optical Media Drives

    Using optical media drives Using optical media drives The text and illustrations in this section refer primarily to the DVD-ROM drive in the Slim Select Bay. However, operation is the same for the CD-RW/DVD-ROM drive and the DVD Multi drive in Slim Select Bay. The full-size drive provides high- performance execution of CD/DVD-ROM-based programs.
  • Page 76 User's Manual b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
  • Page 77 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-8 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray.

  • Page 78: Removing Discs

    User's Manual Figure 4-9 Closing the DVD-ROM drawer Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-10. CAUTION: Do not press the eject button while the computer is accessing the Fixed DVD-ROM drive. Wait for the Disk indicator to go out before you open the drawer.

  • Page 79: Writing Cds On Cd-Rw/Dvd-Rom Drive

    Figure 4-10 Removing a CD/DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. Writing CDs on CD-RW/DVD-ROM drive Depending on the type of drive installed, you may be able to write CDs. The CD- RW/DVD-ROM drive lets you write as well as read CD-ROMs.

  • Page 80: When Writing Or Rewriting

    User's Manual CD-RW: MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ❑ CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.

  • Page 81: Writing Cds On Dvd-R/-Rw Drive

    RW drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: ❑ Damage to any CD-R/-RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product.

  • Page 82: Writing Cds On Dvd Multi Drive

    DVD Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: ❑ Damage to any CD-R/-RW or DVD-R/-RW/-RAM disc that may be caused by writing or rewriting with this product.

  • Page 83: Read/Write Function Chart

    Read/write function chart Disc type CD-R Read Write Drag’n Drop CD*1 DVDfunSTUDIO*1 DVD-MovieAlbum*1 DVD-Video*2 DVD VR*2 (DVD VideoRecoding) *1 Software supplied with the product can be used for writing to a disc. *2 Video format can be written. Writing CD/DVDs on DVD Multi drive CD-RW DVD-R DVD-RW...
  • Page 84 Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/-RW and DVD-R/-RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.

  • Page 85: Before Writing Or Rewriting

    ❑ Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. ❑ Data deleted (erase) from a CD-RW and DVD-RW/-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.

  • Page 86: When Writing Or Rewriting

    User's Manual ❑ Writing with software other than Drag'n Drop CD, DVDfunSTUDIO and DVDMovieAlbum is not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/-RW or DVD-R/-RW/-RAM disc. ❑ Do not perform any of the following actions when writing or rewriting: •...

  • Page 87: Data Verification

    ❑ Do not use the DISC Backup function of Drag'n Drop CD to copy DVD-Video and DVD-ROM with copyright protection, because the copy will not play correctly. ❑ DVD-RAM disc cannot be backed up with the DISC Backup function of Drag'n Drop CD.
  • Page 88 User's Manual ❑ When Drag'n Drop or similar software is resident in the computer's memory, the DVD Multi drive locks. In this situation, other software cannot be used to write data to the disc. ❑ While you are editing DVD-R/-RW/-RAM, you can display previews. However, if an application other than WinDVD is running, the preview might not display properly.

  • Page 89: Media Care

    Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean.

  • Page 90: Modem

    To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 91: Properties Menu

    Figure 4-11 The Region Selection icon 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.

  • Page 92: Connecting

    User's Manual Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region.

  • Page 93: Disconnecting

    Figure 4-13 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1.

  • Page 94: Security

    TOSHIBA strongly recomend the customer to enable the WEP function. 2. TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof.

  • Page 95: Wireless Communication Switch

    If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN. Open or click the following: start, Control Panel, System, Hardware Device Manager, Network adapters, TOSHIBA Wireless LAN Mini PCI Card and enable. Wireless communications 4-25...

  • Page 96: Lan

    User's Manual The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled.

  • Page 97: Disconnecting Lan Cable

    3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. NOTE: When the computer is exchanging data with the LAN, the LAN Active indicator glows yellow. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green.

  • Page 98: Moving The Computer

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver. Maximum...

  • Page 99: Chapter 5 The Keyboard

    The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s key- board layout your computer is configured with.

