1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Portege M200
  6. User manual

Toshiba Portégé M200 User Manual

Toshiba notebook computer user's manual
Hide thumbs Also See for Portégé M200:
Table of Contents

Advertisement

Quick Links

Download this manual
Portégé
User's Manual
M200
ORTÉGÉ M200
PORTÉGÉ M200
PORTÉGÉ M200
Choose freedom.
Choose freedom.
Choose freedom.
computers.toshiba-europe.com

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Portégé M200

Summary of Contents for Toshiba Portégé M200

  • Page 1 Portégé User’s Manual M200 ORTÉGÉ M200 PORTÉGÉ M200 PORTÉGÉ M200 Choose freedom. Choose freedom. Choose freedom. computers.toshiba-europe.com...
  • Page 2 Intel Corporation. Windows and Microsoft are registered trademarks of Microsoft Corporation. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under licence. Other trademarks and registered trademarks not listed above may be used in this manual.
  • Page 3 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

  • Page 4: General Precautions

    General Precautions TOSHIBA computers are designed to optimise safety, minimise strain and withstand the rigours of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
  • Page 5 For optimum performance, use your computer product only under recommended conditions Read additional restrictions under “Environmental Conditions” in your product Resource Guide. Contact TOSHIBA Service and Support for more information. Portégé M200 User's Manual...

  • Page 6: Cooling Fan

    Cooling fan This product is equipped with a CPU cooling fan, VGA cooling fan and vent holes. Please make sure to follow the cautions below to avoid overheat. ■ Clean any dust or dirt that has accumulated on the CPU cooling fan, VGA cooling fan or vent holes.

  • Page 7: Working Environment

    This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments".
  • Page 8 User's Manual Network connection (class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding may suffer interference.

  • Page 9: Table Of Contents

    Portégé M200 Table of Contents Preface ... xvi Manual contents... xvi Conventions... xvii Abbreviations...xvii Icons ...xvii Keys...xvii Key operation ... xviii Display ... xviii Messages ... xviii Chapter 1 Equipment checklist ...1 1 Features ...1 3 Special features...1 7 Utilities ...1 10 Options...1 13 Chapter 2 The Grand Front with the display closed ...2 1...
  • Page 10 Removing the Reserve Pen ...4 7 Changing to the Tablet mode...4 8 Changing the screen orientation ...4 11 Method 1: Changing the screen orientation using TOSHIBA Accelerometer Utilities...4 12 Method 2: Changing the screen orientation using Cross Function Button ...4 12 Method 3: Changing the screen orientation using Task Bar...4 13...
  • Page 11 Wireless communications ...4 17 Wireless LAN ...4 17 Bluetooth wireless technology...4 18 Wireless communication switch ...4 18 Wireless communication indicator...4 19 LAN ...4 19 LAN cable types ...4 20 Connecting LAN cable...4 20 Disconnecting LAN cable ...4 21 Using the microphones...4 21 Audio ...4 22 Using the internal modem ...4 25 Region selection ...4 25...
  • Page 12 Extending battery life...6 10 Replacing the Battery Pack...6 11 Removing the Battery Pack ...6 11 Installing the Battery Pack ...6 13 TOSHIBA Password Utility...6 14 User password ...6 14 Supervisor password...6 15 Starting the computer by password ...6 16 Tablet mode ...6 16 Power up modes ...6 17...
  • Page 13 Chapter 8 Optional Devices Cards/memory...8 1 Power devices ...8 1 Peripheral devices ...8 1 Other...8 1 PC cards...8 2 Inserting a PC card ...8 2 Removing a PC card...8 3 SD cards...8 3 Installing an SD card...8 4 Removing an SD card...8 4 Formatted SD Cards ...8 5 Creation of a boot disk ...8 6 Memory expansion...8 6...
  • Page 14 Chapter 9 Troubleshooting Problem solving process ...9 1 Preliminary checklist...9 2 Analysing the problem ...9 2 Hardware and system checklist...9 3 System start up ...9 4 Self test...9 4 Power ...9 4 Password...9 7 Keyboard ...9 7 LCD panel...9 7 Hard disk drive ...9 8 Diskette drive...9 8 Infrared port...9 9...
  • Page 15 Table of Contents Appendix A Specifications ... A 1 Appendix B AC Power Cord and Connectors ... B 1 Appendix C Keyboard Layouts ...C 1 Appendix D Display Controller and Modes ...D 1 Appendix E If your computer is stolen... E 1 Appendix F ASCII Character Codes ...

  • Page 16: Preface

    Portégé M200 Preface Congratulations on your purchase of the TOSHIBA Portégé M200 computer. This powerful, light weight notebook computer is designed to provide years of reliable, high performance computing. This manual tells how to set up and begin using your Portégé M200 computer.

  • Page 17: Conventions

    Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power Up Modes, gives details on the computer’s power resources and battery save modes and how to set a password. Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program.

  • Page 18: Key Operation

    Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.

