Philips CID3291/00 Quick Start Manual

Register your product and get support at
www.philips.com/welcome
ENG Quick Start Guide
4
5
CID3291
1
a
b
c
3
English
Set date and time
1
Press MENU.
Install the car audio 1
»
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
2
Take out the original car audio and keep
the screws.
3
Take off the mounting brackets from the
original car audio and mount them onto
this car audio system.
a
4
2
Connect wires .
2
Tap [Settings].
5
Take off the two screws on the top side of
3
Tap [Time].
the unit. b
6 »
Slide the unit into the dashboard until a
c
click sound is heard.
7
Fix the unit onto the dashboard with
screws. d
8
Reconnect the negative terminal of the car
battery.
Turn on
Set date
Caution
1
Tap [Date].
Risk of road accidents! Never watch video or
2
Tap the displayed date information.
adjust settings while you drive.
» A submenu is displayed.
3
1
Tap
Press to turn on the unit.
»
The available OSD (On-Screen Display)
Set time mode
languages are displayed.
1
Tap [Time Mode] .
2
Tap [12H] or[24H] to select clock mode.
Set time
1
Tap [Time].
2
Tap the displayed time.
»
3
Tap
2
Tap a language to select.
»
The OSD language is changed to the
selected language immediately.
2
Yellow
d
Gearbox
Adjust screen
To turn off the screen
1
The main menu is displayed.
Press DISP for over 2 seconds.
To adjust screen brightness
1
Press DISP.
2
Rotate TUNE/ SELECT to adjust the
value.
Use map
Note
You may need to upgrade the map (sold
The date/time setup menu is displayed. separately) before using it (see "Upgrade the
map" section)
1
Tap the upper left corner to display home
menu.
2
Tap [Navigation].
»
The navigation menu is displayed in a
few seconds.
3
Refer to the map manual to operate the
navigation tool.
Listen to Radio
1
Tap to display home menu.
or to set year, month and day.
2
Tap [Radio].
»
Band and frequency information is
displayed.
A submenu is displayed.
or to set hour and minute.
3
Tap on FM or AM to select band:
4
or to tune to a radio station
by step.
Green Blue
c
AV system
AUX
Play disc Play with Bluetooth device
3
You can play video, audio or images stored on the
following discs:
Pair the Bluetooth-enabled devices
DVD video, DVD-R, DVD-RW
To connect your Bluetooth device to the unit, you
VCD
need to pair the device to the unit. Pairing needs
Audio CD, CD-R, CD-RW
only to be done once.
1
Insert the disc into the disc slot with label
You can pair up to eight devices.
side facing up.
1
Search for Bluetooth device with the device.
»
Play starts automatically.
2
Select "CID3291" in the pairing list.
»
To remove the disc, press the button.
3
Enter default password "0000".
»
if pairing succeeds. phone call record is
displayed.
Connect USB device 4
1
Open the USB door.
2
Insert the USB device to the USB socket.
» Play starts automatically.
Note
To remove the USB device, switch to disc,
Make a call
1
Pair the phone with the unit.
Insert SD/MMC card
5
2
Tap to display the home menu.
3
Tap [Bluetooth].
1
Insert the SD/MMC card into the SD/MMC
»
The Bluetooth menu is displayed.
card slot.
»
Play starts automatically.
Remove the SD/MMC card
1
Switch to another source.
2
Press the card until you hear a click sound.
»
The card is now disengaged.
3
Remove the SD or MMC card.
4
Tap or
tap
5
Tap or
from the following list:
Yellow
Rear display
Yellow
Rear display
Radio antenna
GPS antenna
Optional accessory
Amplifier
Remark:
c Connect the AV IN cable to the AV IN socket on front panel.
Or tap to dial number directly, then tap
to dial.
Receive call
By default, all incoming calls are received
automatically.
1
If there is incoming call, [Incoming call...]
Bluetooth microphone.
2
When conversation ends, tap (red) to
terminate the call.
to select the paired phone, then
.
to search for phone number
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3291_00_QSG_V1.0