  • Page 100: F1 ... F12 Function Keys

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
  • Page 101 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard.

  • Page 102: Hot Keys

    User's Manual Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon.
  • Page 103 Soft keys: Fn key combinations Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4, the computer enters Hibernation.
  • Page 104 User's Manual LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver.

  • Page 105: Fn Sticky Key

    Windows special keys Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA Utilities and click Accessibility.

  • Page 106: Temporarily Using Normal Keyboard (Overlay On)

    User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay While using the overlay, you can temporarily access the normal keyboard without...

  • Page 107: Temporarily Using Overlay (Overlay Off)

    Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay.
  • Page 108 User's Manual 5-10...

  • Page 109: Chapter 6 Power And Power-Up Modes

    Power and Power-Up Modes The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether a universal AC adaptor is connected, whether a battery...

  • Page 110: Power Indicators

    User's Manual Table 6-1 Power conditions continued Battery • Operates adaptor charge is • LED: Battery off above low connected battery trigger point Battery • Operates charge is • LED: Battery below low battery trigger point Battery Computer goes charge is into resume mode exhausted shuts down...

  • Page 111: Dc In Indicator

    NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off. DC IN indicator Check the DC IN indicator to determine the power status with the universal AC adaptor connected:...

  • Page 112: Real Time Clock Battery

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recom- mended by TOSHIBA as replacements. 2. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.

  • Page 113: Care And Use Of The Battery Pack

    CAUTION: The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
  • Page 114 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture.
  • Page 115 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.

  • Page 116: Charging The Batteries

    Hibernation mode (so you don’t lose data) and automatically turns off. NOTE: The computer enters Hibernate mode only if Hibernation is enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 117: Monitoring Battery Capacity

    Battery charging notice The battery may not charge right away under the following conditions: ❑ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10°...

  • Page 118: Maximizing Battery Operating Time

    How you configure the computer (for example, whether you enable battery- power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: • Processor speed •...

  • Page 119: Retaining Data With Power Off

    Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack RTC battery Extending battery life To maximize the life of your battery pack: ❑...

  • Page 120: Replacing The Battery Pack

    User's Manual Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.

  • Page 121: Installing The Battery Pack

    RELEASE LATCH Figure 6-1 Releasing the battery cover CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below.

  • Page 122: Starting The Computer By Password

    User's Manual ATTERY RELEASE LATCH Figure 6-2 Securing the battery cover Starting the computer by password To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, message appears: Password = NOTE: At this point, the hot keys Fn + F1 to F5 do not work.

  • Page 123: Power-Up Modes

    Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation. See Chapter 5,...
  • Page 124 User's Manual 6-16...

  • Page 125: Chapter 7 Hw Setup And Passwords

    HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.

  • Page 126: Boot Priority

    User's Manual Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you set the display to be used when the computer is booted. Selects an external monitor if one is connected. Other- Auto-Selected wise, it selects the internal LCD.
  • Page 127 HW Setup. 4. Support of PCA (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. 5. A PCA (ATA) card takes the position of HDD in the Boot Priority Options list.
  • Page 128 User's Manual Built-in HDD PC Card HDDs are searched for a boot command in the following order: the built-in HDD, the PC card and the HDD installed in the Slim Select Bay. 2nd HDD PC Card HDDs are searched for a boot command in the following order: the HDD installed in the Slim Select Bay, the PC card and the built-in HDD.
  • Page 129 USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.
  • Page 130 User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Setup This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings. About Click About to display the HW Setup version. Password User Password This option allows you to set or reset the user password for power on.
  • Page 131 4. If character strings match, the password is registered and the display changes The password was registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2.

  • Page 132: Device Config

    8. Remove the diskette and press any key.Supervisor password Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file.

  • Page 133: Supervisor Password

    Bi-directional Supervisor password Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file. Supervisor password...
  • Page 134 User's Manual 7-10...