  • Page 19: Chapter 1 Introduction

    This chapter provides an equipment checklist, and it identifies the computer’s features, utilities and options. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Hardware Carefully unpack your computer.
  • Page 20 TOSHIBA Modem driver ■ TOSHIBA Display driver ■ TOSHIBA Touch Pad driver ■ TOSHIBA Sound driver ■ TOSHIBA Bluetooth drivers (Can be used only in Bluetooth models) ■ TOSHIBA Wireless LAN Driver ■ TOSHIBA Mobile Extension3 ■ TOSHIBA Utilities ■...

  • Page 21: Features

    Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built in...

  • Page 22: Touch Pad

    Disks Built in Display The computer’s LCD panel supports high resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built in Gaphics controller Keyboard Built in Touch pad Built in Tablet PC Pen Supplied Reserve Pen...
  • Page 23 Power Battery Pack RTC battery AC adaptor Ports Headphone Microphone Infrared External monitor Docking Universal Serial Bus (USB 2.0) Slots PC card SD card Portégé M200 The computer is powered by one rechargeable lithium ion battery pack. The internal RTC battery backs up the Real Time Clock (RTC) and calendar.
  • Page 24 Multimedia Sound System Communications Modem Wireless LAN Wireless communication switch Bluetooth Portégé M200 Windows Sound System compatible sound system provides internal speakers and an internal microphone as well as jacks for an external microphone and headphone. An internal modem provides capability for data and fax communication.

  • Page 25: Special Features

    Security lock slot Software Operating System TOSHIBA Utilities Plug and Play Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Keypad overlay Display automatic power off...
  • Page 26 System Standby or System Hibernate in the System standby and System hibernation item of the Basic Setup tab in TOSHIBA Power Saver. This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Profile item in TOSHIBA Power Saver.
  • Page 27 Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on fan first, then if...

  • Page 28: Utilities

    To start the utility, open the Control Panel, click Printers and Other Hardware and click the TOSHIBA HW Setup icon. The TOSHIBA Password Utility provides two levels of password security: User and Supervisor.
  • Page 29 Stand by or Hibernation. Settings can be modified from the "TOSHIBA Mobile Extension 3" icon in the TOSHIBA Console. This utility lets you display or hide a confirmation message when you press Fn + F3 or Fn + F4.
  • Page 30 Stack Bluetooth cannot be used in models that do not have a Bluetooth module installed. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to TOSHIBA SD Memory Boot Utility Drag’n Drop CD+DVD The setup image for Drag'n Drop CD+DVD is Portégé...

  • Page 31: Options

    This option enables Bluetooth wireless communications in computer that does not have preinstalled Bluetooth. It is installed by dealers only. Tablet PC Pen can be purchased from your TOSHIBA dealer. Use it as a spare to your computer. Introduction 1 13...
  • Page 32 TOSHIBA dealer. External CD RW/DVD RW is an optional accessory compatible with USB 2.0 port on this computer. You can buy the drive from TOSHIBA dealer. Bluetooth SD card is an optional accessory compatible with the SD Card slot of this computer.

  • Page 33: Chapter 2 The Grand Tour

    Portégé M200 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The figure below shows the computer’s front with its display panel in the closed position.

  • Page 34: Left Side

    Volume control SD card slot Keep foreign objects out of the SD card slot. A pin or similar object can damage the computer’s circuitry. SD card indicator Display latch button Docking holes Left side The figure below shows the computer’s left side. SECURITY LOCK SLOT Security lock slot PC card slot...

  • Page 35: Right Side

    On Off Wireless communication switch Set the switch to off in airplanes and hospitals. Check the wireless communication indicator. It will stop glowing when the wireless communication function is off. Infrared port Right side The figure below shows the computer’s right side. Tablet PC Pen Tablet PC Pen slot Security lock slot...

  • Page 36: Back Side

    Back side The figure below shows the computer’s back side. DC IN 15V USB PORTS CPU cooling fan vent This cooling fan in takes air to cool CPU. Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vent.

  • Page 37: Underside

    Link indicator Modem jack In case of a lightning storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem. Underside The figure below shows the underside of the computer. Make sure the display is closed before turning over your computer.
  • Page 38 Chapter 6, Power and Power Up Modes, describes how to access the Battery Pack. Battery Packs can be purchased from your TOSHIBA dealer to extend the computer’s battery operating time. The battery lock prevents inadvertent release of the Battery Pack.

  • Page 39: Front With The Display Open

    Front with the display open DISPLAY DISPLAY SCREEN LATCH POWER BUTTON POWER BUTTON LOCK Display latch Portégé M200 CROSS MICRO FUNCTION PHONES PEN ICONS BUTTON POWER SOURCE/ DISPLAY HINGE SPEAKER SYSTEM INDICATORS The front with the display open The Display latch secures the Display screen in its closed position.

