Philips CEM220/98 Quick Start Manual

Register your product and get support at
EN Quick Start Guide
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
CEM220
1
a b c
e f g
2
3 4
B
A B
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
a b c d
Overview of parts 1
For cars with ISO connectors
These are the supplied parts needed to
Caution
connect and install this unit.
Be sure to connect the black ground (earth)
1 In-car audio system •
lead fi rst.
2 Sleeve
3 Front panel
4 Standard connector
1
Connect the antenna and amplifi er as
5 Trim plate (2 pieces)
illustrated, if applicable.
6 Rubber cushion
2
Cut off the bigger end of the supplied stan-
7 Disassembly tools
dard connector.
8 Screws 4 pieces
3
Check the car's wiring carefully and connect
them to the supplied standard connector.
4
Connect the supplied standard connector to
Connect wires
the unit.
Caution 1 Green/black
strip
Ensure that all loose leads are insulated with
•
electrical tape. 2 White/black
strip
2 3
For cars with ISO connectors
3 Gray/black
1
Pull out the ISO connectors from car
strip
dashboard and connect them to the bigger
4 Purple/black
end of the supplied standard connector.
strip
2
Connect the other end of the supplied
standard connector to the unit.
3
Connect the antenna and amplifi er as
illustrated, if applicable.
Connector Connect to
1 REAR LINE OUT R Rear right
speaker
2 REAR LINE OUT L Rear left speaker
3 SUB OUT Subwoofer
4 ANTENNA Antenna
5
d
h
a
a a
b
c
d
a
b
b b
c
d
e c
f c
g
h
i
d
d
3 4
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplifi er relay control
lead
g BLACK Ground
h Orange/ Illumination switch
white
i YELLOW To the +12V car battery
which is energized at all
times
Note
Left speaker
• Check wire connection before you mount
(Rear)
the unit into a car.
Left speaker
• If preset radio stations are lost when the
(Front) ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
Right speaker
the yellow ones.
(Front)
Right speaker
(Rear) Attach the front panel 5
1
Attach the trim plate.
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point
the left hole at the left pillar.
4
Release the panel to engage the left side.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
• If you disconnect the car battery in a car that
has an on-board drive or navigation computer,
the computer may lose its memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
• To search for a radio station
Remove the two screws on the top of the
automatically, press SEARCH.
unit.
3
Remove the mounting sleeve with the
Play audio fi les
supplied disassembly tools.
4
1
Ensure that car dashboard opening is
Press on the front panel to release the
within these measurements: panel.
2
5
Install the sleeve into the dashboard and Insert a CD with the printed side facing up.
3
bend the tabs outward to fi x the sleeve.
Close the panel.
6 4
Press 2; , to start play.
Place the rubber cushion over the end of
• To pause CD play, press
the bolt.
• To resume CD play, press
7
Slide the unit into the dashboard until you
hear a click sound.
Insert the USB device
8
Reconnect the negative terminal of the car
battery. 1
Open the cover marked
panel.
2
Turn on Insert the USB device into the USB socket. »
ToThe unit starts playing from the USB
1
device automatically.
Press z to turn on the unit.
• To turn off the unit, press z for 3
seconds.
Insert SD/MMC card
1
Set clock Press to release the panel.
2
Insert the SD or MMC card into the card
1
Press MENU/DISP for 3 seconds.
slot.
2
» The unit starts playing from the SD/
Press 3 or 4 repeatedly to until the cur-
rently time is displayed.
MMC card automatically.
3
Turn z clockwise to set hour.
4
Press z to confi rm.
5
Turn z anti-clockwise to set minute.
6
Press z to confi rm.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Radio.
2
Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3
Press ∞ or § to tune to a radio station
manually.
2; .
2; again.
on the front