  • Page 135: Chapter 8 Optional Devices

    TOSHIBA dealer: Cards/memory ❑ PC cards ❑ SD cards ❑ Memory expansion ❑ TOSHIBA Style Bay Bridge media adaptor (Memory Stick/Smart Media/ Compact Flash memory) Power devices ❑ Battery pack ❑ Universal AC adaptor Peripheral devices ❑...

  • Page 136: Pc Cards

    The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 137: Removing A Pc Card

    Removing a PC card To remove the PC card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5.

  • Page 138: Sd Cards

    User's Manual SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory.

  • Page 139: Removing An Sd Card

    Removing an SD card To remove an SD card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the card and release it to pop the card out slightly. 4.

  • Page 140: Memory Expansion

    Avoid the mat that generates static electricity. CAUTION: Use only memory modules approved by TOSHIBA. CAUTION: Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module.
  • Page 141 4. Turn the computer to the normal position and open the display panel. Tilt the display panel slightly beyond the upright position before removing the keyboard display. 5. Put your fingers on the both ends of the keyboard brace and remove it carefully to the direction indicated with arrows.
  • Page 142 User's Manual 7. Press the keyboard to the other side. Turn the keyboard upside down when a flat cable appears. Figure 8-7 Removing the keyboard (2) Figure 8-8 Removing the keyboard (3)
  • Page 143 Memory expansion 8. Raise the insulation sheet covering the memory module to appear the module. NSULATION SHEET Figure 8-9 Raising the insulation sheet CAUTION: Do not touch VGA chip, or you will get burnt. 9. Keep the insulation sheet raised using adhesive tape. Figure 8-10 Raising the insulation sheet...
  • Page 144 User's Manual 10. Insert a new module to the socket and push it downward to lie flat. Latches on either side will click into place to secure the module. Figure 8-11 Installing a memory module Figure 8-12 Installing two memory modules 11.

  • Page 145: Removing Memory Module

    12. Insert the tabs of the keyboard into the slits of the computer case and seat the keyboard at the original position. Fix it with three screws removed in 6. CAUTIONS: 1. Be sure to use all screws that were removed in 6 and do not leave foreign matters such as adhesive tape used in 9 or screws removed and dropped in the computer.

  • Page 146: Toshiba Style Bay Bridge Media Adaptor

    You can insert three types of flash memory cards — CompactFlash, Memory Stick and SmartMedia — in the computer’s TOSHIBA Style Bay Bridge media adaptor. For details on using the adaptor, follow the steps below. For details on inserting...

  • Page 147: Before Installing

    Bridge media adaptor: one marked A and one marked B. The case for the Satellite Pro M10 is marked with a B. NOTE: Case B is also used with the Satellite 2450 computer. Case A is used with the Satellite 5200 series.
  • Page 148 User's Manual 3. Turn the Bridge media adaptor with case upside down and secure the case to the adaptor with one screw. Figure 8-16 Secureing a screw Removing To remove the Bridge media adaptor from the case, follow the steps below. 1.

  • Page 149: Smartmedia

    TOSHIBA Style Bay Bridge media adaptor SmartMedia This slot accommodates 3.3 V SmartMedia (RAM) from 2 MB to 128 MB. ❑ You cannot use SmartMedia that does not conform to SSFDC specifications. ❑ Operation of SmartMedia developed after the computer was manufactured is not guaranteed.
  • Page 150 User's Manual Figure 8-18 Inserting a SmartMedia Removing CAUTION: Do not remove a SmartMedia card while data is being written or read. Data could be destroyed. Wait for SmartMedia indicator on the left side of the SmartMedia slot to go out. 1.

  • Page 151: Memory Stick

    TOSHIBA Style Bay Bridge media adaptor Memory Stick This slot accommodates Memory Stick from 16MB to 128MB. NOTE: The slot does not support Magic Gate functions. Write protection Memory Stick can be write protected to safeguard your data. To write-protect a Memory Stick, slide the lock on the back of the Memory Stick to the lock position.