  • Page 40: Ac Adaptor 2

    Display screen Display hinge Microphones Power button Power button lock Power source/ system indicators Sensor switch Touch pad Touch pad control buttons Windows Security tablet button Cross Function button Portégé M200 The full colour LCD displays high contrast text and graphics and is compatible with the industry standard Video Graphics Array (VGA).
  • Page 41 Speaker ESC/Rotation button Pen Icons Pen Button 1 Pen Button 2 Pen Button 3 Pen Button 4 Portégé M200 The speaker emits sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Press this button more than one second to change the orientation of the screen.

  • Page 42: Indicators

    Indicators The figure below shows the indicators, which light when various computer operations are in progress. DC IN 15V WIRELESS COMMUNI CATION Portégé M200 POWER BATTERY The power source/system indicators (laptop mode) DISK BATTERY The power source/system indicators (tablet mode) The Grand Tour DISK WIRELESS...

  • Page 43: Power Source/System Indicators

    Power source/system indicators DC IN 15V Power Battery Disk Wireless communication The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows, the keypad overlay lets you control the cursor. When the F11 key indicator glows, the keypad overlay lets you enter numbers.

  • Page 44: Keyboard Indicator

    When the CapsLock indicator glows, the keyboard is in all caps mode. Keyboard indicator Caps Lock Arrow mode Numeric mode Portégé M200 CAPS LOCK CapsLock indicator This indicator glows green when the alphabet keys are locked in uppercase. When the Arrow mode indicator glows green, you can use the keypad overlay (white labelled keys) as cursor keys.

  • Page 45: Ac Adaptor

    Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. Portégé M200 The AC adaptor...

  • Page 46: Chapter 3 Getting Started

    Portégé M200 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 47: General Conditions

    General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.

  • Page 48: Seating And Posture

    Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to the figure below. ■...

  • Page 49: Work Habits

    Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency.

  • Page 50: Operating The Computer In Tablet Mode

    Operating the computer in tablet mode TOSHIBA Portégé M200 computer can be used in two ways; ordinary laptop PC and tablet PC. You can use the computer as tablet PC that is operated with attached Tablet PC Pen by turning LCD panel in 180 degrees and closing it.

  • Page 51: Connecting The Ac Adaptor

    Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual.
  • Page 52 1. Connect the power cord to the AC adaptor. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V port on the back of the computer. DC IN 15V PORT 3. Plug the power cord into a live wall outlet. The Battery and DC IN 15V indicator on the front of the computer should glow.

  • Page 53: Opening The Display

    Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Push down the display latch on the front of the computer to unlatch the display panel. 2. Lift the display panel up and adjust it to the best viewing angle for you.

  • Page 54: Turning On The Power

    Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter.

  • Page 55: Turning Off The Power

    Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode, no data is saved and the computer will boot to the operating system’s main screen.
  • Page 56 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.

  • Page 57: Standby Mode

    When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. To restore operation from Standby mode, slide the power button or press any key.
  • Page 58 1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.

  • Page 59: Restarting The Computer

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the left or right cursor key to select the CD ROM icon in the display menu.

  • Page 60: Chapter 4 Operating Basics

    Portégé M200 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the Tablet PC Pen, the external diskette drive, the wireless communication, LAN and the internal modem. It also provides tips on caring for your computer and on heat dispersal. Using the Touch Pad To use the Touch Pad, simply press and move your finger tip across it in the direction you want the on screen pointer to go.

  • Page 61: Using The Tablet Pc Pen And Reserve Pen

    For some functions, you can tap the touch pad instead of pressing a control button. Click Double click Drag and drop Scroll Using the Tablet PC Pen and Reserve Pen Eraser button Pen button Pen point ERASER BUTTON PEN POINT Portégé...
  • Page 62 Do not use a broken pen tip The lead cannot be replaced if it is worn. (Reserve Pen only). TOSHIBA is not liable to the quality problem of the products due to the use of the Tablet PC Pen in an environment where above conditions are not satisfied because of the use by unspecified number of users.

  • Page 63: Inserting The Tablet Pc Pen

    Inserting the Tablet PC Pen TABLET PC PEN SLOT The Tablet PC Pen is included in the product when purchased. Take out the Tablet PC Pen from the carton and install it to the computer as the following. 1. Insert the Tablet PC Pen into the pen holder until it clicks. The Tablet PC Pen and the emergency Tablet PC Pen are different in shape.

  • Page 64: Pen Actions

    Operating Basics Pen actions You can use the Tablet PC Pen to enter data, start programs, move objects and execute other actions. Single tap Lightly tap the tip of the Tablet PC Pen on an object and lift it immediately to execute an action.

  • Page 65: Replacing The Pen Tip

    Short and worn pen point is difficult to pull out. Replace the pen point with refill before it becomes too short. TOSHIBA recommends the customer to keep another pen set as a spare. You can buy the pen set from TOSHIBA dealer.

  • Page 66: Inserting The Reserve Pen

    Inserting the Reserve Pen 1. Remove the Battery Pack. 2. Gently push the Reserve Pen into the pen holder to insert it. 3. Reinstall the Battery Pack. Refer to the Replacing the Battery Pack section in Chapter 6,Power and Power Up Modes for more information on how to remove and reinstall the Battery Pack.

