Toshiba Satellite A10 Series User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Satellite A10 Series
  6. User manual
Toshiba Satellite A10 Series User Manual

Toshiba Satellite A10 Series User Manual

Toshiba satellite a10 series portable personal computer user's manual
Hide thumbs Also See for Satellite A10 Series:
Table of Contents

Advertisement

Quick Links

See also: Maintenance Manual
TOSHIBA
Satellite A10 Series
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Satellite A10 Series

Summary of Contents for Toshiba Satellite A10 Series

  • Page 1 TOSHIBA Satellite A10 Series Portable Personal Computer User’s Manual...
  • Page 2 © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
  • Page 3 WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripher- als or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port,...

  • Page 4: Fcc Conditions

    Telephone: (949) 583-3000 EU Declaration of Conformity information TOSHIBA declares, that the product: PSA10 conforms to the following Standards: Supplementary Information: This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
  • Page 5 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
  • Page 6 FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.

  • Page 7: Region Selection

    Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made.
  • Page 8 Instructions for IC CS-03 certified equipment The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, opera- tional and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
  • Page 9 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit.
  • Page 10 Notes for use of this device in New Zealand The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
  • Page 11 ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers.

  • Page 12: General Conditions

    General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
  • Page 13 TEAC CD-ROM drive CD-224E, CD- RW/DVD-ROM drive DW-224E safety instruction CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 14 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PROD- UCT.”...
  • Page 15 Toshiba DVD-ROM drive SD-C2612, CD-RW/DVD-ROM drive SD-R2412, DVD-R/-RW drive SD-R6012 safety instruction CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 16 MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED: TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME MINATO-KU, TOKYO 105-8001, JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
  • Page 17 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING vermeiden darf das Gerät nicht geöffnet werden. ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på...
  • Page 18 HITACHI DVD-ROM drive GDR-8082 safety instruction CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
  • Page 19 CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
  • Page 20 Panasonic CD-RW /DVD-ROM drive UJDA-740/750 safety instruction CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 21 Location of the required label CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Panasonic Communications Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.”...
  • Page 22 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på...

  • Page 23: Table Of Contents

    Table of Contents Preface Manual contents ... xxxi Conventions ... xxxii Abbreviations ... xxxii Icons ... xxxii Keys ... xxxiii Key operation ... xxxiii Display ... xxxiii Messages ... xxxiii General Precautions Stress injury ... xxxv Heat injury ... xxxv Pressure or impact damage ...
  • Page 24 Communications ... 1-7 Security ... 1-7 Software ... 1-7 Special features ... 1-7 Utilities ... 1-9 Options ... 1-11 Chapter 2 The Grand Tour Front with the display closed ... 2-1 Left side ... 2-2 Right side ... 2-3 Back side ... 2-4 Underside ...
  • Page 25 Restoring the preinstalled software from the Product Recovery CD-ROM ... 3-12 Chapter 4 Operating Basics Pointing devices ... 4-1 Using the Touch Pad ... 4-1 Using the USB diskette drive ... 4-2 Connecting 3 1/2" diskette drive ... 4-2 Disconnecting 3 1/2" diskette drive ... 4-3 Using optical media drives ...
  • Page 26 Chapter 5 The Keyboard Typewriter keys ... 5-1 F1 … F12 function keys ... 5-2 Soft keys: Fn key combinations ... 5-2 Emulating keys on enhanced keyboard ... 5-2 Hot keys ... 5-4 Fn Sticky key ... 5-7 Windows special keys ... 5-7 Keypad overlay ...
  • Page 27 Chapter 7 HW Setup and Passwords HW Setup ... 7-1 Accessing HW Setup ... 7-1 HW Setup window ... 7-1 Supervisor password ... 7-10 Chapter 8 Optional Devices PC cards ... 8-2 Inserting a PC card ... 8-2 Removing a PC card ... 8-3 Memory expansion ...
  • Page 28 Sound system ... 9-22 Monitor ... 9-22 Modem ... 9-23 LAN ... 9-24 Wireless LAN ... 9-25 Real Time Clock ... 9-25 TOSHIBA support ... 9-26 Before you call ... 9-26 Where to write ... 9-26 Appendixes Appendix A Specifications ... A-1 Appendix B Display Controller and Modes ...
  • Page 29 Appendix I Parts Numbers ... I-1 Glossary Index xxix...

  • Page 31: Preface

    This manual tells how to set up and begin using your Satellite A10 series computer. It also provides detailed information on configuring your computer, basic opera- tions and care, using optional devices and troubleshooting.

  • Page 32: Conventions

    Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB diskette drive, optical media drives, modem, wireless communica- tion features, LAN. It also provides tips on care of the computer, diskettes and CD/ DVDs. Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hot keys.