  • Page 152: Compact Flash

    User's Manual CAUTION: Make sure the Memory Stick indicator is out before you remove the Memory Stick or turn off the computer’s power. If you remove the Memory Stick or turn off the power while the computer is accessing the Memory Stick, you may lose data or damage the Memory Stick. Compact Flash This slot accommodates Compact Flash from 16MB to 512MB.

  • Page 153: Bridge Media Care

    CAUTION: Make sure the Compact Flash indicator is out before you remove the Compact Flash or turn off the computer’s power. If you remove the Compact Flash or turn off the power while the computer is accessing the Compact Flash you may lose data or damage the Compact Flash.

  • Page 154: Slim Select Bay Hdd Adaptor (Black)

    User's Manual Slim Select Bay HDD adaptor (Black) A integrated 2 1/2" HDD is available for installation in the Slim Select Bay. To install an HDD in the Slim Select Bay HDD adaptor follow the steps below. 1. Slide the lock to the unlock position and open the lid. Figure 8-22 Opening the lid 2.

  • Page 155: External Monitor

    3. Close the lid and slide the lock to the lock position. Figure 8-24 Closing the lid For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating External monitor An external analog monitor can be connected to the external monitor port on the computer.

  • Page 156: Using The Tv Button

    User's Manual You can connect a television set to the TV out jack on the computer. Follow the steps below. Using the TV button 1. Connect the TV adaptor cable’s S-Video plug to the TV out jack on the computer. 2.
  • Page 157 i.LINK (IEEE1394) Figure 8-25 Display properties Select the Adapter tab, then select List all modes. Figure 8-26 The Adapter window (4) Select a resolution from the menu. 8-23...

  • Page 158: I.link (Ieee1394)

    Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data.

  • Page 159: Connecting

    ❑ If you are transferring data through an IEEE1394 hub, do not connect or disconnect other devices from the hub during data transfer. There is a likeli- hood that data will be damaged. Connect all devices to the hub before you turn on the computer’s power.

  • Page 160: Security Lock

    User's Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.

  • Page 161: Chapter 9 Troubleshooting

    Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 162: Analyzing The Problem

    User's Manual ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.

  • Page 163: Hardware And System Checklist

    Hardware If you cannot find a software problem, check your hard- ware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.

  • Page 164: Self Test

    If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ❑...

  • Page 165: Overheating Power Down

    Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally shut down. Problem Procedure Computer shuts down Leave the computer off until the computer and DC IN indicator reaches room temperature, then turn it back on. blinks orange If the computer is still too warm, the DC IN indicator will continue blinking when you turn on...
  • Page 166 If you do not think the battery is at the end of its operating life, see your dealer. Battery doesn’t Check the power consumption settings in power the computer TOSHIBA Power Saver Utility. Consider using a as long as expected power saving mode. Power and Power-Up Modes.

  • Page 167: Password

    Password Problem Procedure Cannot enter Contact your dealer. or forgot password NOTE: For information on setting a password, refer to Chapter 7, Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, Keyboard.

  • Page 168: Hard Disk Drive

    User's Manual Markings appear on They might have come from contact with the the LCD. keyboard, Touch Pad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner. Be sure to let the LCD dry before closing it.

  • Page 169: Dvd-Rom Drive

    DVD-ROM drive For more information, refer to Chapter 4, Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.

  • Page 170: Cd-Rw/Dvd-Rom Drive

    User's Manual Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the The Grand Tour. If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Problem Procedure You cannot access...
  • Page 171 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...

  • Page 172: Dvd-R/-Rw Drive

    User's Manual DVD-R/-RW drive For more information, refer to Chapter 4, Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.

  • Page 173: Dvd Multi Drive

    Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...
  • Page 174 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the...

  • Page 175: Diskette Drive

    • Do not run or start other software during • Do not jar the computer during writing. • Do not connect/ disconnect external devices or If problems persist, contact your dealer. Diskette drive For more information, refer to Chapter 4, Problem Procedure Drive does not...

  • Page 176: Pc Card

    User's Manual You cannot write Make sure the card is not write protected. to an SD card You cannot read Make sure the target file is on the SD a file Card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional...

