Page 1 TECRA A2 TOSHIBA TECRA A2 Portable Personal Computer User’s Manual...
Page 2 This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA A2 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice.
Page 3: Fcc Information
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, IEEE1394...
Page 4 Contact Address: Telephone: (949) 583-3000 TOSHIBA declares, that the product: PTA20* conforms to the following Standards: Supplementary Information: This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Page 5: Region Selection
Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany Greece Portugal Spain Switzerland All other countries/ regions Specific switch settings or software setup are required for each network,...
Page 6: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 7: Fax Branding
Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number of the sending machine or such business, other entity or individual.
Page 8 The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
Page 9 Notes for use of this device in New Zealand The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
Page 10: General Conditions
When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.
Page 11: Optical Disc Drive Safety Instructions
The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100. The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications.
Page 12 User’s Manual DVD Super Multi DV-W24E The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 13 TOSHIBA DVD-ROM SD-C2612 The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 14 User’s Manual DVD-ROM&CD-R/RW SD-R2512 The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 15 User’s Manual DVD-R/-RW SD-R6112, SD-R6332 The DVD-R/-RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 16 HITACHI LG DVD-ROM&CD-R/RW GCC-4241N The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 17 Panasonic DVD-ROM&CD-R/RW UJDA750 The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 18 User’s Manual DVD-R/-RW UJ-811BTJB-A The DVD-R/-RW employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 19 User’s Manual DVD Super Multi UJ-820 The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 20 International precautions CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TOEN60825 ADVERSEL:USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTSLSE FOR STRÅLING CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
Page 21 User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Page 22 User’s Manual xxii User’s Manual...
Page 23: Table Of Contents
TECRA A2 Table of Contents Preface Manual contents ......... xxix Conventions.
Page 24 Keyboard indicators ........2-11 USB floppy disk drive.
Page 25 DLA for TOSHIBA ........
Page 26 The Keyboard Typewriter keys ......... . . 5-1 F1 …...
Page 27 Accessing HW Setup ........7-1 HW Setup window .
Page 28 TOSHIBA support ........
Page 29: Manual Contents
This manual tells how to set up and begin using your TECRA A2 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Page 30: Conventions
Chapter 5, the keypad overlay and hot keys. Chapter 6, Power and Power-Up power resources and battery save modes. Chapter 7, HW Setup and Passwords computer using the HW Setup program. Chapter 8, Optional Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly.
Page 31: Key Operation
Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Page 32 Preface xxxii User’s Manual...
Page 33: General Precautions
TECRA A2 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 34: Pressure Or Impact Damage
For optimum performance, use your computer product only under recommended conditions. Read additional restrictions under “Environmental Conditions” in your product Resource Guide. Contact TOSHIBA Service and Support for more information. xxxiv...
Page 35: Rtc Battery
RTC battery The following message is Displayed on the LCD: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The battery for RTC is wearing. Set the date and time in BIOS setup with the following steps: 1.
Page 36 General Precautions xxxvi User’s Manual...
Page 37: Introduction
Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Page 38: Software
Instruction Manual for Safety & Comfort End User License Agreement Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: User’s Manual...
Page 39 Memory Slots Video RAM Power Battery pack RTC battery AC adaptor User’s Manual The slot accepts a 256, 512 or 1,024 MB memory modules can be installed in the two memory slots for a maximum of 2,048 MB system memory. Maximum 64 MB of RAM is provided for video display.
Page 40 Disks Hard disk drive About 2GB disk space is reserved for recovery partition. When re-setting up your hard disk, do not change, delete or add partitions in a manner other than specified in the manual. Otherwise, space for software may be destroyed. In addition, if you use a third-party partitioning program to reconfigure partitions on your hard disk, it may become impossible to re-setup your computer.
Page 41 DVD-ROM drive DVD-ROM&CD-R/RW drive User’s Manual Some models are equipped with a full-size, DVD- ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CDs or 12cm(4.72") DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
Page 42 DVD-R/-RW drive DVD Super Multi drive Display The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in Graphics controller Some models are equipped with a full- size DVD- R/-RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs...
Page 43: Pointing Device
Keyboard Built-in Pointing Device Built-in Touch Pad Ports Parallel External monitor Universal Serial Bus (USB 2.0) Docking interface Slots PC card Multimedia Sound system Headphone jack Microphone jack User’s Manual 85 keys or 86 keys, compatible with IBM enhanced keyboard, embedded numeric overlay, dedicated cursor control, Refer to Chapter 5, Keyboard, for details.
Page 44 Communications Modem Wireless LAN An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to V.90 section in Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line.