  • Page 67: Changing To The Tablet Mode

    Changing to the Tablet mode To change the laptop mode to the tablet mode, follow the instructions below. Place the computer on a stable, flat place such as a desktop and rotate the display panel slowly, holding the panel at its lower part. The display panel is designed not to rotate more than 180 degrees.
  • Page 68 1. Open the display panel to the upright position. 2. Rotate the display panel clockwise slowly. Do not apply excessive rotating force to the display panel. It causes damage of the display panel. Portégé M200 Changing to the Tablet mode (2) DISPLAY LATCH Changing to the Tablet mode (3) Operating Basics...
  • Page 69 Operating Basics 3. Turn the Display latch in 180 degrees to the down side. 4. Close the display panel slowly with LCD surface outside. DISPLAY LATCH SLIT Changing to the Tablet mode (4) 5. Turn the Display latch downward. 6. Insert the Display latch in the slit. 7.

  • Page 70: Changing The Screen Orientation

    Changing the screen orientation The orientation of desktop screen can be changed to one of the following four display modes: Execute the following applications on Primary landscape: 3D game software 3D screen saver Playback of motion picture, such as a case of DVD Video playback on the computer connecting an external DVD ROM Drive.

  • Page 71: Method 1: Changing The Screen Orientation Using Toshiba Accelerometer Utilities

    The computer is shaken horizontally. Method 2: Changing the screen orientation using Cross Function Button 1. Press Cross Function Button for more than one second. TOSHIBA Table Menu will appear. 2. Select the internal Display of the TOSHIBA shortcut using Cross Function Button and press Cross Function Button.

  • Page 72: Method 3: Changing The Screen Orientation Using Task Bar

    Click "OK" button. You can set the orientation of the desktop screen just after rotating the display from Start > All Programs > TOSHIBA > Tablet PC > TOSHIBA Rotation Utility Changing to the laptop mode To change the Tablet mode to the laptop mode, follow the instructions below.

  • Page 73: Using The Usb Fdd Kit

    Using the USB FDD Kit A 3 ½" diskette drive connects to the computer’s USB port. It accommodates 1.44 megabyte or 720 kilobyte diskettes. Refer to the Options section in Chapter 1, Introduction for more information. The USB FDD Kit is an option with some models. USB CONNECTOR DISK IN USE INDICATOR...

  • Page 74: Connecting The Usb Diskette Drive

    Operating Basics The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20° while it is operating. Do not set anything on top of the diskette drive. If you need to boot the computer from the diskette drive or if you use an OS that does not support USB, you must set the USB FDD Legacy Emulation feature in HW Setup to Enabled.

  • Page 75: Disconnecting The Usb Diskette Drive

    Disconnecting the USB diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive.

  • Page 76: Wireless Communications

    Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. In this chapter, the descriptions on Wireless LAN or Bluetooth are applicable to the model equipped with Wireless LAN or Bluetooth function respectively. Carefully check that the computer is available for Wireless LAN communication in Tablet mode.

  • Page 77: Bluetooth Wireless Technology

    Wireless LAN to cause illegal intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA strongly recommend the customer to enable the WEP function. Bluetooth wireless technology BluetoothTM wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones.

  • Page 78: Wireless Communication Indicator

    Wireless communication indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indicator off Indicator glows If you used the Task Bar to disable W LAN, restart the computer or follow the procedures below to enable the system to recognize W LAN. Open or click the following: start, Control Panel, System, Hardware Device Manager, Network adaptors, Atheros AR5001X+ Wireless Network Adaptor and enable.

  • Page 79: Lan Cable Types

    LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE TX), be sure to connect with a CAT5 cable.

  • Page 80: Disconnecting Lan Cable

    Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer and pull out the connector.

  • Page 81: Audio

    Audio This section describes audio controls including sound levels and power management. Volume control The Volume Control utility lets you control the audio volume in Windows for both playback and recording. ■ To launch Volume Control for playback, click Start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control.
  • Page 82 Operating Basics Microphone Enhancements The Microphone Setup allows you to optimise the microphone input settings for your particular configuration. Choose Standard Microphone if you have an ordinary desktop microphone. Choose Headset if you have a wearable microphone that is positioned directly in front of your mouth. SoundMAX Superbeam™...
  • Page 83 Operating Basics Power management The audio controller can be powered down when the audio function is idle. To enable the Audio Power Management, follow the steps below. 1. Clicked the Power Management tab. 2. Select the Normal Power Savings in the Power Mode pull down list. If the No Power Savings is selected, the audio controller always runs.

  • Page 84: Using The Internal Modem

    1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 85: Properties Menu

    Operating Basics Properties menu Click the icon with the secondary mouse button to display the following menu. Setting You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. Open the Dialling Properties dialog box after selecting region.

  • Page 86: Connecting

    Connecting To connect the internal modem cable, follow the steps below. The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. In case of a lightning storm, unplug the modem cable from the telephone jack.