  • Page 177: Pointing Device

    Pointing device If you are using a USB mouse, also refer to the your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume Pad operation its normal shape and try again to move it.

  • Page 178: Usb Mouse

    User's Manual USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume mouse operation its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.

  • Page 179: Usb

    Refer also to your USB device’s documentation. Problem Procedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documenta- tion for information on checking the drivers.

  • Page 180: Sound System

    User's Manual Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Annoying sound You may be experiencing feedback.

  • Page 181: I.link (Ieee1394)

    Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. i.LINK (IEEE1394) Problem Procedure i.LINK device does Make sure the cable is securely connected to not function the computer and to the device.
  • Page 182 User's Manual You can also use the ATX command. Refer to the online help files for Appendix C, You place a call, Make sure the settings are correct in your but a connection communications application. can’t be made After making a call Make sure the tone or pulse selection in your you can’t hear a ring communications application is set correctly.

  • Page 183: Lan

    You can also use the ATS0 command. Refer to the online help files for Appendix D, S-registers. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN Make sure the universal AC adaptor is con- nected.

  • Page 184: Bluetooth

    User's Manual Bluetooth For more information on wireless communication, refer to Chapter 4, Basics. Problem Procedure Cannot access Make sure the computer’s wireless communica- Bluetooth device tion switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on.

  • Page 185: Toshiba Support

    TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
  • Page 186 User's Manual United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 In Europe Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany France TOSHIBA Systèms France S.A. 7, Rue Ampère B.P. 131,...

  • Page 187: Specifications

    Specifications This appendix summarizes the computer’s technical specifications. Environmental Requirements Ambient Conditions temperature Operating 5°C (41°F) to 35°C (95°F) Non-operating -20°C (-4°F) to 65°C (149°F) Thermal Gradient 20°C per hour maximum Wet-bulb temperature 26°C maximum Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating...
  • Page 188 User's Manual Communication specifications Communication Data: system Fax: Communication Data protocol ITU-T-Rec (Former CCITT) Bell ITU-T-Rec (Former CCITT) Communication Data transmission and reception speed 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/37333/ 38666/40000/41333/42666/44000/45333/46666/48000/ 49333/50666/52000/53333/54666/56000 bps 2400/4800/7200/9600/12000/14400 bps Transmitting level -10 dBm Receiving level -10 to -40 dBm...

  • Page 189: Appendix B Display Controller And Modes

    Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the internal LCD and external monitors.

  • Page 190: Video Modes

    User's Manual Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
  • Page 191 Table1 Video modes (VGA) continued Video Type Resolution mode 320 x 200 Grph Pels 640 x 200 Grph Pels 640 x 350 Grph Pels 640 x 350 Grph Pels 640 x 480 Grph Pels 640 x 480 Grph Pels 320 x 200 Grph Pels Character LCD...
  • Page 192 User's Manual Resolution colors 640 x 480 256/256K 800 x 600 256/256K 1024 x 768 256/256K 1280 x 1024 256/256K (Virtual) 1600 x 1200 256/256K (Virtual) 1920 x 1440 256/256K (Virtual) 2048 x 1536 256/256K (Virtual) Table 2 Video modes (XGA) colors 256/256K 256/256K...
  • Page 193 Table 2 Video modes (XGA) continued Resolution colors 640 x 480 64K/64K 800 x 600 64K/64K 1024 x 768 64K/64K 1280 x 1024 64K/64K (Virtual) 1600 x 1200 64K/64K (Virtual) 1920 x 1440 64K/64K (Virtual) 2048 x 1536 64K/64K (Virtual) Appendix B Vertical colors...
  • Page 194 User's Manual Table 2 Video modes (XGA) continued Resolution colors 640 x 480 16M/16M 800 x 600 16M/16M 1024 x 768 16M/16M 1280 x 1024 16M/16M (Virtual) 1600 x 1200 16M/16M (Virtual) 1920 x 1440 16M/16M (Virtual) 2048 x 1536 16M/16M (Virtual) Vertical...
  • Page 195 Table 3 Video modes (Super XGA+) Resolution colors 640 x 480 256/256K 800 x 600 256/256K 1024 x 768 256/256K 1280 x 1024 256/256K 1400 x 1050 256/256K 1600 x 1200 256/256K (Virtual) 1920 x 1440 256/256K (Virtual) 2048 x 1536 256/256K (Virtual) Appendix B...
  • Page 196 User's Manual Table 3 Video modes (Super XGA+) continued Resolution colors 640 x 480 64K/64K 800 x 600 64K/64K 1024 x 768 64K/64K 1280 x 1024 64K/64K 1400 x 1050 64K/64K 1600 x 1200 64K/64K (Virtual) 1920 x 1440 64K/64K (Virtual) 2048 x 1536 64K/64K...
  • Page 197 Table 3 Video modes (Super XGA+) continued Resolution colors 640 x 480 16M/16M 800 x 600 16M/16M 1024 x 768 16M/16M 1280 x 1024 16M/16M 1400 x 1050 16M/16M 1600 x 1200 16M/16M (Virtual) 1920 x 1440 16M/16M (Virtual) 2048 x 1536 16M/16M (Virtual) Appendix B...
  • Page 198 User's Manual B-10...

