Subscribe to Our Youtube Channel
Related Manuals for Mamas & Papas Bubble bouncing cradle
Summary of Contents for Mamas & Papas Bubble bouncing cradle
- Page 1 ABUB01: V1/06/07 © Mamas & Papas (Holdings) Ltd. 2007 WARNING - IMPoRtANt keeP foR fUtURe RefeReNce. Bubble Cradle V1.indd 1 8/6/07 14:24:50...
- Page 2 BuBBle Bouncing cradle These insTrucTions are imporTanT. please read carefully and reTain for fuTure reference. The correct use and maintenance of your cradle will ensure it gives a long and trouble free use. When somebody else is using your cradle, ensure they also know how to use and adjust it and all necessary safety precautions. The safety of your child is your responsibility. after sales service: If you need assistance, spare parts or you are unhappy with any aspect of the goods please contact customer services on: +44 (0)845 268 2000, or e-mail us at: customer.services@mamasandpapas.com. Visit our website at www.mamasandpapas.com...
- Page 3 assemBling the frame a: Slot the ends of the legs into the holes in the ends of the leg connector. B: Slot the backrest frame through the mouldings on the seat frame as shown in the diagram. Fasten the mouldings to the backrest frame using the two frame screws. c: Slot the ends of the backrest frame onto the top of the legs. d: Slot the vibration unit into the slot in seat section of the front of the backrest frame. - 3 - Bubble Cradle V1.indd 3 8/6/07 14:24:52...
- Page 4 fitting the cover a: Slip the back of the cover over the backrest frame. B: Slot the front of the cover over the seat section of the backrest frame. c: Slot the elasticated hole in the front of the cover around the top of the vibration unit. d: Push the seat section of the backrest frame down until it locks over the lugs on the pivots. To remove the cover, reverse the procedure for fitting it. - 4 - Bubble Cradle V1.indd 4 8/6/07 14:24:52...
- Page 5 fitting the toy arch and toys a: Slot the two plastic clips on the ends of the toy arch over the seat frame above the pivot. B: Attach the toys to the toy arch by looping the straps on the toys over the toy arch. Fasten the velcro tabs on both ends of the straps together. - 5 - Bubble Cradle V1.indd 5 8/6/07 14:24:54...
- Page 6 using the viBration unit inserting/changing the batteries. Place the vibration unit upside down and remove the screw holding the battery cover in place using a small cross- head screwdriver. Insert two type “aa” batteries as shown in the battery compartment. Ensure the batteries are correctly inserted. Incorrectly fitted batteries may damage the unit. Refit the battery cover. operating the vibration unit. Turn the dial clockwise to start the unit. The further clockwise the dial is turned the stronger the sensation. Turn the dial anti-clockwise to turn the vibration down and off. note: It may be necessary to increase the strength of the vibration as your child grows or with fluctuations in the...
- Page 7 using the safety harness Warning: Never place your child in the seat without fitting and adjusting the safety harness. a: locking the harness. Push the locking catch 1 into the buckle 2 until it clicks into place. Repeat for the second lock. B: releasing the harness. Push the two tabs 3 on the locking catch in and detach the buckle. c: adjusting the harness length. To loosen the harness feed the webbing back through the locking catch. To tighten the harness pull the free ends of the webbing outwards - 7 - Bubble Cradle V1.indd 7 8/6/07 14:24:55...
- Page 8 instructions for safe use • WarninG: never leave your child unattended in the rocking cradle. • not recommended for children who can sit up by themselves (6 months approximately: until 9 kgs). • WarninG: it is dangerous to put this rocking cradle on an elevated surface.
Need help?
Do you have a question about the Bubble bouncing cradle and is the answer not in the manual?
Questions and answers