  • Page 33: Keys

    Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+).
  • Page 34 xxxiv...

  • Page 35: General Precautions

    General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 36: Cpu Performance Disclaimer

    For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under "Environmental Requirements" defined in the Appendix A. Contact TOSHIBA Technical Service and Support for more information. PC Card overheating Some PC cards can become hot with prolonged use.
  • Page 37 Chapter 1 Introduction Equipment checklist ... 1-1 Hardware ... 1-1 Software ... 1-1 Documentation ... 1-2 Features ... 1-2 Processor ... 1-2 Memory ... 1-3 Power ... 1-3 Disks ... 1-3 Display ... 1-5 Keyboard ... 1-5 Pointing device ... 1-6 Ports ...

  • Page 39: Chapter 1 Introduction

    Carefully unpack your computer. Save the box and packing materials for future use. Hardware Check to make sure you have all the following items: Satellite A10 Series Portable Personal Computer Universal AC adaptor and power cord USB diskette drive (Provided with some models)

  • Page 40: Documentation

    User's Manual • Online manual Product Recovery CD-ROM Documentation • Satellite A10 Series Portable Personal Computer User's Manual • Microsoft Windows XP manual package • Instruction Manual for Safety & Comfort • End User License Agreement Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple- mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability.

  • Page 41: Memory

    Memory Slots 128, 256 or 512 MB memory modules can be installed in the two memory slots for a maximum of 1 GB system memory. Video RAM Allocated a part of System Memory dynamically. (Limit of graphics memory is 32MB at 128MB of System Memory, Limit of Graphics memory is 64MB at more than 256MB of System Memory) Power...
  • Page 42 User's Manual • • • • CD-G (Audio CD only) • Addressing Method 2 DVD-ROM drive Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12cm(4.72") DVDs without using an adaptor.

  • Page 43: Display

    DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.

  • Page 44: Pointing Device

    User's Manual Pointing device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer. Ports Parallel Some models are equipped with a parallel port for parallel printer or other parallel device (ECP compatible).Note that some models are not equipped with this port.

  • Page 45: Communications

    Plug and Play capability enables the system to recognize the connection and make the necessary configurations automatically. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Special features...
  • Page 46 Power is restored when any key is pressed or when there is input from a pointing device. You can specify the time in the Turn off monitor item of the Power Save Mode window in TOSHIBA Power Saver. HDD automatic...

  • Page 47: Utilities

    This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Power Saver To access this power savings management program, open the Control Panel and select the TOSHIBA Power Saver icon.
  • Page 48 This Windows program lets you define your own “short- cut” keys to quickly launch applications and speed your work in Windows. To start the utility, click the Windows Start button, point to All Programs, point to TOSHIBA Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD-Video.

  • Page 49: Options

    Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. Universal AC adaptor If you use your computer at more than one site frequently,...
  • Page 50 User's Manual 1-12...
  • Page 51 Chapter 2 The Grand Tour Front with the display closed ... 2-1 Left side ... 2-2 Right side ... 2-3 Back side ... 2-4 Underside ... 2-6 Front with the display open ... 2-7 System indicators ... 2-8 Keyboard indicators ... 2-9 USB diskette drive ...

  • Page 53: Chapter 2 The Grand Tour

    The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. OLUME CONTROL IRELESS COMMUNICATION INDICATOR...

  • Page 54: Left Side

    User's Manual Wireless Slide this switch toward the left of the computer to turn communication off Wireless LAN function. Slide it toward the right of switch the computer to turn on the functions (Wireless LAN model or Wireless LAN ready model only). CAUTION: Set the switch to off in airplanes and hospitals.

  • Page 55: Right Side

    Headphone jack This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automati- cally disabled. PC card slot A PC card slot can accommodate one 5 mm Type II card. You can install any industry standard PC card such as a SCSI adaptor, Ethernet adaptor or flash memory card.

  • Page 56: Back Side

    User's Manual DVD-R/-RW drive Some models are equipped with a full-size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run CD/DVDs without using an adaptor.You can also write CD/DVDs. Modem jack In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a tele- phone line.
  • Page 57 Link indicator This indicator glows green when the computer is connect- (green) ed to a LAN and the LAN is functioning properly. Parallel port Some models are equipped with a Centronics-compatible, 25-pin parallel port that is used to connect a parallel printer or other parallel device.This port supports Extended Capabilities Port (ECP) standard.

  • Page 58: Underside

    User's Manual Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. ATTERY RELEASE LATCH Figure 2-5 The underside of the computer Battery release Slide this latch to release the battery pack for removal. latch For detailed information on removing the battery packs,refer to Chapter 6,...

  • Page 59: Front With The Display Open

    Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle. ISPLAY HINGE TEREO SPEAKER LEFT...