  • Page 199: At Commands

    AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value for that command.
  • Page 200 User's Manual Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
  • Page 201 Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while...
  • Page 202 User's Manual Monitor speaker volume This command sets speaker volume to low, medium, or high. Low volume. Low volume. (Same as L0) Medium volume (default). High volume. Result Codes: n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode This command turns the speaker on or off. The speaker is off.
  • Page 203 Result Codes: n=0,1 ERROR Otherwise On Return on-line to data mode Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). This command issues a retrain before returning to on-line data mode. This command issues a rate renegotiation before returning to on-line data mode.
  • Page 204 User's Manual Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
  • Page 205 Enable Enable Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
  • Page 206 User's Manual &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: n=0,1 ERROR Otherwise &Dn DTR control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal.
  • Page 207 &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
  • Page 208 User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
  • Page 209 \Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Direct mode. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects.
  • Page 210 User's Manual \Vn Protocol result code Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise % B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed.
  • Page 211 S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
  • Page 212 User's Manual Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
  • Page 213 Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII Command line editing character (user defined)
  • Page 214 User's Manual Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction.
  • Page 215 S37 Dial line rate S37 = 0 (default) S37 = 1 S37 = 2 S37 = 3 S37 = 4 S37 = 5 S37 = 6 S37 = 7 S37 = 8 S37 = 9 S37 = 10 S37 = 11 S37 = 12 S37 = 13 S37 = 14...
  • Page 216 User's Manual AT command set result codes The following table shows the result codes. The result code summary Result Code CONNECT RING NO CARRIER ERROR CONNECT 1200 EC* NO DIAL TONE BUSY NO ANSWER CONNECT 2400 EC* CONNECT 4800 EC* CONNECT 9600 EC* CONNECT 14400 EC* CONNECT 19200 EC*...
  • Page 217 Result Code DELAYED* BLACKLISTED* BLACKLIST FULL* *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
  • Page 218 User's Manual...
  • Page 219 V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 220 User's Manual Table E-1 Result codes for a V.90 connection Result code CONNECT 32000 EC* CONNECT 36000 EC* CONNECT 40000 EC* CONNECT 44000 EC* CONNECT 48000 EC* CONNECT 52000 EC* CONNECT 56000 EC* CONNECT 28000 EC* CONNECT 29333 EC* CONNECT 30666 EC* CONNECT 33333 EC* CONNECT 34666 EC* CONNECT 37333 EC*...
  • Page 221 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 222 User's Manual...

  • Page 223: Appendix F

    Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled. The following is for informa- tion only.
  • Page 224 User's Manual 5. Pull the guide (plastic tab) toward the direction shown by arrow, then lift the HDD. Be careful not to damage the connector. UIDE PLASTIC TAB 6. Remove two screws, which you use later to secure the modem board. 7.

