Philips HB554/02 User Manual page 7

During this minute, you can set the timer again to tan the other side of your body.
- If you do not set the timer again in the last minute, the appliance switches off automatically when the set time has elapsed.
Face tanner (HB556 only)
Make sure you position the appliance in such a way that the face tanner points towards your face.
You can switch the face tanner on or off with the on/off switch.
If you have switched off the face tanner and want to use it again, the lamp has to cool down for 3 minutes before it can be switched on again.
tanning with the canopy in horizontal position
1 Place the tanning appliance beside a bed or couch.
 Lie down on the bed or couch and pull the appliance towards you (Fig. 16).
3 Make sure that the lamps are positioned straight above your body.
4 After use, you can push the tanning appliance away from you so that you can get up more easily.
tanning with the canopy in tilted position
1 Place a chair in front of the tanning appliance (Fig. 17).
 Tilt the canopy to the optimal position by pulling one of its ends downwards.
tanning with the canopy in vertical position
1 Tilt the canopy until it is in vertical position.
If necessary, adjust the height of the stand.
 Stand in front of the tanning appliance, at least 0cm away from it (Fig. 18).
Cleaning
Always unplug the appliance and let it cool down before you clean it.
Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance.
Never use liquids such as alcohol, methylated spirits, petrol or acetone to clean the acrylic sheet as this may cause irreparable damage.
1 Clean the outside of the appliance with a damp cloth.
Do not let water run into the appliance.
 Clean the protective goggles with a moist cloth.
storage
- The tanning appliance takes up little space when you store it in vertical position (Fig. 19).
Replacement
lamps and starters
The light emitted by the tanning lamps becomes less bright in time (i.e. after a few years in case of normal use). When this happens, you notice a
decrease in the tanning capacity of the appliance. You can solve this problem by setting a slightly longer tanning time or by having the tanning
lamps replaced.
Always have the tanning lamps and starters replaced by a service centre authorised by Philips. Only they have the knowledge and skills
required for this job and the original spare parts for the appliance.
- If you really insist on replacing the tube lamps and/or starters yourself, proceed as follows:
1 Remove the mains plug from the wall socket.
 Undo the screws and remove the two end covers of the canopy (Fig. 0).
3 Remove the acrylic sheet (Fig. 1).
You can now remove the tube lamps and the starters.
If you wish, you can now also clean the inside of the acrylic sheet. See chapter 'Cleaning'.
4 Turn the lamps slightly to the left or right until they unlock.
5 Pull the lamps out of their holders.
6 Remove the starters by turning them slightly to the left and pulling them out.
7 Insert new lamps and/or starters by following the instructions above in reverse order and direction.
8 Slide the acrylic sheet back into the canopy.
9 Put the end covers back onto the canopy and fix them with the screws.
Face tanner (HB556 only)
- Always have the UV filter of the face tanner replaced right away when it is damaged or broken. Never use the face tanner when the UV
filter is damaged, broken or missing.
Always have the tanning lamp of the face tanner replaced by a service centre authorised by Philips. Only they have the knowledge and skills
required for this job and the original spare parts for the face tanner.
Protective goggles
Additional or replacement goggles, type HB071, can be ordered under service number 4822 690 80123.
EnglisH
7