  • Page 60: System Indicators

    User's Manual Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Power button Press the power button to turn the computer’s power on and off. Touch Pad A Touch Pad located slightly in the left from the center of the palm rest is used to control the on-screen pointer.

  • Page 61: Keyboard Indicators

    CD-ROM This indicator glows green when the computer is drive accessing a diskette in the diskette drive or a disk in the CD-ROM,DVD-ROM, DVD-R/-RW or CD-RW/DVD-ROM drive. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator.

  • Page 62: Usb Diskette Drive

    User's Manual Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keyboard. Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights green.

  • Page 63: Fixed Optical Media Drive

    NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 2. Do not set anything on top of the diskette drive. Fixed optical media drive CD-ROM drive Some models are equipped with a full-size,CD-ROM drive.

  • Page 64: Cd-Rw/Dvd-Rom Drive

    User's Manual DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly. Code Region 1. Canada, United States 2. Japan, Europe, South Africa, Middle East Southeast Asia, East Asia 4.

  • Page 65: Dvd-R/-Rw Drive

    Code Region 1. Canada, United States 2. Japan, Europe, South Africa, Middle East Southeast Asia, East Asia 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6. China DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor.

  • Page 66: Universal Ac Adaptor

    Figure 2-11 The universal AC adaptor CAUTION: Use only the universal AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. 2-14 Power and Power-Up Modes for details.
  • Page 67 Chapter 3 Getting Started Setting up your work space ... 3-1 General conditions ... 3-2 Placement of the computer ... 3-2 Seating and posture ... 3-3 Lighting ... 3-4 Work habits ... 3-4 Connecting the universal AC adaptor ... 3-5 Opening the display ...

  • Page 69: Chapter 3 Getting Started

    Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 70: General Conditions

    User's Manual General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.

  • Page 71: Seating And Posture

    Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. ELOW EYE LEVEL OOT REST Figure 3-1 Posture and positioning of the computer...

  • Page 72: Lighting

    User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.

  • Page 73: Connecting The Universal Ac Adaptor

    CAUTION: Use only the AC adaptor that came with the computer or an equivalent optional adaptor.Use of the wrong adaptor could damage your computer.TOSHIBA assumes no liability for any damage in such case. 1. Connect the power cord to the universal AC adaptor.

  • Page 74: Opening The Display

    User's Manual Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2. Lift the panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display panel.

  • Page 75: Starting Up For The First Time

    2. Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.

  • Page 76: Hibernation Mode

    NOTE: For the computer to shut down in hibernation mode, the hiberna- tion feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 77: Starting Hibernation

    1. Open the Control Panel. 2. In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. 3. Select the Hibernate window, select the Enable Hibernate support check box and click the Apply button. 4. Select the Power Save Modes window.

  • Page 78: Standby Mode

    NOTE: When the AC adaptor is used, the computer goes into Standby mode depending on the setting of the TOSHIBA Power Saver feature. • To restore operation, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW setup.
  • Page 79 2. Close the display panel. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button. This feature must be enabled. Refer to the Power Mode item in Power Saver Utility described in the Control Panel.

  • Page 80: Restarting The Computer

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
  • Page 81 Chapter 4 Operating Basics Pointing devices ... 4-1 Using the Touch Pad ... 4-1 Using the USB diskette drive ... 4-2 Connecting 3 1/2" diskette drive ... 4-2 Disconnecting 3 1/2" diskette drive ... 4-3 Using optical media drives ... 4-3 Loading discs ...
  • Page 82 Moving the computer ... 4-23 Heat dispersal ... 4-24...

  • Page 83: Chapter 4 Operating Basics

    Operating Basics This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication, and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Pointing devices The computer is equipped with a Touch Pad as a pointing device.

  • Page 84: Using The Usb Diskette Drive

    User's Manual Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44- megabyte or 720-kilobyte diskettes.

  • Page 85: Disconnecting 3 1/2" Diskette Drive

    Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.

  • Page 86: Loading Discs

    User's Manual Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. Figure 4-3 Pressing the DVD-ROM eject button b.
  • Page 87 2. Pinch the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.

  • Page 88: Removing Discs

    User's Manual CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Be careful to keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4.

  • Page 89: Writing Cds On Cd-Rw/Dvd-Rom Drive

    CAUTIONS: 1. When the drawer pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the drawer fully open. 2. Turn off the power before you use the eject hole. If the CD/DVD is spinning when you open the drawer, the CD/DVD could fly off the spindle and cause injury.

  • Page 90: Before Writing Or Rewriting

    CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufac- turers above. Operation of other media cannot be guaranteed. CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.

  • Page 91: Writing Cd/Dvds On Dvd-R/-Rw Drive

    RW drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product.
  • Page 92 User's Manual Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.

