Skil-Care ChairPro E-Z Quick Start Manual

E-Z RELEASE BELT ALARM
Re-Order # Description
Model # Description
909371 E-Z Release Belt with Grommets
909371 ChairPro E-Z Release
Belt Alarm
914119 E-Z Release Belt with Loops
GuaranteeS
1.
The ChairPro E-Z Release Belt Alarm Unit is replace-
1. The E-Z Release belt with Velcro
ment guaranteed for one year following the date of pur-
chase.
replacement guaranteed for one year following the date of purchase.
2.
The E-Z Release belt with Velcro
These guarantees cover defects in materials and workmanship under
netic switch is replacement guaranteed for one year fol-
conditions of normal use. Please return defective part to dealer from whom
lowing the date of purchase.
These guarantees cover defects in materials and work-
it was purchased. The dealer will send the defective part to Skil-Care and
manship under conditions of normal use. Please return
arrange for shipment of a replacement.
defective part to dealer from whom it was purchased. The
dealer will send the defective part to Skil-Care and
arrange for shipment of a replacement.
The ChairPro E-Z Release Belt Alarm is a non-restrictive wheelchair safety
PURPOSE
belt with an integral magnetic alarm switch. It is designed to alert caregivers
The ChairPro E-Z Release Belt Alarm is a non-restrictive
when a patient attempts to leave the wheelchair.
wheelchair safety belt with integral magnetic alarm
switch. It is designed to alert caregivers when a patient
attempts to leave or has fallen from the wheelchair.
1. The ChairPro E-Z Release Belt Alarm is not a substitute for proper
supervision. Fall-risk and wander-risk patients or residents should CAUTIONS
1.
The ChairPro E-Z Release Belt Alarm is not a substi-
be monitored regularly.
tute for proper supervision. Fall-risk residents /patients
2. Check battery each time alarm is used. If weak, replace the "AA" battery.
should be monitored regularly.
3. LED should flash when the magnetic switch is engaged. If LED fails to
2.
Check battery each time alarm is used. If weak,
replace the 9-volt battery.
flash, check battery. Replace if necessary. If LED fails to flash after battery
3.
LED should flash when the magnetic switch is
has been replaced and the plug is properly connected, discontinue use
engaged. If LED fails to flash, check battery. Replace if
of device.
necessary. If LED fails to flash after battery has been
replaced and the plug is determined to be properly con-
nected, discontinue use of device.
Alarm unit made in China. Instructions printed in USA.
Alarm Unit
You may choose one of the following two ways to attach the alarm unit to
the wheelchair.
Attachment of Alarm Unit
1. Remove the second-from-top screw from either the left or
right side of the wheelchair backrest.
2. Remove grommet from screw, place the screw through
hole on alarm unit mounting bracket, and fasten screw to
wheelchair backrest. (Illustration A)
Belt Length
Size Unit
Universal Each
GUARANTEES
closure and magnetic switch is
®
® closure and mag-
PURPOSE
CAUTIONS

INSTALLATION

Mounting Bracket
LED
Mounting Bracket
INSTALLATION
ChairPro Safety Alarm
Test battery before each use. If
weak, replace with 9-volt battery.
LED must glow when alarm is in
use. If not, replace battery.
Auto-Reset
1. Insert enclosed cord
loop through bracket hole.
Unit
(Illustration B)
Battery
Test
30"-44" Set
30"-44" Set
You may choose one of the following two ways to attach
the alarm unit to the wheelchair.
WHEELCHAIR BELT INSTALLATION (Grommet)
Mounting Bracket
1. Remove the rearmost screws
1.
Remove the second-
from the left and right sides of the
from-top screw from either
wheelchair seat. (Illustration D)
the left or right side of the
2. Remove the grommets from
wheelchair backrest.
the screws, place screws
2.
Remove grommet from
through the grommets at
screw, place the screw
the ends of both belt
through hole on alarm unit
mounting bracket,
sections, and refasten the
fasten screw to
screws to the wheelchair seat.
wheelchair backrest.
(Illustration A)
(Illustration E)
3. Select either hole in
belt depending upon desired
Cord Loop
length, closer holes will yield
a shorter length,
holes closet to the end
B
will yield a longer length.
4. Attach the two "spade"
connectors on the connector
wire to those on the seat belt.
1.
Insert enclosed cord
loop through bracket (Illustration F)
hole. (Illustration B)
Note, that for removable arm
wheelchairs it may be easier
Continued on reverse side.
to install the belt after the arm
is removed.
5. Place connector cord through the space between
the wheelchair seat and backrest. Make certain that
it is away from wheels and other moving parts.
WHEELCHAIR BELT INSTALLATION (Loop)
1. UnThread the loop end of the belt.
2. Remove the arm of the wheelchair
(if removable arm)
3. Lay belt on
wheelchair while
holding loop end,
place loop end around
the bottom of the
A
wheelchair (Fig. 1).
4. Place loop and
webbing under both
rectangular rings (Fig. 2)
See Reverse Side
for Loop
installation 5-6.
E-Z Release Belt Alarm
Safety Alarm
Alarm Unit
Cord Loop
Mounting Bracket
LED
MultiPro/ChairPro E-Z Releas.Qk
High
B
Low
Mini-Phone
Plug
Modular
Receptacle
SEAT BELT INSTALLATION
A
Model # Description
and
909393 E-Z Release Velcro
INSTALLATION
1. Remove the rearmost screws
from the left and right sides of
the wheelchair seat. Insert the
screws through the grommets
on the ends of the two belt sec-
tions. Refasten screws to the
wheelchair. (Illustration 1)
2. Place the telephone-style
connector cord through the
space between the wheelchair
seat and backrest. Make certain
that it is away from wheels and
other moving parts.
2.
Hang from wheel-
chair push-handle
(Illustration C)
Alarm system made in China. Instructions printed in USA.
4/3/06 9:38 AM Page 1
C
with E-Z Rel
2. Hang from wheel-
chair push-handle
(Illustration C)
OPE
D
1. Use
replac
fails to
under
should
the tel
Guarantee Unit
If batte
Belt Alarm One Year Each
®
Alarm
to sou
closur
plug c
replac
alarm
sound
of sys
2. Sel
ume.
3. Al
E
when
1
magne
the Au
silence
alarm
mode.
being
C
batter
4. The
magne
5. Afte
patien
ing his
Advanced design for nursing a
F
Fig. 1
Fig. 2
2