Page 1
FWM593 MP3-CD Mini Hi-Fi System Register your product and get support at www.philips.com/welcome...
Page 2
LEA CUIDADOSAMENTE ESTE INSTRUCTIVO ANTES DE USAR SU APARATO. AVISO IMPORTANTE Philips Mexicana, S.A. de C.V. no se hace responsable por daños o desperfectos causados por: – Maltrato, descuido o mal uso, presencia de insectos o roedores (cucarachas, ratones etc.).
Page 4
CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. ATENCIÓN El uso de mando o ajustes o la ejecucción de métodos que no sean los aquí descritos puede ocasionar peligro de exposición a radiación.
Page 5
Index English ------------------------------------------------ 6 Español --------------------------------------------- 24 Português ------------------------------------------ 52...
Contents General Information Supplied accessories ... 7 Environmental information ... 7 Safety information ... 7 Preparations Rear connections ... 8~9 Power Antenna connection Speakers connection Optional connection ... 9~10 Connecting a USB device or memory card Connecting other equipment to your system Inserting batteries into the remote control ...
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/ welcome. IMPORTANT! PLEASE NOTE THAT THE VOLTAGE SELECTOR LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 220V FROM THE FACTORY.
Preparations FM antenna Speaker (right) AC power cord Rear connections The type plate is located at the rear of the system. Power Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. If your system is equipped with a Voltage Selector, set the VOLTAGE SELECTOR to the local power line voltage.
FM Antenna ● For better FM stereo reception, connect an outdoor FM antenna to the FM ANTENNA terminal. Speakers Connection Front Speakers ● Connect the speaker wires to the SPEAKERS terminals, right speaker to "R" and left speaker to "L", white wires to "+" and black wires to "-" of the woofer connection terminals, blue wires to "+"...
Preparations Inserting batteries into the remote control Insert two batteries (Type R03 or AAA, supplied) into the remote control with the correct polarity as indicated by the "+" and "-" symbols inside the battery compartment. CAUTION! – Remove batteries if they are exhausted or will not be used for a long time.
Controls on the system Disc tray Display screen – to view the current status of the system. Mode Selection ALBUM/PRESET -/+ for MP3-CD ... to select previous/next album. for Tuner ... to select a preset radio station for Clock/Timer ... to set the hour. for Clock ...
Controls Controls on remote control – to switch the system on or to standby mode. Source selection – to select the following: CD 1/2/3 – to select disc tray 1, 2 or 3. TUNER – to select waveband: FM or AM. –...
IMPORTANT! Before you operate the system, complete the preparation procedures. Plug and Play (for tuner installlation) Plug and Play allows you to store all available radio stations automatically. First time setup/power up When you turn on the main supply, "AUTO INSTALL - PRESS PLAY"...
Basic Functions Switching the system to standby mode In any other source mode ● Press 2. ➜ The clock will appear on the display when the system is in standby mode. Power-saving automatic standby As a power-saving feature, the system will automatically switch to Standby mode if you do not press any buttons within 15 minutes after a disc/USB has stopped playing.
Light mode demonstration ● Press once or repeatedly LIGHT on the set to demonstrate different lighting styles. ● First press -> It flashes alternatively between the three LEDs (STANDBY, DBB and USB) and another three LEDs (VOLUME, USB Ripping and MAX).
CD/MP3-CD/WMA Operations IMPORTANT! – This system is designed for regular discs. Therefore, do not use any accessories such as disc stabiliser rings or disc treatment sheets, etc., as offered on the market, because they may jam the changer mechanism. – Do not load more than one disc into each tray.
Press OPEN•CLOSE to close the disc tray. ➜ READING is displayed as the CD player scans the contents of a disc, and then the total number of tracks and playing time (or the total number of albums and tracks for MP3/WMA disc) are shown.
CD/MP3-CD/WMA Operations Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. The REPEAT modes can also be combined with PROGRAM..plays the current track continuously ALL ... repeats the entire disc/ programme ...
Tuning to radio stations Press TUNER. ➜ "FM" or “AM” is displayed. A few seconds later, the current radio frequency will appear on the display. Press TUNER again to select the desired waveband : FM or AM. Hold S / T (or ALBUM +/- (à / á) on the remote control) and then release the button.
Radio Reception Manual programming Tune to your desired radio station (refer to “Tuning to radio stations”). Press PROG/CLOCK (or PROGRAM on the remote control). ➜ starts flashing. PROG ➜ The next available preset number is displayed for selection. To store the radio station to another preset number ●...
Using a USB mass storage device By connecting a USB mass storage device or SD/ MMC memory card to the Hi-Fi system, you can enjoy the device's or card’s stored music through the powerful speakers of Hi-Fi system. Playing a USB mass storage device Compatible mass storage devices/cards With the Hi-Fi system, you can use: –...
How to transfer music files from PC to a USB mass storage device By dragging and dropping music files, you can easily transfer your favorite music from PC to a USB mass storage device/SD/MMC memory card. For a flash player, you can also use its music management software for the music transfer.
Ripping function This function enables you to record music to a connected USB mass storage device from any other source (i.e., DISC, TUNER or AUX) without interrupting your enjoyment of the music. Insert a USB mass device with sufficient free space to the USB DIRECT the set.
Tuner record timer setting This function enables you to set a timer for starting and stopping ripping from the tuner source automatically. IMPORTANT! – Before setting the timer, ensure that the clock is set correctly. Tune to the station you desire to record from. (See "Radio Reception": "Tuning to radio stations"...
Listening to external sources Using AUX IN (white/red jacks) Use the audio cables (white/red, not supplied) to connect AUX IN (L/R) jacks of the main unit (located on the back panel ) to the corresponding AUDIO OUT jacks on an external device (such as TV or VCR).
Clock/Timer Clock setting The clock can be set in either 12-hour or 24-hour mode ("AM 12:00" or "00:00" for example). In standby or view clock mode, press PROG/ CLOCK (or CLOCK on the remote control). Press ALBUM/PRESET -/+ (or ALBUM -/+ (à...
Press S / T (or TITLE +/- (í / ë) on the remote control ) repeatedly to set the minute for the timer to start. Press SLEEP/TIMER on the remote control to store the start time. ● At the preset time, the selected source will play. To exit without storing the setting ●...
Cleaning the disc lens ● After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner.
AMPLIFIER RMS output power 1KHz (Low channel-both channels driven) ..100 W per channel 10KHz (High channel-both channels driven) ..100 W per channel Total output power ... 580 W Signal-to-noise ratio ... 67 dB A (IEC) Frequency response ... 60 – 16000 Hz Input sensitivity AUX ...
Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help.
Page 31
The remote control does not function properly. The time is not working. The Clock/Timer setting is erased. Some files on the USB device are not displayed. “DEVICE NOT SUPPORTED” scrolls on the display. Troubleshooting ✔ Select the source (DISC or TUNER, for example) before pressing the function button (É...