Honeywell AlarmNet IGSMHS Installation And Setup Manual page 37

Internet communication module
Hide thumbs

Advertisement

Table of Contents
PROMPTS
Restore Zn7 Y/N
63
(Y)_
Delay Zn7 (secs)
64
(00)_
Rpt Zn7 ONLY if
65
Armed (N)_
66
Restore Zn8 Y/N
(Y)_
Delay Zn8 (secs)
67
(00)_
NOTE: Prompts 68 through 73 only appear if the Comm Path Choice is IP, or IP&GSM.
68
Use DHCP Y/N
(Y)_
NIC IP Address:
69
255.255.255.255_
70
Subnet Mask:
255.255.255.255_
Gateway IP Addr:
71
255.255.255.255_
72
DNS Serv IP
Addr:
255.255.255.255_
Enable Pwr Save
73
(Y)_
4204/
ZONE
ENTRY
TRIG.
2-4204
2-
4204
only
2-
4204
only
Section 3: Programming the IGSMHS
OPTIONS
[Y], [N]
Enables restore reporting for zone 7.
Zone Trigger mode: This prompt will only be
displayed if zone 7 is not used as the conditional
(arming) trigger zone.
UL: Must be set to "Y."
[01-15]
Defines the reporting delay in seconds for
zone 7.
[00] = no
Zone Trigger mode: This prompt will only be
delay
displayed if zone 7 is not used as the conditional
(arming) trigger zone.
UL: Must be set to 00.
[Y], [N]
Reports alarms on zone 7 ONLY if the
conditional zone (zone 4 in 4204 mode; zone 8 in
2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 7.
2-4204 mode: If any zone is programmed to
"Report Only if Armed," or if tamper is enabled,
skip to Prompt 68: "Use DHCP."
[Y], [N]
Enables restore reporting for zone 8.
UL: Must be set to "Y."
[01-15]
Defines the reporting delay in seconds for
zone 8.
[00] = no
delay
UL: Must be set to 00.
[Y], [N]
Dynamically allocates the IP addresses (recom-
mended); then skip to Prompt 73: "Enable Pwr
Save". If [N], uses fixed IP addresses.
12 digit:
Enter the 4-part address for this device. The 4
xxx.xxx.xxx.
parts of the address must be separated by
xxx
spaces (displayed as periods in Review mode).
12 digit:
Enter the 32-bit address mask used to indicate
xxx.xxx.xxx.
the portion (bits) of the IP address that is being
xxx
used for the subnet address. The 4 parts of the
address must be separated by spaces (displayed
as periods in Review mode).
12 digit:
Enter the 4-part address assigned to the
xxx.xxx.xxx.
Gateway. The 4 parts of the address must be
xxx
separated by spaces (displayed as periods in
Review mode).
12 digit:
Enter the 4-part IP address assigned to the
xxx.xxx.xxx.
DNS (Domain Name System) server. The 4
xxx
parts of the address must be separated by
spaces (displayed as periods in Review mode).
[Y], [N]
To meet the 24 hour UL battery backup
requirement, choose "Y" to enable this feature.
If this causes connectivity problems with
certain routers or switches, then choose "N" and
wire the communications module so it is
plugged into a UL listed UPS.
UL: Must be set to Y.
DESCRIPTION
3-19

Advertisement

Table of Contents
loading

  Related Manuals for Honeywell AlarmNet IGSMHS