Page 45: Special Features
Security lock slot Software Operating System TOSHIBA Utilities Plug and Play Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. TOSHIBA Console button TOSHIBA Presentation button...
Page 46 Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver. This feature automatically shuts down the system...
Page 47 Use the Fan item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on fan first, then if Performance necessary lowers CPU processing speed.
Page 48: Utilities
TOSHIBA Zooming Utility RecordNow! Basic for TOSHIBA 1-12 TOSHIBA Console is a graphical user interface that provides easy access to help and services. It is the function launched by the TOSHIBA Console button. To access this power savings management program, click the Control Panel and select the TOSHIBA Power Saver icon.
Page 49 DLA for TOSHIBA TOSHIBA PC DiagnosticTool TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy TOSHIBA Touch Pad On/Off Utility User’s Manual DLA (Drive Letter Access) is the packet writing software which provides the function which writes files and/or folders to DVD+RW, DVD-RW or CD- RW disc via a drive letter like a floppy disk or other removable disks.
Page 50: Options
Security lock USB floppy disk Kit Advanced Port Replicator III The TECRA A2 does not support the DVI and i.LINK ports on the Advanced Port Replicator. 1-14 A 256, 512 or 1,024 MB memory module (PC2100 / PC2700 DDR) can easily be installed in the computer.
Page 51: The Grand Tour
TECRA A2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position.
Page 52: Left Side
Left side Figure 2-2 shows the computer’s left side. Cooling vents Security lock External monitor port Cooling vents Do not to block the cooling vents. Also do not to keep foreign objects out of them. A pin or similar object can damage the computer’s circuitry. Wireless communication switch...
Page 53: Right Side
PC card slot Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry. Security lock Right side Figure 2-3 shows the computer’s right side. Headphone jack Volume control Volume control Headphone jack Microphone jack User’s Manual A PC card slot can accommodate a 5 mm Type II...
Page 54: Backside
Fixed Optical media drive Universal Serial Bus (USB 2.0) port DC IN 15V jack DC IN 15V Backside Figure 2-4 shows the computer’s back panel. Parallel port The computer is configured with a full-size optical media drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") disks without using an adaptor.
Page 55 Parallel port Modem jack In case of a lightning storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem. LAN jack Ether Link indicator (green) LAN active indicator (orange)
Page 56: Underside
Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery release latch (1) Memory module cover Battery release latch Battery release latch Battery pack Notches Notches Battery pack Figure 2-5 The underside of the computer Slide this lock to release the battery pack for removal.
Page 57: Front With The Display Open
LCD Sensor switch (Not shown) Stereo speaker (Left) TOSHIBA Console button TOSHIBA Presentation button Figure 2-6 The front of the Touch Pad model with the display open User’s Manual This port enables connection of an optional Advanced Port Replicator III described in...
Page 58 PC changes its display mode to the multi-monitor display on LCD and CRT. You can also return to single display by pressing this button twice. The setting of TOSHIBA Presentation button can be changed through the property of TOSHIBA Console. Display mode is changed to the multi- monitor display by selecting "Different Image"...
Page 59 Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”. Refer to the TOSHIBA Power Saver Utility and Panel Power Off/On items in Chapter 1, Introduction, for details on...
Page 60: System Indicators
System indicators DC IN 15V DC IN 15V Power Battery Built-in HDD 2-10 Power Battery Figure 2-7 System indicators The DC IN 15V indicator glows green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
Page 61: Keyboard Indicators
Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers.
Page 62: Usb Floppy Disk Drive
USB floppy disk drive A 3 1/2" floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks. It connects to the USB port. Disk-In-Use Indicator Disk-In-Use Indicator Floppy disk slot Eject button Check the Disk-In-Use indicator when you use the floppy disk drive. Do not press the eject button or turn off the computer while the light is glowing.
Page 63: Fixed Optical Media Drives
Fixed optical media drives One of the following optical media drives is installed in the computer: CD- ROM, DVD-ROM, DVD-ROM&CD-R/RW, DVD-R/-RW, DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.
Page 64: Dvds
DVDs DVD-R discs can be written only once. The recorded data cannot be erased or changed. DVD-RW discs can be recorded more than once. DVD-RAM discs can be recorded more than once. DVD+R discs can be written only once. The recorded data cannot be erased or changed.
Page 65: Dvd-Rom&Cd-R/Rw Drive
DVD-ROM&CD-R/RW drive The full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
Page 66: Ac Adaptor
Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. Use only the AC Adapter supplied with your computer or an equivalent adapter that is compatible.