  • Page 93: Read/Write Function Chart

    Read/write function chart Disc type CD-R Read Write Drag’n Drop CD*1 *1 Software supplied with the product can be used for writing to a disc. Writing CD/DVDs on DVD-R/-RW drive CD-RW DVD-R DVD-RW DVD-RAM DVD+R DVD+RW 4-11...
  • Page 94 Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-RW disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.

  • Page 95: Before Writing Or Rewriting

    Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data. Before writing or rewriting Please observe the following points when you write or rewrite data.

  • Page 96: Drag'n Drop Cd+Dvd

    User's Manual Make sure writing or rewriting is completed before going into standby/ hibernation. Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand. Keep mobile phones and other wireless communication devices away from the computer.

  • Page 97: Media Care

    Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean.

  • Page 98: Modem

    To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. NOTE: Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 99: Properties Menu

    3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.

  • Page 100: Connecting

    User's Manual Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region.

  • Page 101: Disconnecting

    Figure 4-11 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1.

  • Page 102: Security

    TOSHIBA strongly recommend the customer to enable the WEP function. 2. TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof.

  • Page 103: Wireless Communication Indicator

    W-LAN. Open or click the following: start, Control Panel, System, Hardware Device Manager, Network adapters, TOSHIBA Wireless LAN Mini PCI Card and enable. The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx).

  • Page 104: Connecting Lan Cable

    User's Manual Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a CAT5 cable.

  • Page 105: Cleaning The Computer

    CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.

  • Page 106: Heat Dispersal

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Power Save Mode window in TOSHIBA Power Saver. Maximum...
  • Page 107 Chapter 5 The Keyboard Typewriter keys ... 5-1 F1 … F12 function keys ... 5-2 Soft keys: Fn key combinations ... 5-2 Emulating keys on enhanced keyboard ... 5-2 Hot keys ... 5-4 Fn Sticky key ... 5-7 Windows special keys ... 5-7 Keypad overlay ...

  • Page 109: Chapter 5 The Keyboard

    The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s key- board layout your computer is configured with.

  • Page 110: F1 ... F12 Function Keys

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
  • Page 111 Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard.

  • Page 112: Hot Keys

    User's Manual Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon.
  • Page 113 Soft keys: Fn key combinations Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4, the computer enters Hibernation.
  • Page 114 User's Manual LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver.

  • Page 115: Fn Sticky Key

    Windows special keys Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA Utilities and click Accessibility.

  • Page 116: Temporarily Using Normal Keyboard (Overlay On)

    User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay Temporarily using normal keyboard (overlay While using the overlay, you can temporarily access the normal keyboard without...

  • Page 117: Temporarily Using Overlay (Overlay Off)

    Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay.
  • Page 118 User's Manual 5-10...
  • Page 119 Chapter 6 Power and Power-Up Modes Power conditions ... 6-1 Power indicators ... 6-2 Battery indicators ... 6-2 DC IN indicator ... 6-3 Power indicator ... 6-3 Battery types ... 6-3 Battery pack ... 6-4 Real Time Clock battery ... 6-4 Care and use of the battery pack ...

  • Page 121: Chapter 6 Power And Power-Up Modes

    Power and Power-Up Modes The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether a universal AC adaptor is connected, whether a battery...

  • Page 122: Power Indicators

    User's Manual Table 6-1 Power conditions continued Battery • Operates adaptor charge is • LED: Battery off above low connected battery trigger point Battery • Operates charge is • LED: Battery below low battery trigger point Battery Computer goes charge is into resume mode exhausted shuts down...

  • Page 123: Dc In Indicator

    No light Under any other conditions, the indicator does not light. NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume. This occurs whether the computer’s power is on or off.

  • Page 124: Battery Pack

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recom- mended by TOSHIBA as replacements. 2. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.

  • Page 125: Care And Use Of The Battery Pack

    Press [F1] key to set Date/Time. CAUTION: The computer’s RTC battery is a nickel metal hydride battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
  • Page 126 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might...
  • Page 127 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.

  • Page 128: Charging The Batteries

    Hibernation mode (so you don’t lose data) and automatically turns off. NOTE: The computer enters Hibernate mode only if Hibernation is enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
  • Page 129 Battery type Power on Battery pack 3600mAh 4400mAh RTC battery NOTE: The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer. If you make heavy use of external devices, for example, the battery might scarcely charge at all during operation.

  • Page 130: Monitoring Battery Capacity

    How you configure the computer (for example, whether you enable battery- power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: • Processor speed •...

  • Page 131: Retaining Data With Power Off

    How much charge the battery contained to begin with. How you use optional devices, such as a PC card, to which the battery supplies power. Enabling Standby mode conserves battery power if you are frequently turning the computer off and on. Where you store your programs and data.