  • Page 87: Cleaning The Computer

    Cleaning the computer To help ensure long, trouble free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 88: Heat Dispersal

    CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup item in TOSHIBA Power Saver. Maximum performance...

  • Page 89: Chapter 5 The Keyboard

    Portégé M200 The Keyboard The computer’s keyboard layouts are compatible with a 101/102 key enhanced keyboard. By pressing some keys in combination, all the 101/102 key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 90: F1 ... F12 Function Keys 5

    F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed.

  • Page 91: Soft Keys: Fn Key Combinations

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features. Some software may disable or interfere with soft key operations. Soft key settings are not restored by the Resume feature.

  • Page 92: Hotkeys

    The Keyboard Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad. Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key. Hotkeys Hotkeys (Fn + another key) let you enable or disable certain features of the computers.
  • Page 93 The Keyboard Standby: When you press Fn + F3, the computer can enter Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you check the checkbox in the dialog box, it will not appear from the next time. Hibernation: When you press Fn + F4, the computer can enter Hibernation.

  • Page 94: Fn Sticky Key

    2 key while holding down the Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key.

  • Page 95: Windows Special Keys

    Windows special keys The keyboard provides two keys that have special functions in Windows: one activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.

  • Page 96: Numeric Mode

    Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the following figure. Press Fn + F11 again to turn off the overlay. Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1.

  • Page 97: Temporarily Using Overlay (Overlay Off)

    Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry.

  • Page 98: Chapter 6 Power And Power Up Modes

    Portégé M200 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected,...

  • Page 99: Power Indicators

    Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, contact TOSHIBA dealer. Refer to Chapter 9, Troubleshooting. Under any other conditions, the indicator does...

  • Page 100: Power Indicator

    Dispose of the battery as required by local ordinances or regulations. Use only battery recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAMs, so if the computer loses power it will be lost.

  • Page 101: Real Time Clock Battery

    Check system. Then press [F1] key The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
  • Page 102 Danger 1. Never try to dispose of the battery pack by burning or expose it to a heating device such as a microwave oven. The battery pack could explode and cause bodily injury. 2. Never try to disassemble, repair or otherwise tamper with a battery pack.
  • Page 103 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling centre to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short circuits, which could cause the battery pack to ignite or rupture.

  • Page 104: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the Battery Pack. Do not attempt to charge the Battery Pack with any other charger.
  • Page 105 Time The following table shows the approximate time required to fully charge a discharged battery. Battery type Battery pack RTC battery The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.

  • Page 106: Monitoring Battery Capacity

    In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 107: Retaining Data With Power Off

    Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (4400 mAh) RTC battery Extending battery life To maximize the life of your Battery Pack: ■...

  • Page 108: Replacing The Battery Pack

    Replacing the Battery Pack When the Battery Pack reaches the end of its operating life you will need to install a new one. The life of the Battery Pack is generally about 500 recharges. If the Battery indicator flashes in orange shortly after fully recharging the battery, the Battery Pack needs to be replaced.
  • Page 109 6. Slide the battery release latch to free the battery pack for removal. For environmental reasons, do not throw away a spent Battery Pack. Please return spent Battery Packs to your TOSHIBA dealer. Portégé M200 BATTERY RELEASE LATCH BATTERY LOCK...

  • Page 110: Installing The Battery Pack

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Inserts calmly until the battery pack in the connector aslant and there until it clicks.

  • Page 111: Toshiba Password Utility

    TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: Start >...

  • Page 112: Supervisor Password

    If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: Start >...

  • Page 113: Starting The Computer By Password

    Starting the computer by password If you registered a password, there are two ways to start the computer: ■ Insert a password token before you turn on the computer. The computer will start normally, without displaying a password prompt. ■ Enter the password manually.

  • Page 114: Power Up Modes

    Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.

  • Page 115: Chapter 7 Hw Setup

    Portégé M200 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for display, CPU, boot priority, Keyboard, USB, LAN, general and device configuration. HW Setup TOSHIBA HW Setup lets you configure settings for display, CPU, boot priority, Keyboard, USB, LAN, general and device configuration.
  • Page 116 Device Config Device Configuration This option lets you set the device configuration. All Devices Setup by OS Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you set the display to be used when the computer is booted.
  • Page 117 Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD -> FDD -> CD-ROM -> LAN FDD -> HDD -> CD-ROM -> LAN HDD -> CD-ROM -> LAN -> FDD FDD ->...
  • Page 118 This procedure does not affect the settings. Use hot keys. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built in HDD, CD ROM, FDD (or SD memory Card), Network (LAN), PCA (ATA) card boot.
  • Page 119 [RPL] PC card HDD boot is supported only by the PC card slot on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. When you assign a PC card HDD top priority, “PC” is not displayed. However, the PC card HDD takes the position of HDD in the Boot Priority Options list above.
  • Page 120 Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Standby mode. Enabled Disabled USB KB/Mouse Legacy Emulation...
  • Page 121 Wake-up on LAN This features lets the computer’s power be turned on when it receives a wake up signal from the LAN. Enabled Disabled Do not install or remove an optional memory module while Wake up on LAN is enabled. Wake up on LAN does not work without the AC adaptor.