Page 67: Getting Started
TECRA A2 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Setting up your work space — for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Page 68: General Conditions
General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. Make sure there is adequate space around the computer for proper ventilation. Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Page 69: Seating And Posture
Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. Below eye level Foot rest...
Page 70: Work Habits
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch.
Page 71: Connecting The Ac Adaptor
4. Secure the battery pack releace latch(1). Check the battery lock was changed to the lock position. (to the direction of the right) Battery release latch(1) Refer to Removing the battery pack Power-Up Modes for removing the battery pack. Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power.
Page 72 Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual.
Page 73: Opening The Display
Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly.
Page 74: Windows Xp Setup
3. Press and hold the computer’s power button for two or three seconds. Windows XP setup When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Professional Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode.
Page 75: Hibernation Mode
For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.
Page 76: Standby Mode
When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.
Page 77 1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
Page 78: Restarting The Computer
Standby limitations Standby will not function under the following conditions: Power is turned back on immediately after shutting down. Memory circuits are exposed to static electricity or electrical noise. Restarting the computer Certain conditions require that you reset the system. For example, if: You change certain computer settings.
Page 79: Restoring The Preinstalled Software From The Recovery Hdd
2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu.
Page 80 Getting Started When you select the 4 option from the menu, the HDD Recovery Area on your HDD will be deleted. Then, in the recovery process, all partitions are put into one partition and the recovery is performed. You cannot any longer execute the recovery action using the steps described in the section "Restoring the preinstalled software from the Recovery HDD."...
Page 81: Operating Basics
TECRA A2 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive, optical media drives, Sound System, modem, the wireless communication and LAN. It also provides tips on caring for your computer and on heat dispersal.
Page 82: Using The Usb Floppy Disk Drive
Click: Tap the Touch Pad once Double-click: Tap the Touch Pad twice Drag and drop: 1. Hold down the left control button and move the cursor to drag the item you want to move. 2. Lift your finger to drop the item where you want it. Scroll: Vertical: Move your finger up or down the right edge of the Touch Pad.
Page 83: Disconnecting 3 1/2" Floppy Disk Drive
Disconnecting 3 1/2" floppy disk drive When you have finished using the floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped. If you disconnect the floppy disk drive or turn off the power while the computer is accessing the drive you may lose data or damage the floppy disk or the drive.
Page 84: Loading Discs
Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. b. Pressing the eject button will not open the drawer when the DVD- ROM drive’s power is off.
Page 85 3. Lay the CD/DVD, label side up, in the drawer. When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-6.
Page 86: Removing Discs
Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-8. Do not press the eject button while the computer is accessing the DVD- ROM drive. Wait for the optical media drive indicator to go out before you open the drawer.
Page 87: Writing Cds On Dvd-Rom&Cd-R/Rw Drive
MITSUBISHI CHEMICAL CORPORATION, RICOH Co., Ltd. Ultra-Speed CD-ROM: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.
Page 88: When Writing Or Rewriting
Write from the computer's HDD to the CD. Do not try to write from shared devices such as a LAN server or any other network device. Writing with software other than Sonic RecordNow! has not been confirmed. Therefore, operation with other software cannot be guaranteed.
Page 89: Important Message (Dvd-R/-Rw Drive)
Disclaimer (DVD-R/-RW drive) TOSHIBA does not bear responsibility for the following: Damage to any CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product.
Page 90: Before Writing Or Rewriting
Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
Page 91: When Writing Or Rewriting
Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW or DVD+R/+RW discs. Data written to a CD-R/DVD-R/DVD+R disc cannot be deleted either in whole or in part. In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc.
Page 92: Recordnow! Basic For Toshiba
Always copy data from the HDD to the DVD-RAM. Do not use cut-and- paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: DVD-Video cannot be created using RecordNow!.
Page 93: Data Verification
3. Mark the Verify data written to the disc after burning check box in the Data Options. 4. Click the OK button. DLA for TOSHIBA Note the following limitations when you use DLA: This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW).
Page 94: When Windvd Creator 2 Platinum Is Used
While you are editing DVD-R/-RW/+R/+RW/-RAM, you can display previews. However, if an application other than WinDVD is running, the preview might not display properly. To ensure proper display of previews, do not start other applications while you are editing DVD-R/- RW/+R/+RW/-RAM disc.
Page 95: Media Care
Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.
Page 96: Volume Control
Volume control The Volume Control utility lets you control the audio volume in Windows for both playback and recording. To launch Volume Control for playback, click Start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control. To launch Recording Control, click Options, point to Properties, choose Recording and click OK.