  • Page 225: Card Specifications

    Wireless LAN Card Specifications Form Factor - Mini PCI TypeIII Capability - EEE 802.11 Standard for Wireless LANS (DSSS) Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) Network Operating - Microsoft Windows® Networking System Media Access - CSMA/CA (Collision Avoidance) with Acknowledgment Protocol (ACK) Data Rate...
  • Page 226 Subject to the radio regulations that apply in your country, your Wireless LAN Card may support a different set of 5GHz / 2.4GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region.
  • Page 227 When installing Wireless LAN Cards, the channel configuration is managed as follows: ❑ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required.
  • Page 228 User's Manual Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850 MHz Channel ID 5210 5250 5290 5760 5800 *1: Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition; A Wireless LAN card receive a "US country code" beacon of the standard IEEE802.11 (Revision D) from the near Wireless LAN Access Point.

  • Page 229: Ac Power Cord And Connectors

    AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size: Current rating:...

  • Page 230: Usa And Canada

    User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada UL approved CSA approved Australia AS approved United Kingdom BS approved Europe Approved by the appropriate agency...

  • Page 231: Parts Numbers

    Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules and communication devices.
  • Page 232 User's Manual Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice.
  • Page 233 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only...
  • Page 234 Adaptor (Abbreviations continued) TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus UXGA: ultra extended graphics array VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology XGA: extended graphics array adaptor: A device that provides an interface between two dissimilar electronic devices.

  • Page 235: Cache Memory

    backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system com- mands or executable files. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers.
  • Page 236 capacity capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB.
  • Page 237 components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instruc- tions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.
  • Page 238 device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 239 (FDD): An electro- mechanical device that reads and writes to floppy disks. See also diskette. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. hard disk drive (HDD) folder: An icon in Windows used to store documents or other folders.
  • Page 240 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 241 jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connect- ing two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equiva- lent to 1024, or 2 raised to the 10th power.
  • Page 242 microprocessor microprocessor: A hardware compo- nent contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode.
  • Page 243 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A...
  • Page 244 A Class A device is sufficient for office use. Class B provides a more stringent classifica- tion for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
  • Page 245 TouchPad: A pointing device inte- grated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switch- ing transistors for gates and storage.
  • Page 246 Glossary Glossary-14...
  • Page 247 1-9 types 6-3 Battery charger 1-11 Battery pack 1-2, 2-7 additional 1-11, 8-19 replacing 6-12 Bluetooth 1-7 problems 9-24 TOSHIBA Stack, utility 1-11 using 4-24 Boot mode 3-7 Boot priority 7-2 Bridge media adaptor 1-12 view 2-16 care 8-19...
  • Page 248 User's manual Environment 3-1 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory Fn + Ctrl (enhanced keyboard simula- tion) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4...
  • Page 249 Key FD 7-8 Keyboard 1-5, 5-1 emulating enhanced keyboard 5-2 F1 … F12 function keys 5-2 Fn Sticky key 5-7 hot keys 5-4 problems 9-7 typewriter keys 5-1 Windows special keys 5-7 Keypad overlay 1-9, 5-7 arrow mode 5-7 numeric mode 5-8 temporarily using normal keyboard (overlay on) 5-8 temporarily using overlay (overlay...
  • Page 250 Index-4 password 9-7 PC card 9-16 power 9-4 SD card 9-15 self test 9-4 sound system 9-20 support from TOSHIBA 9-25 system start-up 9-3 Touch Pad 9-17 USB 9-19 Wireless LAN 9-23 Processor 1-2 Real time clock battery, See battery...
  • Page 251 2-9 volume control 2-2 Standby 1-10 automatic 1-8 setting 3-10 System indicators, See indicators TOSHIBA Console 1-10 TOSHIBA Console button 1-8, 2-9 TOSHIBA Controls 1-10 TOSHIBA Power Saver 1-10 Touch Pad 1-5 buttons 2-9 location 2-8 problems 9-17 using 4-1...
  • Page 252 User's manual Index-6...

This manual is also suitable for:

Satellite 2450 series

Table of Contents