Table of Contents
Advertisement
Available languages
Available languages
Now Start...
With dryer in laundry area.
Excessive Weight Hazard
Usetwo or more people to move and
installdryer.
Failureto do so can resultin back or
otherinjury.
3-prong,
ground-type
outlet
gas supply line
gas shuloff valve
l
mTake tape
off front corners of
dryer, Open dryer and remove
the
literature
and parts packages,
Wipe
the interior of the drum thoroughly
with a damp
cloth,
mTake two of the cardboard
corners from the carton
and place
them on the floor in back of the dryer,
Firmly grasp the body of the dryer
and gently lay it on its back on the
cardboard
corners,
mWith one of the legs in hand,
check
the ridges for a diamond
marking, That's how far the leg is
supposed
to go into the hole,
mStaff to screw the leveling
legs
into the holes by hand, (Use a small
amount
of liquid detergent
to
lubricate
the screw threads
so it is
easier to turn the legs,) Use a 1-inch
wrench
or socket wrench
to finish
turning
the legs until you reach the
diamond
mark,
Now stand the dryer up,
Slide dryer onto cardboard
or
hardboard
before moving across floor
to avoid damaging
floor covering.
m Move dryer close to final
position, Remove
cardboard
or
hardboard
from under dryer,
a Remove
red cap from gas pipe,
Carefully
move dryer into final
position, Place level on top of the
dryer, first side to side; then front to
back, If the dryer is not level, adjust
the legs of the dryer up or down until
the dryer is level,
a Connect
gas supply to dryer,
Use pipe-joint
compound
resistant to
the action
of L,P, gas for gas
connections,
If flexible
metal tubing
is
used, be certain
there are no kinks,
If necessary
for service, open the toe
panel, use a putty knife to press on
the toe panel
lock located
at the
center
top of the toe panel, Pull
downward
on the toe panel
to open,
Toe panel
is hinged
at the bottom,
m Open the shutoff valve in the
gas supply line,
mUse a non-corrosive leak
detection
fluid to check for leaks,
Bubbles around connections will
indicate a leak, If a leak appears,
shut off gas valve controls and adjust
connections, Then check
connections again, Close toe panel,
All connections must be wrench-
tightened.
0
• To exhaust dryer, see Exhaust
requirements,
Pages 3-4, Connect
exhaust vent system to dryer exhaust
outlet
and exhaust
hood using 4"
(10,2 cm) clamps,
Use caulking
to
seal exterior wall opening
around
exhaust
hood,
1
• Carefully
move dryer into
final position,
Place level on top of
the dryer, first side to side; then front
to back,
If the dryer is not level, adjust
the legs of the dryer up or down
until
the dryer is level,
1 2
• Plug power supply cord
into
grounded
outlet,
I
3
• Check
dryer operation
(some
accumulated
time may be on the
timer due to factory
testing),
Pull timer-set
button
left, (Operating
time will accumulate
per number
of
depressions
and type of timing cam
used,) Push START/RESTARTbutton,
Using a full heat cycle (not the air
cycle),
let the dryer run for at least
five minutes,
Note: Dryer door must be closed for
dryer to operate,
When door is open,
dryer stops, but timer continues
to run,
To restart dryer, close door and push
START/RESTARTbutton,
4.
If the burner does not ignite
and you can feel no heat inside the
dryer, shut off dryer for five minutes,
Check
that all supply valve controls
are in "ON" position
and that the
electrical
cord is plugged
in, Repeat
five-minute
test,
5
• If drying time is too long,
make sure lint screen is clean,
Page 6
Advertisement
Table of Contents