Page 97: Region Selection
To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA Internal Modem and click Region Select Utility. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Page 98: Modem Selection
Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match.
Page 99: Connecting
Connecting To connect the modem cable, follow the steps below. The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. In case of a lightning storm, unplug the modem cable from the telephone jack.
Page 100: Wireless Lan
TOSHIBA strongly recommend the customer to enable the WEP function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Wireless communication switch You can enable or disable Wireless LAN function, with the on/off switch.
Page 101: Wireless Communication Indicator
Wireless communication indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indicator off Indicator glows If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN. Open or click the following: start, Control Panel, System, Hardware Device Manager, Network adapters, Atheros AR5001X+ Wireless Network Adapter or Intel®...
Page 102: Connecting Lan Cable
Connecting LAN cable To connect the LAN cable, follow the steps below. 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place.
Page 103: Cleaning The Computer
Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.
Page 104: Heat Dispersal
CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Performance...
Page 105: The Keyboard
TECRA A2 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.
Page 106: F1 ... F12 Function Keys
Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 107: Hot Keys
Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay operate these keys.
Page 108 Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the profile item in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification.
Page 109 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. The brightness level is always set at the maximum value for about 18 seconds, when the LCD turns on.
Page 110: Fn Sticky Key
Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.
Page 111: Turning On The Overlays
Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode F10 indicator lights. Now try cursor and page control using the keys shown in figure 5-2. Press Fn + F10 again to turn off the overlay.
Page 112: Temporarily Using Overlay (Overlay Off)
Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry.
Page 113: Power And Power-Up Modes
TECRA A2 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Page 114 Battery charge adaptor is above low battery trigger connected point Battery charge is below low battery trigger point Battery charge is exhausted No battery installed Table 6-1 Power conditions continued Power on • Operates • LED: Battery off DC IN 15V off •...
Page 115: Power Indicators
Power indicators As shown in the above table, the Battery, DC IN 15V and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: Flashing orange Orange...
Page 116: Power Indicator
Power indicator Check the Power indicator to determine the power status: Green Blinking orange No light Battery types The computer has two types of batteries: Battery packs High Capacity battery pack (8800mAh) Battery pack (4400mAh) Real Time Clock (RTC) battery High Capacity battery pack An optional High Capacity battery is installable instead of a main battery.
Page 117: Battery Pack
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode.Data is stored in RAM, so if the computer loses power it will be lost.When the computer is powered off in Standby mode, and the AC...
Page 118: Real Time Clock Battery
Press [F1] key to set Date/Time. The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
Page 119 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. User’s Manual...
Page 120 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.
Page 121: Charging The Batteries
The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.
Page 122: Monitoring Battery Capacity
Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Page 123: Maximizing Battery Operating Time
How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: CPU Precessing speed...
Page 124: Extending Battery Life
Extending battery life To maximize the life of your battery pack: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1.
Page 125: Removing The Battery Pack
(to the direction of the left), then slide out the battery pack. Battery release latch (1) For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. User’s Manual Battery pack Figure 6-3 Releasing the battery pack...
Page 126: Installing The Battery Pack
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch.
Page 127: Starting The Computer By Password
Refer also to the sections in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.
Page 128: System Auto Off
System Auto Off This feature turns the system off automatically if it is not used for a set duration. The system shuts down in Standby mode or Hibernation mode in Windows. 6-16 User’s Manual...
Page 129: Hw Setup And Passwords
Parallel/Printer, Device Config, Display, CPU, Boot Priority, Keyboard, LAN and USB. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Some models are not equipped with Parallel/Printer tab and/or CPU tab.
Page 130: User Password
General This window displays the BIOS version and contains two buttons: Default and About. Default About Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Registered To enter a user password:...
Page 131 To delete a user password: 1. Select Not Registered to display the following prompt: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. If you click the OK button before entering the password, Registered will appear on the display.
Page 132: Device Config
Device Config Device Configuration This option lets you set the device configuration. All Devices Setup by OS Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted.
Page 133: Boot Priority
Always High Always Low Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD- ROM −> LAN FDD −> HDD −> CD- ROM −> LAN HDD −> CD-ROM −> LAN −>...
Page 134 HW Setup. Support of PC (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. A PC (ATA) card takes the position of HDD in the Boot Priority Options list.
Page 135 HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD −> PC Card(Default) PC Card −>...
Page 136 Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enabled Disabled Enables the Wake-up on Keyboard.
Page 137 Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Disabled Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
Page 138 HW Setup and Passwords 7-10 User’s Manual...
Page 139: Optional Devices
TECRA A2 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory PC card Memory expansion Power devices Additional battery pack...
