Table of Contents
Advertisement
6-32 x 5/8 Long Phillips Head Screws
W9407400BE
Figure 1: Remove Phillips Head Screws
2.
Remove the end cap from the housing by pulling out the
cradle assembly. See Figure 2.
W9407401AE
Figure 2: Remove Cradle Assembly
3.
Place the camera/lens on the cradle assembly. The
correct positioning for mounting either a camera with a
fixed lens or a camera with a zoom lens is shown in
Figure 3.
W9407402AE
Figure 3: Camera/Lens Mounting Positions
4.
Fixed Lens Cameras: Secure the camera/lens to the
cradle with the 1/4-20 x 1/2-inch screw, nylon bushing,
5/16-inch flat washer, and 2.5 mm (0.100 inch) plastic
washer. Make sure the thermoplastic shield is under the
camera in the correct position. Be sure that the nylon
bushing is in place. All hardware shown below must be
used. For LTC 0240 Series cameras, use 1/4-20 x 7/8
inch BHCS, nylon bushing, 5/16-inch flat washer, and 9.8
mm (0.385 inch) plastic spacer. See Figure 4.
Plastic Washer
5/16 Inch Flat Washer
Nylon Bushing
1/4-20 x 1/2 Screw
Mounting Position For
Camera With Fixed Lens.
W9407403AE
Use 1/4-20 x 1/2 Screw
Figure 4: Camera/Fixed Lens Mounting Position
Zoom Lens Cameras: Use same procedure as fixed
lens cameras. All hardware shown below must be
used. See Figure 4a.
Mounting Position For
Cameras With TC9948 6X
Zoom Lens. Use 1/4-20 x 1/2-Inch
Screw Provided. Be Sure Plastic
Washer Is In Place.
Mounting Position For
TC9948 6X Zoom Lens.
Use 1/4-20 Screw Provided.
W9407404AE
Figure 4a: Camera/Zoom Lens Mounting Positions
LTC 9353/00 and LTC 9358/00 Only
Note: Refer to section 5a for LTC 9352/01 model power
wiring instructions.
5.
When installing 120 or 220 volt cameras, the camera
power cord must be cut leaving enough cable to strip
and attach to the terminal block. Strip no less than 6
mm (1/4 in) and no more than 8 mm (5/16 in) of
insulation away from the wires, making sure not to nick
the wires. Attach the wires to the terminal block. See
Figure 5 and Figure 6.
Insert the loose end of the power supply cable or the
remainder of the camera power cord through the lower
right fitting. The fitting accepts cables with diameters
from 1.8 mm (0.07 in) to 6.6 mm (0.26 in). Tie a figure-
eight knot in the wire to prevent strain on internal
circuits. Repeat the same procedure for stripping the
wires. Attach the wires to the opposite side of the
terminal block. Crimp the ground wire to the ground
lug located on the reverse side of the cradle. See
Figure 5 and Figure 6.
Rear Cap
CCD Camera
250
2000
Min.
Max.
250 Min.
W9407405AE
Cradle
Figure 5: Cut Camera Power Cord
Note: If power is supplied from a pan/tilt feed thru,
follow the same instructions as above for wiring
procedures. Figure 6 shows the relationship with
color codes.
Hint: For ease of wiring, remove the terminal block
from its mounted position. Wire accordingly and
remember to maintain polarity. Remount the terminal
block with the wires in place. See Figure 6.
Page 4
Advertisement
Table of Contents