  • Page 122: Chapter 8 Optional Devices

    Portégé M200 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. The following optional devices are available from your TOSHIBA dealer: Cards/memory ■ PC cards ■ SD cards ■ Memory module Power devices ■ Battery Pack ■...

  • Page 123: Pc Cards

    The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16 bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 124: Removing A Pc Card

    Removing a PC card To remove the PC card, follow the steps below: 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5.

  • Page 125: Installing An Sd Card

    Installing an SD card To install an SD card, follow the steps below. 1. Insert the SD card. 2. Press gently to ensure a firm connection. Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below: 1.

  • Page 126: Formatted Sd Cards

    Formatted SD Cards Usually new SD cards are pre formatted before shipping. When you reformat the formatted SD cards, select the Toshiba SD card format as a format type. Formatted SD cards can also be reformatted with devices that use this type of memory card (digital cameras and audio players).

  • Page 127: Creation Of A Boot Disk

    Creation of a boot disk In TOSHIBA SD Memory Boot Utility, a boot disk can be created with SD memory card. Refer to the Utilities section of Chapter 1 for details. Memory expansion This computer is equipped with two memory module sockets; Slot A and Slot B on the underside of the computer.

  • Page 128: Installing Memory Module

    Optional Devices If you install a memory module that is not compatible with the computer, beep will sound when you turn on the power. If the module is installed in slot A, there will be a long beep (1 second) followed by two short beeps (0.5 second each).
  • Page 129 5. Insert the memory module obliquely against the connector of the memory module slot. Gently push the memory module until it is secured in place. The memory module slot consists of two sub slots (connectors): Slot A (lower slot) and Slot B (upper slot). Align the grooves of the memory module with the locking tabs of the connector and insert the module into the difficult to install the memory module, try to adjust the tabs of the...

  • Page 130: Removing Memory Module

    Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Save data, shutdown Windows and turn the power off. 2. Remove the AC adaptor cable and other cables from the computer. 3. Close the display panel and turn the computer over. Remove the Battery Pack.

  • Page 131: Battery Pack

    Battery Pack You can increase the portability of the computer with Battery Packs (PA3191U).. If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power Up Modes.

  • Page 132: Tablet Multi Dock

    Tablet Multi Dock In addition to the ports available on the computer, the Tablet Multi Dock provides, audio line out jack. The Tablet Multi Dock connects directly to the docking interface on the bottom of the computer. The AC adaptor connects the Tablet Multi Dock to a power source.

  • Page 133: External Monitor

    External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3.

  • Page 134: Security Lock

    Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the left side or right side of the computer.

  • Page 135: Chapter 9 Troubleshooting

    Portégé M200 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 136: Preliminary Checklist

    Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 137: Hardware And System Checklist

    Software The problems may be caused by your software or diskette. If you cannot load a software package, the media (usually a diskette) may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.

  • Page 138: System Start

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: If any of the following conditions are present, the self test failed: ■...
  • Page 139 Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Resume mode and shut down. Problem Computer shuts down DC IN 15V indicator blinks orange It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN 15V indicator stops blinking.
  • Page 140 Battery If you suspect a problem with the battery, check the DC IN 15V indicator as well as the Battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power Up Modes. Problem Battery doesn’t power the computer Battery doesn’t charge when the AC adaptor...

  • Page 141: Password

    Password Problem Cannot enter password Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Some letter keys produce numbers Output to screen is garbled LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords, for more information.

  • Page 142: Hard Disk Drive

    Hard disk drive Problem Computer does not boot from hard disk drive Slow performance Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Drive does not operate There may be a faulty cable connection. Check Some programs run correctly but others do You cannot access the external 3 ½"...

  • Page 143: Infrared Port

    Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TOSHIBA tablet pen Problem On screen pointer does not respond to tablet pen operation...
  • Page 144 Touch Pad Problem On screen pointer does not respond to Pad operation Double tapping does not work The mouse pointer moves too fast or too slow Portégé M200 Procedure The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it.

  • Page 145: Pc Card

    USB mouse Problem On screen pointer does not respond to mouse operation Double clicking does not work The mouse pointer moves too fast or too slow The mouse pointer moves erroneously PC card Refer also to Chapter 8, Optional Devices. Problem PC card error occurs Portégé...

  • Page 146: Sd Card

    Make sure the card is not write protected. Make sure the target file is on the SD Card inserted in the slot. If problems persist, contact your dealer. Create a startup disk using the TOSHIBA SD memory boot utility. Refer to Utilities in Chapter 1. Procedure Make sure that the external monitor’s power...

  • Page 147: Sound System

    Sound system Refer also to documentation for your audio devices. Problem No sound is heard Refer also to your USB device’s documentation. Problem USB device does not work Portégé M200 Procedure Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure.