Page 140: Pc Card
The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.
Page 141: Removing A Pc Card
Removing a PC card Before removing a PC card, make sure that any applications or system services do not use the card. Be sure to disable the PC card prior to removing it. Otherwise, the system may be fatally damaged. To remove the PC card, follow the steps below.
Page 142 Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a. The computer is turned on.
Page 143: Installing Memory Module
Installing memory module Follow the steps below to install a memory module. 1. Set the computer to boot mode and turn off the power. 2. Remove all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack (refer to Chapter6, 4.
Page 144: Removing Memory Module
8. Push the module down so it lies flat. Latches on either side will click into place to secure the module. 9. Seat the cover and secure it with a screw. 10. Replace the battery pack as described in Chapter 6, Modes.
Page 145: Additional Battery Pack
5. Grasp the module by the sides and pull it out. If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. Or you will get burnt if you touch any of them.
Page 146: Battery Charger
Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two lithium ion battery packs. USB Floppy disk drive The 3 1/2" external Floppy disk drive module can be connected to the USB port.
Page 147: Advanced Port Replicator Iil
7. Turn on the computer. 8. Start the HW Setup program. Refer to Chapter 7, Passwords. 9. Select the Parallel/Printer tab from the TOSHIBA HW Setup window. 10. Set the Parallel Port Mode and press OK. 11. Choose Reboot for the change to take effect.
Page 148: Connecting The Port Replicator
The following ports and accessories are available on the Advanced Port Replicator III. RJ45 LAN jack RJ11 Modem jack External monitor port Parallel port Serial port PS/2 mouse port PS/2 keyboard port DC IN 15V socket Security lock slot Audio line-in, line-out jacks Universal Serial Bus (four) IEEE 1394 port (This port is not supported by the computer.) DVI port (This port is not supported by the computer.)
Page 149: Security Lock
Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot.
Page 150 Optional Devices 8-12 User’s Manual...
Page 151: Troubleshooting
TECRA A2 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.
Page 152: Preliminary Checklist
Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. Make sure you turn on all peripheral devices before you turn on the computer.
Page 153: Hardware And System Checklist
Software Hardware Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals. Basic problems may occur in the following areas: System start-up Self test Power Password Keyboard LCD panel Hard disk drive CD-ROM drive DVD-ROM drive DVD-ROM&CD-R/RW drive DVD-R/-RW drive...
Page 154: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: The computer stops and does not proceed to display information or messages except the TOSHIBA logo.
Page 155: Ac Power
Computer shuts down and its DC IN 15V indicator is flashing in green AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN 15V indicator. Refer to Chapter 6, Modes for more information. Problem AC adaptor doesn’t power the computer...
Page 156: Real Time Clock
Problem Battery doesn’t power the computer as long as expected Real Time Clock Problem The following message is Displayed on the LCD: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. After configuring the time and date for the Real Time Clock battery, we recommend that you turn the power status of your computer to "ON"...
Page 157: Password
Password Problem Cannot enter or forgot password For information on setting a password, refer to Chapter 7, Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Problem Some letter keys produce numbers Output to screen is garbled LCD panel...
Page 158: Hard Disk Drive
Hard disk drive Problem Computer does not boot from hard disk drive Slow performance CD-ROM drive For more information, refer to Chapter 4, Problem You cannot access a CD/ DVD in the drive Procedure Check if a floppy disk is in the floppy disk drive. If a floppy disk is inserted, remove it and reboot.
Page 159: Dvd-Rom Drive
Problem Some CDs run correctly, but others do not DVD-ROM drive For more information, refer to Chapter 4, Problem You cannot access a CD/ DVD in the drive Some CD/DVDs run correctly, but others do not User’s Manual Procedure The software or hardware configuration may be causing a problem.
Page 160 Problem 9-10 Procedure Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD- ROM Mode 1, Mode 2, CD- ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD- EXTRA), CD-G (Audio CD only), Addressing Method 2 Check the region code on the DVD.
Page 161: Dvd-Rom&Cd-R/Rw Drive
DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Problem You cannot access a CD/DVD in the drive Some CD/DVDs run correctly, but others do not User’s Manual Operating Procedure Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.
Page 162: Dvd-R/-Rw Drive
9-12 Procedure If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.
Page 163 Chapter 2, The Grand Tour. If you have trouble writing, make sure you are observing the following precautions: Use only media recommended by TOSHIBA. Do not use the mouse or keyboard during writing. Use only the software supplied with the computer for recording.