  • Page 132: Replacing The Battery Pack

    User's Manual 4. Connect the universal AC adaptor to the computer and the power cord to a power outlet. The DC IN indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged.

  • Page 133: Installing The Battery Pack

    RELEASE LATCH Figure 6-1 Releasing the battery pack CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below.
  • Page 134 Dispose of the battery as required by local ordinances or regulations. Use only batteries recom- mended by TOSHIBA as replacements. 2. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch.

  • Page 135: Starting The Computer By Password

    Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation. See Chapter 5,...

  • Page 136: Panel Power Off

    User's Manual Panel power off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. NOTE: If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed.

  • Page 137: Hw Setup

    Chapter 7 HW Setup and Passwords HW Setup ... 7-1 Accessing HW Setup ... 7-1 HW Setup window ... 7-1 Supervisor password ... 7-10...

  • Page 139: Chapter 7 Hw Setup And Passwords

    HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.
  • Page 140 User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Setup This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings. About Click About to display the HW Setup version. Password User Password This option allows you to set or reset the user password for power on.
  • Page 141 4. If character strings match, the password is registered and the display changes The password was registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2.

  • Page 142: Device Config

    User's Manual Key FD After you set a password, you can create a Key FD (diskette). If you forget the user password, the Key FD lets you bypass the password function. NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost.
  • Page 143 Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. Sets the port type to Extended Capabilities Port (ECP).

  • Page 144: Boot Priority

    User's Manual Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled. When Switchable the computer is in use, CPU operation is automatically switched when necessary. (Default) CPU power consumption and clock speed automatic Always High switching function is disabled.
  • Page 145 HW Setup. 4. Support of PC (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. 5. A PC (ATA) card takes the position of HDD in the Boot Priority Options list.
  • Page 146 User's Manual HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD PC Card (Default) HDDs are searched for a boot command in the following...
  • Page 147 USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.

  • Page 148: Supervisor Password

    User's Manual Supervisor password Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:\Program Files\TOSHIBA\Windows Utilities\SVPWTool. In the SVPWTool directory, open the readme.htm file. 7-10...
  • Page 149 Chapter 8 Optional Devices PC cards ... 8-2 Inserting a PC card ... 8-2 Removing a PC card ... 8-3 Memory expansion ... 8-4 Installing memory module ... 8-4 Removing memory module ... 8-6 Battery pack ... 8-7 Universal AC adaptor ... 8-7 USB FDD kit ...

  • Page 151: Chapter 8 Optional Devices

    Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ❑ PC cards ❑ Memory expansion Power devices ❑ Battery pack ❑...

  • Page 152: Pc Cards

    The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 153: Removing A Pc Card

    Removing a PC card To remove the PC card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5.

  • Page 154: Memory Expansion

    RAM. This section describes how to install and remove a memory module. CAUTION: 1. Use only memory modules approved by TOSHIBA. 2. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module.
  • Page 155 Figure 8-3 Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module’s connectors into the computer’s connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection. CAUTION: Do not touch the connectors on the memory module or on the computer.

  • Page 156: Removing Memory Module

    User's Manual Figure 8-4 Installing the memory module 8. Seat the cover and secure it with a screw. 9. Replace the battery pack as described in Chapter 6, Modes. 10. Turn the power on and make sure the added memory is recognized. Open System Properties in the Control Panel and click the General tab.

  • Page 157: Battery Pack

    Battery pack Figure 8-5 Removing the memory module Seat the cover and secure it with a screw and replace the battery pack. Battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery.

  • Page 158: External Monitor

    User's Manual External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2.

  • Page 159: Changing The Resolution

    e. Select Television icon. f. Select the Video Standard list box and select the format that your TV supports. *Please select one of them, NTSC-M, NTSC-J or PAL-B from the Video Standard list box though there are lots of selections. Changing the resolution to 640x480 for TV If you want to change the resolution into 640x480 because it is difficulty to read character on TV, follow the steps below.
  • Page 160 User's Manual Figure 8-7 The Adapter window (4) Select a resolution from the menu. Figure 8-8 Resolution menu 8-10...

  • Page 161: Security Lock

    Security lock Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the back side of the computer.
  • Page 162 User's Manual 8-12...
  • Page 163 Memory expansion ... 9-21 Sound system ... 9-22 Monitor ... 9-22 Modem ... 9-23 LAN ... 9-24 Wireless LAN ... 9-25 Real Time Clock ... 9-25 TOSHIBA support ... 9-26 Before you call ... 9-26 Where to write ... 9-26...

  • Page 165: Chapter 9 Troubleshooting

    Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 166: Analyzing The Problem

    User's Manual Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.

