Angelo Decor Pond Building Series Instruction Manual

REPLACING THE BULB

1. Unplug the light and allow it to cool.
2. Turn the locking ring counter clockwise to remove the lamp holder (02).
3. Carefully remove the old bulb by firmly pulling on the base. Carefully install the new bulb.
4. Reinstall the lamp holder and locking ring. Plug the light into a properly grounded electrical outlet.

CARE AND MAINTENANCE

To maximize performance, periodically disassemble the unit to clean the glass tube.
IMPORTANT:
Be sure that the entire unit is completely dry and gaskets are properly seated when
reassembling. Failure to do so will result in water leakage, which can cause damage.
1. Disconnect the UV light from the outlet. Be sure to allow sufficient time for the light to cool
before disassembling the light.
2. Unscrew the locking ring, and pull out the light unit.
3. Carefully pull out the glass tube holder by twisting and then pull out.
4. Use biodegradable soap and warm water to clean the glass tube.
5. Reassemble and be sure that all gaskets and o-rings are seated properly.

TROUBLESHOOTING:

If the light fails to operate:
 Check to ensure the power cord is plugged in and the light is getting power. 

Check to ensure that the lamp holder is screwed completely into the body. (This product will not
operate unless it is fully assembled with the lamp holder screwed completely into the body.) 
 Check bulb to ensure that it has not burned out. Replace the bulb as necessary. 

LIMITED WARRANTY

This product is warranted to the original user against defective materials and workmanship for a
period of 12 months. Our limited warranty does not cover any costs associated with the installation
or removal of products subject to warranty claims or the cost of return of the product. The warranty
will commence from the date of purchase. Replacement liability is limited to any part or parts of the
unit which have failed due to defective material or workmanship. Proof of purchase is required for
all claims against the limited warranty. This warranty does not extend to damage of the product or
part resulting from accident, misuse, alteration, neglect, abuse, improper installation or normal wear
and tear to the product(s). This limited warranty extends only to the original user of the product.
For more information on this and other products, please visit our web site:
www.angelodecor.com
To contact us regarding this unit, your options include:
Email:customersupport@angelodecor.com | Phone: (780) 453 - 6646 | Fax: (780) 453- 6620
Angelo Décor International Inc. | 15840 – 118
th
Avenue | Edmonton, AB |T5V 1C4
9 WATT UV CLARIFIER

COMPONENTS

01. UV Bulb
02. Lamp Holder
03. Lamp Housing
04. Adapter
05. Adapter nut
06. Adapter Gasket
07. O-ring 1
08. O-ring 2
09. Lamp Holder Gasket
10. Bulb Cover

BEFORE YOU BEGIN

Before you get started check the packaging to ensure you have all parts and compare against
packaging and illustration above. Do not assemble or attempt to operate the unit if any parts are
missing. Contact customer support regarding any missing parts or components.


IMPORTANT INFORMATION


This product will not operate unless it is fully assembled with the lamp base screwed completely
into the housing. 

UV rays are harmful to your eyes and skin. The indicator portal will remove the harmful effects of
the UV light but still allow you to see the bulb operating. 

Do not attempt to operate this product unless the lamp is completely assembled within
the light housing. 
 This product is to be operated within the following temperature range: 32°F - 95°F (0°C - 35°C). 

This product conforms to the Code of Federal Regulations (CFR) requirements including,
Title 21, Chapter 1, Subchapter J, Radiological Health.
Questions, problems or missing parts?
Email our Customer Support team at: customersupport@angelodecor.com
AD46530
05
04
06
03
10
08
07
01
09
02