Page 164: Dvd Super Multi Drive
DVD Super Multi drive For more information , refer to Chapter 4, Problem You cannot access a CD/DVD in the drive Some CD/DVDs run correctly, but others do 9-14 Operating Procedure Make sure the drive's drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD isproperly seated.
Page 165: Floppy Disk Drive
Floppy disk drive For more information, refer to Chapter 4, Problem Drive does not operate There may be a faulty cable connection. Check Some programs run correctly but others do You cannot access the external 3 1/2" floppy disk drive PC card Refer also to Chapter 8, Problem...
Page 166: Pointing Device
Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem On-screen pointer does not respond to Pad operation Double-tapping does not work The mouse pointer moves too fast or too slow When the reaction of...
Page 167: Usb
USB mouse Problem On-screen pointer does not respond to mouse operation Double-clicking does not work The mouse pointer moves too fast or too slow The mouse pointer moves erratically Refer also to your USB device’s documentation. Problem USB device does not work User’s Manual Procedure...
Page 168: Memory Expansion
Memory expansion Refer also to Chapter 8, memory modules. Problem You hear a pattern of beeps. (Two beeps: a long beep followed by a short beep, indicates there is a defective memory module in slot Three beeps: a long beep followed by two short beeps indicates there is a defective memory module in slot...
Page 169: Sound System
The computer will not start and the following sequence of beeps sounds:Long, short, no sound, long, short, short, ... The computer will not start and no beeps are heard. The computer starts but does not detect memory. Sound system Refer also to documentation for your audio devices. Problem No sound is heard Monitor...
Page 170: Modem
Modem Refer to Appendix C, Problem Communication software can’t initialize modem You can hear a dial tone but can’t make a call You place a call, but a connection can’t be made After making a call you can’t hear a ring Communication is cut off unexpectedly A CONNECT display is...
Page 171: Lan
Problem Cannot access LAN Wake-up on LAN does not work Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Problem Cannot access Wireless LAN User’s Manual Procedure Check for a firm cable connection between the...
Page 172: Printer
Printer error TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
Page 173: Where To Write
Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W.
Page 174 Irvine, California 92618 9-24 In Europe United Kingdom TOSHIBA Information Systems (U.K.) Ltd. TOSHIBA Court Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany User’s Manual...
Page 175: Appendix A Specifications
TECRA A2 Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) Size Environmental Requirements Conditions Operating Non-operating Thermal Gradient Wet-bulb temperature Conditions User’s Manual Appendix A 2.6 kilograms, configured with: 14"XGA, 512MB × 1 RAM, 30GB HDD, CD-ROM drive, modem, LAN (100M Bit), 6cell battery.
Page 176: Power Requirements
Operating Non-operating Power Requirements AC adaptor Computer Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing Control command Monitor function Communication specifications Communication system Communication protocol -60 to 3,000 meters -60 to 10,000 meters maximum 100-240 volts AC 50 or 60 hertz (cycles per second)
Page 177 Communication speed Transmitting level Receiving level Input/output impedance Error correcting Data compression Power supply User’s Manual Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/ 37333/38666/40000/41333/42666/44000/45333/ 46666/48000/49333/50666/52000/53333/54666/ 56000 bps 2400/4800/7200/9600/12000/14400 bps -10 dBm -10 to -40 dBm 600 ohms ±30% MNP class 4 and ITU-T V.42 MNP class 5 and ITU-T V.42bis...
Page 178 Specifications User’s Manual...
Page 179: Appendix B Display Controller And Modes
TECRA A2 Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the internal LCD and external monitors.
Page 180 Table1 Video modes (VGA) Video Type Resolution Character mode 0, 1 40 × 25 Text Characters 2, 3 80 × 25 Text Characters 0*, 1* 40 × 25 Text Characters 2*, 3* 80 × 25 Text Characters 0+, 1+ 40 × 25 Text Characters 2+, 3+...
Page 181 Table1 Video modes (VGA) continued Video Type Resolution Character mode 320 × 200 Grph Pels 640 × 200 Grph Pels 640 × 350 Grph Pels 640 × 350 Grph Pels 640 × 480 Grph Pels 640 × 480 Grph Pels 320 ×...
Page 182 Table 2 Video modes (855GME) Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with XGA Panel only) 1400 × 1050 (Virtual with XGA Panel only) 1600 × 1200 1920 × 1440 2048 × 1536 Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode.
Page 183 Table 2 Video modes (855GME) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with XGA Panel only) 1400 × 1050 (Virtual with XGA Panel only) 1600 × 1200 1920 × 1440 2048 × 1536 Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode.
Page 184 Table 2 Video modes (855GME) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with XGA Panel only) 1400 × 1050 (Virtual with XGA Panel only) 1600 × 1200 1920 × 1440 2048 × 1536 Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode.