  • Page 167: Hardware And System Checklist

    Hardware If you cannot find a software problem, check your hard- ware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.

  • Page 168: Self Test

    If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.

  • Page 169: Overheating Power Down

    Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally shut down. Problem Procedure Computer shuts down Leave the computer off until the computer and DC IN indicator reaches room temperature, then turn it back on. flashes orange If the computer is still too warm, the DC IN indicator will continue blinking when you turn on...
  • Page 170 If you do not think the battery is at the end of its operating life, see your dealer. Battery doesn’t Check the power consumption settings in power the computer TOSHIBA Power Saver Utility. Consider using a as long as expected power saving mode.

  • Page 171: Password

    Password Problem Procedure Cannot enter Contact your dealer. or forgot password NOTE: For information on setting a password, refer to Chapter 7, Keyboard Keyboard problems can be caused by your setup configuration. For more informa- tion refer to Chapter 5, Keyboard.
  • Page 172 User's Manual • The way to replace the key-top Press the key-top until you hear a click after removing a metal spring from the key-top, hooking it to projecting parts and aligning the center of the key-top. Enter, Back Space, Shift and Space key RESS FROM THE UPSIDE PRING ROJECTING...
  • Page 173 Hardware and system checklist • Follow the steps below when a plastic spring is out of place together with a key- top. 1. Remove the plastic spring from the key-top. 2. Attach the plastic spring to the key board with its flat face downward after confirming the direction.

  • Page 174: Lcd Panel

    User's Manual 3. Press from the upside until you hear a click after replacing the key-top to the right position. LCD panel Problem Procedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.

  • Page 175: Hard Disk Drive

    Hard disk drive Problem Procedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD-ROM is in the optical media drive. Remove drive any diskette and/or CD-ROM and check Boot priority. Refer to Chapter 7, There may be a problem with your operating system files.
  • Page 176 User's Manual A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner.

  • Page 177: Dvd-Rom Drive

    DVD-ROM drive For more information, refer to Chapter 4, Problem Procedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.

  • Page 178: Cd-Rw/Dvd-Rom Drive

    User's Manual Check the type of CD/DVD you are using. The drive supports: DVD-ROM: CD-ROM: Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the 2, The Grand Tour . If problems persist, contact your dealer.
  • Page 179 Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the for details on cleaning. Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem. Make sure the others do not hardware configuration matches your software’s needs.

  • Page 180: Dvd-R/-Rw Drive

    Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...
  • Page 181 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during • Use only the software supplied with the •...

  • Page 182: Diskette Drive

    User's Manual Diskette drive For more information, refer to Chapter 4, Problem Procedure Drive does not There may be a faulty cable connection. Check operate the connection to the computer and to the drive. You cannot access Try another diskette. If you can access the the external 3 1/2"...

  • Page 183: Pointing Device

    Pointing device If you are using a USB mouse, also refer to the your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume Pad operation its normal shape and try again to move it.

  • Page 184: Usb Mouse

    User's Manual USB mouse Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume mouse operation its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port.

  • Page 185: Usb

    Refer also to your USB device’s documentation. Problem Procedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documenta- tion for information on checking the drivers.

  • Page 186: Sound System

    User's Manual Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional...

  • Page 187: Modem

    Modem Refer to the online help files for Problem Procedure Communication Make sure the computer’s internal modem software can’t settings are correct. Refer to Phone and Modem initialize modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make sure the communication application’s tone dial a call...

  • Page 188: Lan

    User's Manual Character display In data transmission, make sure the parity bit becomes garbled and stop bit settings correspond with those during a of the remote computer. communication Check the flow control and communication protocol. You cannot receive Check the rings before auto answer setting in an incoming call You can also use the ATS0 command.

  • Page 189: Wireless Lan

    Wireless LAN If the following procedures do not restore LAN access, consult your LAN adminis- trator. For more information on wireless communication, refer to Chapter 4, Basics. Problem Procedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on. If problems persist, contact your LAN administra- tor or dealer.

  • Page 190: Toshiba Support

    User's Manual TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for addi- tional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
  • Page 191 United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 In Europe Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany France TOSHIBA Systèms France S.A. 7, Rue Ampère B.P. 131,...
  • Page 192 User's Manual 9-28...

  • Page 193: Appendixes

    Appendixes Appendix A Specifications ... A-1 Appendix B Display Controller and Modes ... B-1 Appendix C AT Commands ... C-1 Appendix D S-registers ... D-1 Appendix E V.90 ... E-1 Appendix F Internal Modem Guide ...F-1 Appendix G Wireless LAN ... G-1 Appendix H AC Power Cord and Connectors ...

