Bosch AL 1810 CV Original Instructions Manual page 7

ger. Do not charge any non-re-
chargeable batteries. Otherwise
there is a risk of fire and explosion.
Do not expose the charger to rain or wet condi-
tions. Water entering a power tool will increase the risk of
electric shock.
Keep the charger clean. Dirt poses a risk of electric
u
shock.
Always check the charger, cable and plug before use.
u
Stop using the charger if you discover any damage. Do
not open the charger yourself, and have it repaired
only by a qualified specialist using only original re-
placement parts. Damaged chargers, cables and plugs
increase the risk of electric shock.
Do not operate the charger on an easily ignited sur-
u
face (e.g. paper, textiles, etc.) or in a flammable envir-
onment. There is a risk of fire due to the charger heating
up during operation.
Recharge only with the charger specified by the manu-
u
facturer. A charger that is suitable for one type of bat-
tery pack may create a risk of fire when used with another
battery pack.
In case of damage and improper use of the battery, va-
u
pours may also be emitted. Ensure the area is well-vent-
ilated and seek medical attention should you experience
any adverse effects. The vapours may irritate the respirat-
ory system.
Under abusive conditions, liquid may be ejected from
u
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addi-
tionally seek medical help. Liquid ejected from the bat-
tery may cause irritation or burns.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Product Features
The numbering of the components shown refers to the dia-
gram of the charger on the graphics page.
A)
(1) Battery
(2) Charging slot
Bosch Power Tools
(3) Green battery charge indicator
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Charger
Article number
Battery charging voltage
(automatic voltage detec-
tion)
Charge current
Permitted charging temper-
ature range
Charging time at battery ca-
pacity, approx.
– 18 V / 1.5 Ah
– 18 V / 2.0 Ah
– 18 V / 2.5 Ah
– 18 V / 3.0 Ah
– 18 V / 4.0 Ah
– 18 V / 6.0 Ah
Number of battery cells
Weight according to
EPTA-Procedure 01:2014
Protection class
Operation
Start-up
Note the mains voltage! The voltage of the power source
u
must match the voltage specified on the rating plate of
the charger. Chargers marked with 230 V can also be op-
erated with 220 V.
Charging process
The charging process begins as soon as the mains plug for
the charger is inserted into the mains socket and the battery
(1) is inserted into the charging slot (2).
Thanks to the intelligent charging process, the charge condi-
tion of the battery is automatically detected and then
charged up with the optimal charge current depending on
battery temperature and voltage.
In this way, the battery is treated with care and remains per-
manently fully charged when it is stored in the charger.
Note: The charging process is only possible when the tem-
perature of the battery is within the permitted charging tem-
perature range, see section "Technical data".
English | 7
AL 1810 CV
2 607 226 3..
V 14.4/18
mA 1000
°
C 0 - 45
(80%) / 100%
min (72) / 94
min (96) / 124
min (120) / 154
min (144) / 184
min (192) / 244
min (288) / 364
4 - 10
kg 0.17
/ II
1 609 92A 4XZ | (15.04.2019)