Page 185 Table 3 Video modes (852GM) Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with XGA Panel only) 1400 × 1050 (Virtual with XGA Panel only) 1600 × 1200 1920 × 1440 Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode.
Page 186 Table 3 Video modes (852GM) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with XGA Panel only) 1400 × 1050 (Virtual with XGA Panel only) 1600 × 1200 1920 × 1440 Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode.
Page 187 Table 3 Video modes (852GM) continued Resolution 640 × 480 800 × 600 1024 × 768 1280 × 1024 (Virtual with XGA Panel only) 1400 × 1050 (Virtual with XGA Panel only) 1600 × 1200 1920 × 1440 Some SVGA modes are not supported at LCD+CRT simultaneous mode and LCD+CRT Multi Monitor mode.
Page 188: Display Settings
Display Settings 1. 1.You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display at the same time. The [Settings] tab is displayed in the following steps; Open [Control Panel], click [Appearance and Themes] Click [display] Select [Settings] tab...
Page 189 FigureB-2 Intel® 82852/82855 GM/GME Graphics Controller Prope... 2. Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same. Reduce the resolution, use the display of the computer only, use the CRT display only or set display device in the multi-monitor, then play DVD.
Page 190 The following [Set up] screen is displayed, then remove the check of [Use Hardware Decode Acceleration] (The check of [Use Hardware Color Acceleration]is removed automatically). Click [OK] button(The [Set up] tab closes automatically). 4. The DVD video overlay is not displayed when the display mode of CRT display is set to high resolution and hifh refresh rate mode at LCD/CRT simultinous or multi-monitor.
Page 191 (external LCD). To configure this setting, install "TOSHIBA Display Service for Ext.Monitor" and restart the machine in the following manner. a. Select the "TOSHIBA Application Installer" from the icon or start menu on a desktop. b. Since "TOSHIBA Application Installer" window starts and click the Next button.
Page 192 Display Controller and Modes B-14 User’s Manual...
Page 193: Appendix C At Commands
TECRA A2 AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
Page 194 Communication standard setting This command determines the communication standard CCITT or Bell. Result Codes: ERROR Otherwise Dial This command instructs the modem to dial a telephone number. Enter n (the telephone number and any modifiers) after the ATD command. Any digit or symbol (0-9, *, #, A, B, C, D) may be dialed as touch-tone digits.
Page 195 Result Codes: ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Result Codes: ERROR Otherwise Request ID information This command displays product information about the modem. Result Codes: ERROR Otherwise Monitor speaker volume...
Page 196 Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. Result Codes: ERROR Otherwise Return on-line to data mode Result Codes: ERROR Otherwise Select pulse dialing...
Page 197 Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
Page 198 Dial tone detect Disabled:The modem dials a call regardless of whether it detects a dial tone. Enabled:The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. Busy tone detect Disabled:The modem ignores any busy tones it receives.
Page 199 &D2 &D3 Result Codes: ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory. This operation replaces all of the command options and the S- register settings in the active configuration with factory values. &F &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while...
Page 200 &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 &T1 Result Codes: CONNECT n=1 ERROR &V Display Current Configuration This command displays the current configuration of the modem. If nonvolatile memory is supported the stored profiles are displayed as well.
Page 201 Result Codes: ERROR Otherwise Local flow control selection Result Codes: ERROR Otherwise Protocol result code Result Codes: ERROR Otherwise View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
Page 202 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
Page 203: Appendix D S-Registers
TECRA A2 S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
Page 204 Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range:0-225 Default:0 Units:rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
Page 205 Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
Page 206 Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range:0-255 Default:2 Units:seconds...
Page 207 S37 Dial line rate S37 = 0 (default) S37 = 1 S37 = 2 S37 = 3 S37 = 4 S37 = 5 S37 = 6 S37 = 7 S37 = 8 S37 = 9 S37 = 10 S37 = 11 S37 = 12 S37 = 13 S37 = 14...
Page 208: At Command Set Result Codes
AT command set result codes The following table shows the result codes. The result code summary Result Code CONNECT RING NO CARRIER ERROR CONNECT 1200 EC* NO DIAL TONE BUSY NO ANSWER CONNECT 2400 EC* CONNECT 4800 EC* CONNECT 9600 EC* CONNECT 14400 EC* CONNECT 19200 EC* CONNECT 7200 EC*...
Page 209 CONNECT 33600 EC* DELAYED* BLACKLISTED* BLACKLIST FULL* *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
Page 210 S-registers User’s Manual...
