4204 Emulation Mode; 4204 Emulation Mode Options - Honeywell AlarmNet IGSMHS Installation And Setup Manual

Internet communication module
Hide thumbs

Advertisement

Table of Contents
IGSMHS Installation and Setup Guide
When using Zone Trigger mode, messages are sent in ADEMCO High-Speed format.
Zones 3, 4, 5, 6 and 7 are voltage trigger inputs located on TB1 pins 6-10. If the Lynx Panic
feature is being used, do not connect zone 3 (the second physical zone input).
Refer to Table 3-4 for Zone Trigger Mode programming and follow the prompts that pertain
to Zone Trigger Mode. A check mark (

4204 Emulation Mode

In 4204 Emulation Mode, the IGSMHS communicates with a compatible Honeywell VISTA
series or First Alert control panel as though it were a 4204 Relay Module. If two 4204s are
enabled in the module, it acts as two 4204s at consecutive device addresses. The control
panel must be configured to recognize one or two 4204 relay modules accordingly. On
VISTA-32FB (or higher) control panels and First Alert equivalents, addresses 6 and 13
should not be used when the secondary 4204 is enabled. Messages are sent in ADEMCO
High-Speed format.
NOTE: See your control panel Installation and Setup Guide for the number of 4204 modules

4204 Emulation Mode Options

For control panels that do not support ECP communication, the 4204 Emulation modes
provide a means of sending up to eight unique reports based on defined system conditions.
In 4204 mode, the IGSMHS functions as a logical 4204 Relay Module, where each relay
number, referred to in the module as zone number, can be programmed to send a report
based on the output function programmed in the control panel for that relay. Each relay-
zone can also be programmed to send a restore message of the reported condition, can be set
to delay transmission of messages, and can be programmed to send reports only when a
conditional zone is triggered (armed), (see Important Information Regarding Zone Input
Options later in this section).
In single 4204 mode, the IGSMHS supports up to four relay-zones. In Two-4204 mode, the
IGSMHS functions as two 4204 modules, supporting up to eight relay-zones.
U L
4204 Relay Outputs map to IGSMHS zones as follows:
First 4204 Zones
(device address entered in Prompt 14):
Relay 1 = Zone 1
Relay 2 = Zone 2
Relay 3 = Zone 3
Relay 4 = Zone 4 or conditional zone trigger if
"report only if armed" is selected in any zone 1-3
when using single 4204 mode.
NOTE: Zone 4 status is not reported when being
used as the conditional (armed) trigger zone.
When using the IGSMHS in 4204 Emulation Mode, DO NOT enable the Long-Range Radio
module in control panel programming. Instead, enable 4204 relay module address(es) and
program the appropriate relay activation functions for the relay-zones being used. In some
control panels, it is called "relay programming" and in others it is called "output device
programming." It is recommended that "close and stay closed" (usually choice 2) action is
selected. Selection of momentary activation will cause the IGSMHS to generate an alarm and
NOT a restore, even if the IGSMHS is programmed to send a restore for the given zone.
In 4204 mode, messages are reported in ADEMCO High-Speed format. Zone alarms
(status 7) are reported with "1" (alarm) or "3" (restore) displayed in the zone position for the
respective zone (e.g. alarm on zone 2: 5155 5555 7; restore 5355 5555 7). A supervision fault
3-10
supported.
4204 Mode and Two-4204 Mode has not been evaluated.
) indicates whether the prompt applies to that mode.
Second 4204 Zones
(device address entered in Prompt 14, plus 1):
Relay 1 = Zone 5
Relay 2 = Zone 6
Relay 3 = Zone 7
Relay 4 = Zone 8 or conditional zone trigger if
"report only if armed" is selected in any zone 1-7
when using Two-4204 mode.
NOTE: Zone 8 status is not reported when being
used as the conditional (armed) trigger zone or if
tamper reporting is enabled.

Advertisement

Table of Contents
loading

  Related Manuals for Honeywell AlarmNet IGSMHS