Machine Controls And Parts; Description Of The Control Panel; Unpacking/Installation; Power Supply Connection - Saeco 0340.0BR.47Q User's And Maintenance Booklet

79
IMPORTANT SAFEGUARDS
a) A short power-supply cord (or detachable power-supply cord) is to be provided to reduce
risks resulting from becoming entangled in or tripping over a longer cord.
b) Longer detachable power-supply cords or extension cords are available and may be used
if care is exercised in their use.
c) If a long detachable power-supply cord or extension cords is used,
1) The marked electrical rating of the detachable power-supply cord or extension cord
should be at least as great as the electrical rating of the appliance,
2) If the appliance is of the grounded type, the extension cord should be a grounding-
type 3-wire cord, and
3) The longer cord should be arranged so that it will not drape over the counter top or
table top where it can be pulled on by children or tripped over.
1 Coffee grounds container
2 Drip tray
3 Cup holder surface
4 Main switch
5 Power cord
6 Coffee dispensing unit
7 Steam/hot water spout wit burn-protection
8 Control panel
9 Steam knob
10 Cup heating plate
11 Water tank
12 Water tank cover
13 Water level
14 Pre-ground coffee container with cover
15 Coffee bean container cover

Description of the control panel

Digital display
Standby switch:
energy saving function on/off
Selection key for 1 or 2 cups of tall coffee or key
" " in the programming mode
Selection key for 1 or 2 cups of regular coffee
or key " " in the programming mode
Selection key for 1 or 2 cups of espresso coffee
or "ESC" in the programming mode
Pre-ground coffee selection button or "ENT" in
the programming mode
Cappuccino selection key
Hot water on/off key

MACHINE CONTROLS AND PARTS

16 Coffee bean container
17 Grind adjustment lever
18 Coffee dosage adjustment lever
19 Service door
20 Filling funnel
21 Handle for assembling and disassembling
of central unit
22 Central unit
23 Coffee rest drawer
24 Swivel
25 Cappuccinatore
26 Suction pipe
27 Dispenser
28 Cappuccinatore adjusting valve
29 Cappuccinatore cover
WARMING UP......
ESC ENT
80

Unpacking/installation

Standard packing is strong enough to protect the
machine during mail shipping. Keep this package
to return the machine to the manufacturer,
whenever necessary.
Before installing the machine, keep to the safety
indications at page 77.
Whenever possible, use the machine with swivel
(24). When installing the machine, make sure
the swivel is always fitted in the provided area on
the lower side of the machine.

Power supply connection

Warning: electric current may cause d e a t h !
Always keep to safety rules.
The coffee machine must be connected to an
adequate socket. Voltage must suit to the voltage
specified on the appliance rating plate.
Never use defective power cords! Defective
power cords and plugs must be replaced by an
authorised personnel.
Should an extension cord be used, check its
perfect conditions. The extension cord must have
a minimum section of 1,5 mm 2 or 16 AWG and
must be supplied with a three-pole plug/socket.

Starting and use

Parts under current shall never be in
contact with water: danger of short-
INSTALLATION
circuit! Overheated steam and hot
water may cause burns. Do not direct
steam or water jet towards the body;
furthermore, great attention must be
given when touching either the steam/
hot water spout or the heating plate:
danger of burns!
Never use the machine without water or coffee
beans.
Remove measuring spoon, brush and the central
unit key from the coffee grounds container (1)
and keep them within reach.
Unwind the power cord (5) from the rear side
of the machine.
30
Remove the cover (15) and fill the container with
coffee beans (300 g approx.), then, replace the
cover. Adjust grinding by means of the grind
adjustment lever (17), positioning it on point "5"
of the scale.
Never fill the coffee bean container with other
products since they might damage the machine!
Before filling the container with coffee beans,
make sure the pre-ground coffee container (14)
is closed to prevent coffee beans from falling into
it. They might damage the machine!
Remove water tank (11) from the machine,
remove its cover (12) and fill it with cold water
(approx. 2.4l). A valve on the tank bottom
prevents water from escaping.
Before installing the water tank in the
machine, make sure the coffee bean
container cover is properly fitted.