Page 211 TECRA A2 V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
Page 212 Result code CONNECT 32000 EC* CONNECT 36000 EC* CONNECT 40000 EC* CONNECT 44000 EC* CONNECT 48000 EC* CONNECT 52000 EC* CONNECT 56000 EC* CONNECT 28000 EC* CONNECT 29333 EC* CONNECT 30666 EC* CONNECT 33333 EC* CONNECT 34666 EC* CONNECT 37333 EC* CONNECT 38666 EC* CONNECT 41333 EC* CONNECT 42666 EC*...
Page 213 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis NoEC AT Command -V90=* -V90=0 -V90=1...
Page 214 V.90 User’s Manual...
Page 215: Internal Modem Guide
TECRA A2 Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem The internal modem is preinstalled.
Page 216: Removing The Internal Modem
Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3. Turn the computer upside down and remove the battery pack. 4.
Page 217: Card Specifications
TECRA A2 Wireless LAN Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol Data Rate Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations.
Page 218 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 219 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Page 220 Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID *3 These channels are available to A/B/G combo type only. *4 Available Area: US (USA, CANADA) only 5765* 5785* 5805* 5150-5850 MHz 5210* 5250* 5290* 5760* 5800* US only * US only * US only * Note US only *...
Page 221: Ac Power Cord And Connectors
TECRA A2 AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following...
Page 222 France: Germany: In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.
Page 223: Parts Numbers
TECRA A2 Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD and communication devices. Configurations The following table shows the computer configuration indicated on a label.
Page 224 30GB 40GB 60GB 80GB *Figures indicate the CPU operating speed in megahertz. For example, PM 1.5 means Mobile Intel® Pentium-M processor 1.5GHz. Communication Parallel / No S-Video / 1394 / USB × 2 Parallel / No S-Video / No 1394 / USB × 2 No Parallel / S-Video / 1394 / USB ×...
Page 225 TECRA A2 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange...
Page 226 LED: light emitting diode LSI: large scale integration MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics array plus...
Page 227 application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games. ASCII: American Standard Code for Information Interchange. ASCII code is a set of 256 binary codes that represent the most commonly used letters, numbers, and symbols.
Page 228 cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
Page 229 components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.
Page 230 dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk.
Page 231 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 232 HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel. In Windows, an icon represents an object that the user can manipulate.
Page 233 level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing- side coating is etched into character forming segments with leads that extend to the edge of the glass.
Page 234 nonvolatile memory: Memory, usually read-only (ROM), that is capable of permanently storing information. Turning the computer’s power off does not alter data stored in nonvolatile memory. numeric keypad overlay: A feature that allows you to use certain keys on the keyboard to perform numeric entry, or to control cursor and page movement.
Page 235 Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached. The board itself is typically flat and rectangular, and constructed of fiberglass, to form the attachment surface.
Page 236 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Page 237 warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. write protection: A method for protecting a floppy disk from accidental erasure.
Page 238 Glossary Glossary-14 User’s Manual...
Page 239 Display 1-6 automatic power off 1-9 brightness decreases 5-5 brightness increases 5-5 controller 1-6 hinge 2-8 opening 3-7 DLA for TOSHIBA 1-13 Documentation list 1-2 DVD Super Multi drive 1-6 location 2-3 using 4-3 writing 4-8 DVD-R/-RW drive 1-6 location 2-3...
Page 240 placement 3-2 Ergonomics lighting 3-3 seating and posture 3-3 work habits 3-4 Floppy disk 1-4 using 4-2 Fn + Ctrl (enhanced keyboard’s simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-3 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-4 Fn + F4 (hibernation) 5-4...
Page 241 Password 9-7 PC card 9-15 Pointing device 9-16 Power 9-4 Real Time Clock 9-6 Self test 9-4 Sound system 9-19 Support from TOSHIBA 9- System start-up 9-3 USB 9-17 Wireless LAN 9-21 RecordNow 1-12 RecordNow! 1-12 4-12 Recovery HDD 3-13...
Page 242 5-3 speakers 2-8 volume control 2-3 Standby 1-11 setting 3-10 System automatic 1-10 TOSHIBA ConfigFree 1-13 TOSHIBA PC DiagnosticTool 1- TOSHIBA Power Saver 1-12 TOSHIBA Utilities 1-9 TOSHIBA Zooming Utility 1-12 Touch Pad 1-7 control buttons 2-8 location 2-7...

Toshiba TECRA A2 User Manual

Quick Links

Related Manuals for Toshiba TECRA A2

Summary of Contents for Toshiba TECRA A2

Table of Contents