  • Page 195: Physical Dimensions

    Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 332 (w) x 293 (d) x 33/40 (h) millimeters (not including parts that extend beyond the main body) Weight 2.9 kilograms, configured with: 15"XGA-TFT, CD-RW/ DVD-ROM drive, Modem, Wireless LAN Weight will vary with other configurations.
  • Page 196 User's Manual Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication Data: system Fax: Communication Data protocol ITU-T-Rec...

  • Page 197: Display Controller And Modes

    Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the internal LCD and external monitors.

  • Page 198: Video Modes

    User's Manual Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
  • Page 199 Table1 Video modes (VGA) continued Video Type Resolution mode 320 x 200 Grph Pels 640 x 200 Grph Pels 640 x 350 Grph Pels 640 x 350 Grph Pels 640 x 480 Grph Pels 640 x 480 Grph Pels 320 x 200 Grph Pels Character LCD...
  • Page 200 User's Manual Resolution colors 640 x 480 256/256K 800 x 600 256/256K 1024 x 768 256/256K 1280 x 1024 256/256K (Virtual) 1400 x 1050 256/256K (Virtual) 1600 x 1200 256/256K (Virtual) 1920 x 1440 256/256K (Virtual) Table 2 Video modes (XGA) colors 256/256K 256/256K...
  • Page 201 Table 2 Video modes (XGA) continued Resolution colors 640 x 480 64K/64K 800 x 600 64K/64K 1024 x 768 64K/64K 1280 x 1024 64K/64K (Virtual) 1400 x 1050 64K/64K (Virtual) 1600 x 1200 64K/64K (Virtual) 1920 x 1440 64K/64K (Virtual) Appendix B Vertical colors...
  • Page 202 User's Manual Table 2 Video modes (XGA) continued Resolution colors 640 x 480 16M/16M 800 x 600 16M/16M 1024 x 768 16M/16M 1280 x 1024 16M/16M (Virtual) 1400 x 1050 16M/16M (Virtual) 1600 x 1200 16M/16M (Virtual) 1920 x 1440 16M/16M (Virtual) Vertical...
  • Page 203 Table 3 Video modes (Super XGA+) Resolution colors 640 x 480 256/256K 800 x 600 256/256K 1024 x 768 256/256K 1280 x 1024 256/256K 1400 x 1050 256/256K 1600 x 1200 256/256K (Virtual) 1920 x 1440 256/256K (Virtual) Appendix B Vertical colors frequency (Hz)
  • Page 204 User's Manual Table 3 Video modes (Super XGA+) continued Resolution colors 640 x 480 64K/64K 800 x 600 64K/64K 1024 x 768 64K/64K 1280 x 1024 64K/64K 1400 x 1050 64K/64K 1600 x 1200 64K/64K (Virtual) 1920 x 1440 64K/64K (Virtual) Vertical colors...
  • Page 205 Table 3 Video modes (Super XGA+) continued Resolution colors 640 x 480 16M/16M 800 x 600 16M/16M 1024 x 768 16M/16M 1280 x 1024 16M/16M 1400 x 1050 16M/16M 1600 x 1200 16M/16M (Virtual) 1920 x 1440 16M/16M (Virtual) Appendix B Vertical colors frequency (Hz)
  • Page 206 User's Manual B-10...

  • Page 207: At Commands

    AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value for that command.
  • Page 208 User's Manual Answer command This command instructs the modem to go off-hook and answer an incoming call. Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default).
  • Page 209 Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while...
  • Page 210 User's Manual Monitor speaker volume This command sets speaker volume to low, medium, or high. Low volume. Low volume. (Same as L0) Medium volume (default). High volume. Result Codes: n=0,1,2,3 ERROR Otherwise Monitor speaker mode This command turns the speaker on or off. The speaker is off.
  • Page 211 Result Codes: n=0,1 ERROR Otherwise Return on-line to data mode Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). This command issues a retrain before returning to on-line data mode. This command issues a rate renegotiation before returning to on-line data mode.
  • Page 212 User's Manual Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
  • Page 213 Enable Enable Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
  • Page 214 User's Manual &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default).
  • Page 215 &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
  • Page 216 User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
  • Page 217 Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. Buffer mode. No error control. Direct mode. MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects.
  • Page 218 User's Manual Protocol result code Disable protocol result code appended to DCE speed. Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 ERROR Otherwise View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed.