  • Page 148: Memory Expansion

    Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Beep sounds. (If memory is in slot A, a long beep (1 second) followed by two short beeps (0.5 second each). If in slot B, a long beep followed by four short beeps.

  • Page 149: Modem

    Modem Problem Communication software can’t initialise modem You can hear a dial tone but can’t make a call You place a call, but a connection can’t be made After making a call you can’t hear a ring Communication is cut off unexpectedly A CONNECT display is quickly replaced by...

  • Page 150: Lan

    Problem Cannot access LAN Wake up on LAN does not work Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Cannot access Wireless LAN Bluetooth For more information on wireless communication, refer to Chapter 4,...

  • Page 151: Real Time Clock

    Date/Time. If you need further assistance If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call...

  • Page 152: Appendix A Specifications

    Portégé M200 Specifications This appendix summarises the computer’s technical specifications. Physical dimensions Size With TFT display Weight User's Manual Portégé M200 Appendix A 295 (w) × 239 (d) × 36.9 millimeters 2.0 kg typical with 40 GB Hard disk, 256 MB Memory, 12”SXGA+ TFT Display.

  • Page 153: Environmental Requirements

    Environmental Requirements Conditions Operating Non operating Thermal Gradient Wet bulb temperature Conditions Operating Non operating Power Requirements AC adaptor Computer Portégé M200 Ambient Relative humidity temperature 5°C to 35°C 20% to 80% 20°C to 65°C 10% to 90% 20°C per hour maximum 26°C maximum Altitude (from sea level) 60 to 3,000 metres...
  • Page 154 Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialling Control command Monitor function Communication specifications Communication system Communication protocol Communication speed Error correcting Data compression Transmitting level Receiving level Input/output impedance Power supply Portégé M200 Telephone line (analogue only) Pulse Tone...

  • Page 155: Appendix B Ac Power Cord And Connectors

    Portégé M200 AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country in which it is used. All cords must meet the following specifications: Length: Wire size:...
  • Page 156 Italy: The Netherlands: Norway: Sweden: Switzerland: United Kingdom: Japan: In Europe, power cords must be VDE type, H05VVH2 F and two conductor. For the United States and Canada, plug configuration must be a 2 15P (250 V) or 1 15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.

  • Page 157: Appendix C Keyboard Layouts

    Satellite Pro A10 Series Keyboard Layouts Arabic Belgian User's Manual Portégé M200 Keyboard Layouts Appendix C...
  • Page 158 Keyboard Layouts Danish French German Portégé M200...
  • Page 159 Keyboard Layouts Italian Norwegian Portuguese Portégé M200...
  • Page 160 Keyboard Layouts Russian Spanish Swedish Portégé M200...
  • Page 161 Keyboard Layouts Swiss German UK English US English Portégé M200...

  • Page 162: Appendix D Display Controller And Modes

    Portégé M200 Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors.
  • Page 163 Table 1 Video modes (Landscape) Video Type mode 0, 1 Text 2, 3 Text 0*, 1* Text 2*, 3* Text Text Text 4, 5 Grph Grph Text Text Grph Grph Grph Grph Grph Grph Grph Portégé M200 Resolution Character matrix colours (pels) 40 ×...
  • Page 164 Video Type mode SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph Portégé M200 Resolution Character matrix colours (pels) 640 × 480 256 of Pels 256K 800 ×...
  • Page 165 Video Type mode SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph Portégé M200 Resolution Character matrix colours (pels) 1920 × 1440 Pels 2048 × 1536 Pels 640 × 480 16M of Pels 800 ×...
  • Page 166 Table 2 Video modes (Portrait) Video Type mode SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph Portégé M200 Resolution Character matrix colours (pels) 480 × 640 256 of Pels 256K...
  • Page 167 Video Type mode SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph SVGA Grph Portégé M200 Resolution Character matrix colours (pels) 1200 × 1600 Pels 1440 × 1920 Pels 1536 ×2048 Pels 480 ×...

  • Page 168: Appendix E If Your Computer Is Stolen

    What is your address, phone, and fax number? To register the theft, please follow these procedures: ■ Fill in the TOSHIBA Theft Registration form (or a copy of it) on the next page. ■ Attach a copy of your receipt showing where your computer was purchased.

  • Page 169: Toshiba Theft Registration

    TOSHIBA Theft Registration Send to: Fax number: Country stolen: Machine type: (e.g. Portégé M200) Model number: (e.g. PXXXXX YXT) Serial number: (e.g. 70123456E) Date stolen: Warranty seal: (e.g. 9813 123456 049) Owner’s details Name: Company: Street: Postal Code/City: Country: Phone: Fax: Portégé...