  • Page 219: Appendix D S-Registers

    S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
  • Page 220 User's Manual Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
  • Page 221 Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII Command line editing character (user defined)
  • Page 222 User's Manual Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction.
  • Page 223 Dial line rate S37 = 0 (default) S37 = 1 S37 = 2 S37 = 3 S37 = 4 S37 = 5 S37 = 6 S37 = 7 S37 = 8 S37 = 9 S37 = 10 S37 = 11 S37 = 12 S37 = 13 S37 = 14...
  • Page 224 User's Manual AT command set result codes The following table shows the result codes. The result code summary Result Code CONNECT RING NO CARRIER ERROR CONNECT 1200 EC* NO DIAL TONE BUSY NO ANSWER CONNECT 2400 EC* CONNECT 4800 EC* CONNECT 9600 EC* CONNECT 14400 EC* CONNECT 19200 EC*...
  • Page 225 Result Code DELAYED* BLACKLISTED* BLACKLIST FULL* *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
  • Page 226 User's Manual...
  • Page 227 V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 228 User's Manual Table E-1 Result codes for a V.90 connection Result code CONNECT 32000 EC* CONNECT 36000 EC* CONNECT 40000 EC* CONNECT 44000 EC* CONNECT 48000 EC* CONNECT 52000 EC* CONNECT 56000 EC* CONNECT 28000 EC* CONNECT 29333 EC* CONNECT 30666 EC* CONNECT 33333 EC* CONNECT 34666 EC* CONNECT 37333 EC*...
  • Page 229 *EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 230 User's Manual...

  • Page 231: Appendix F Internal Modem Guide

    Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled. The following is for informa- tion only.
  • Page 232 User's Manual 9. Secure the cover with one screw. Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3.

  • Page 233: Appendix G Wireless Lan

    Wireless LAN Card Specifications Form Factor - Mini PCI TypeIII Capability - I EEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance. Network Operating - Microsoft Windows®...
  • Page 234 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN Card may support a different set of 5GHz / 2.4GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 235 When installing Wireless LAN Cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required.
  • Page 236 User's Manual Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850 MHz Channel ID 5210 5250 5290 5760 5800 *1: Available Area: US (USA, CANADA) only Note US only *1 US only *1 US only *1 US only *1 US only *1...

  • Page 237: Ac Power Cord And Connectors

    AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Wire size: Current rating:...

  • Page 238: Usa And Canada

    User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe. USA and Canada UL approved CSA approved Australia AS approved United Kingdom BS approved Europe Approved by the appropriate agency...

  • Page 239: Parts Numbers

    Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, and communication devices.
  • Page 240 Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice.
  • Page 241 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only...
  • Page 242 Adaptor (Abbreviations continued) TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus UXGA: ultra extended graphics array VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology XGA: extended graphics array adaptor: A device that provides an interface between two dissimilar electronic devices.

  • Page 243: Cache Memory

    backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system com- mands or executable files. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers.
  • Page 244 capacity capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB.
  • Page 245 components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instruc- tions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.
  • Page 246 device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 247 (FDD): An electro- mechanical device that reads and writes to floppy disks. See also diskette. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. hard disk drive (HDD) folder: An icon in Windows used to store documents or other folders.
  • Page 248 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 249 characteristics by electrically connect- ing two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equiva- lent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device contain- ing switches that are activated by manually pressing marked keys.
  • Page 250 microprocessor mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/ demodulator, a device that converts (modulates) digital data for transmis- sion over telephone lines and then converts modulated data (demodu- lates) to digital format where received.
  • Page 251 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A...
  • Page 252 A Class A device is sufficient for office use. Class B provides a more stringent classifica- tion for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
  • Page 253 TouchPad: A pointing device inte- grated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switch- ing transistors for gates and storage.
  • Page 254 Glossary Glossary-14...
  • Page 255 Index AC adaptor, See Universal AC adaptor ASCII characters 5-9 Battery automatic hibernation 1-8 charging 6-8 extending life 6-11 indicator 2-8, 6-2 location 2-6 monitoring capacity 6-10 real time clock 1-3, 6-4 safety precautions 6-5 save mode 1-9 types 6-3 Battery charger 1-11 Battery pack 1-3, 2-6 additional 1-11, 8-7...
  • Page 256 User's manual work habits 3-4 Expansion memory, See Memory Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5...
  • Page 257 LAN 1-7 connecting 4-22 disconnecting 4-22 jack 2-5 LAN active indicator 2-4 link indicator 2-5 problems 9-24 LCD, See Display, Video modes and Monitor external Level 2 cache, See Cache memory Lock security, See Security lock Media care CD/DVDs 4-15 diskettes 4-15 Memory 1-3 expansion 1-11, 8-4...
  • Page 258 PC card 9-18 pointing device 9-19 power 9-4 real time clock 9-25 self test 9-4 sound system 9-22 support from TOSHIBA 9-26 system start-up 9-3 Touch Pad 9-19 USB 9-21 Wireless LAN 9-25 Processor 1-2 Real time clock battery, See battery...
  • Page 259 Index Wireless LAN 1-7 problems 9-25 using 4-19 Index-5...

Table of Contents