  • Page 170: Appendix F Ascii Character Codes

    Portégé M200 ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, The Keyboard). The characters that are printed, however, depend on the software you are using.
  • Page 171 code Portégé M200 Sort code char ¶ § ▲ ▼ ASCII Character Codes Ctrl char...
  • Page 172 code code char space “ & ’ < > Portégé M200 Sort code code ASCII Character Codes Sort char...
  • Page 173 code code char ’ Portégé M200 Sort code code ASCII Character Codes Sort char Ç ü é â ä à å ç ê ë è ï î ì Ä Å É æ Æ ô ö ò û ù ÿ Ö Ü...
  • Page 174 code code char á í ó ú ñ Ñ ¿ ¡ « » Portégé M200 Sort code code ASCII Character Codes Sort char...
  • Page 175 Portégé M200 code code char ß ASCII Character Codes Sort...

  • Page 176: Appendix G Internal Modem Guide

    Portégé M200 Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not remove the base cover except to remove or install the internal modem or to check the PTT label. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described.

  • Page 177: Removing The Internal Modem

    12. Connect the fan cable in a memory slot cover, and seat the memory slot cover. 13. Screw under the battery pack slot with the one screw. 14. Install the battery pack. Removing the internal modem To remove the internal modem. 1.

  • Page 178: Appendix H Wireless Lan

    Portégé M200 Wireless LAN This appendix describes Wireless LAN features and TOSHIBA Wireless LAN card specifications. For details on Wireless LAN settings, refer to the LAN Card Settings and Client Manager help file. These references have the latest information. Card specifications...

  • Page 179: Radio Characteristics

    Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN Wireless networking products have been designed for operation in the license free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
  • Page 180 Subject to the radio regulations that apply in your country, your Wireless LAN Card may support a different set of 2.4GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in your country/region.
  • Page 181 When installing Wireless LAN Cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required.
  • Page 182 Portégé M200 V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 183 Result codes for a V.90 connection Result code CONNECT 32000 EC* CONNECT 36000 EC* CONNECT 40000 EC* CONNECT 44000 EC* CONNECT 48000 EC* CONNECT 52000 EC* CONNECT 56000 EC* CONNECT 28000 EC* CONNECT 29333 EC* CONNECT 30666 EC* CONNECT 33333 EC* CONNECT 34666 EC* CONNECT 37333 EC* CONNECT 38666 EC*...
  • Page 184 EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis NoEC AT Command V90=* V90=0 V90=1 Portégé...

  • Page 185: Glossary

    Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference. AccuPoint II: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices.
  • Page 186 asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. AUTOEXEC.BAT: A batch file that executes a series of MS DOS commands and programs each time you start the computer.
  • Page 187 cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
  • Page 188 compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 189 data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve.
  • Page 190 echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT.
  • Page 191 The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. Portégé M200...
  • Page 192 I/O devices: Equipment used to communicate with the computer and transfer data to and from it. I/O: Input/output. Refers to acceptance and transfer of data to and from a computer. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 193 level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewing side coating is etched into character forming segments with leads that extend to the edge of the glass.
  • Page 194 motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board. MPEG: Moving picture coding expert group is an industry standard architecture for compression of video signals.
  • Page 195 parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parallel: Refers to two or more processes or events that can occur simultaneously, and without interfering with each other. See also serial.
  • Page 196 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. RAMDRIVE: Part of the computer’s random access memory assigned to simulate a disk.
  • Page 197 SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. serial communications: A communications technique that uses as few as two interconnecting wires to send bits one after another. serial interface: Refers to a type of information exchange that transmits information sequentially, one bit at a time.
  • Page 198 USB: The Universal Serial Bus is a way to connect up to 127 devices through one connector. A new development in 1997, this offers significantly improved ease of use and reliability than earlier expansion methods. VGA: Video graphics array is an industry standard video adaptor that lets you run any popular software.

  • Page 199: Index

    Portégé M200 Index AC adaptor, 1 5, 2 13 connecting, 3 6 AC Adaptor, 8 10 ASCII characters, 5 9, F 1 battery indicator, 6 2 types, 6 3 Battery, 2 11 Charger, 8 10 charging, 6 7 charging notice, 6 8 charging time, 6 8 extending life, 6 10 lock, 2 6...
  • Page 200 FDD, 4 14 Fn+Ctrl (enhanced keyboard simulation), 5 4 Fn+Enter, 5 4 Fn+F10 (arrow mode), 5 3, 5 7 Fn+F11 (numeric mode), 5 3, 5 8 Fn+F12 (ScrLock), 5 3 Hard disk drive, 1 4 Headphone, 2 1 Heat dispersal, 4 29 Hibernation, 1 9 benefits, 3 11 starting, 3 11...
  • Page 201 9 2 Real Time Clock, 9 17 SD card, 9 12 Sound system, 9 13 Standby/Hibernation, 9 14 support from TOSHIBA, 9 17 system start up, 9 4 USB, 9 13 Wireless LAN, 9 16 Processor, 1 3...
  • Page 202 Reserve Pen, 4 2, 8 12 inserting, 4 7 removing, 4 7 set, 8 12 slot, 2 3 TOSHIBA Password Utility, 6 14 TOSHIBA Tablet mode, 6 16 Toshiba Utilities, 1 7 Touch pad, 1 4, 2 8 control buttons, 2 8...

Table of Contents