Philips CID3688/00 Quick Start Manual

Register your product and get support at Register your product and get support at
CID3688
www.philips.com/welcome www.philips.com/welcome
ENG Quick Start Guide
4
5
1
a
k
a
b
c j
d
e
i
f
g h
b
English
10 Gray and Right speaker (Front)
gray/black
wires
Install the car audio
1 11 Purple and Right speaker (Rear)
purple/black
wires
Connect wires
2
Connect the other end of the two ISO
1
Check the car's wiring carefully, then
connectors to the car audio system. b
connect them to the two supplied ISO
3
If necessary, do other connections:
c
wires. a
Connector Connect to
Mount in the dashboard 2
1 CAN BOX
1
2 Red wire The +12V power terminal If the car does not have an on-board drive
which is live in the accessory
or navigation computer, disconnect the
(ACC) position of the
negative terminal of the car battery.
ignition switch
2
Ensure that the horizontal slant of the car
If there is no accessory
dashboard opening is between 0 and
position, connect to the
20 degrees. The unit cannot be used if
+12V car battery terminal
the dashboard opening's slant angle is
that is always live. Be sure
above 20 degrees.
to connect the black ground
3
(earth) lead to a metal surface Install the mounting bolt and place the
supplied rubber cap over the end of the
3 Orange Illumination switch mounting bolt.
wire 4
4 Black wire A metal surface of the car
First connect the black 5
Reconnect the negative terminal of the car
ground (earth) lead, then
battery.
connect the yellow and red
power supply leads.
5 Yellow wire The +12V car battery which
Turn on
is live at all times.
6 Blue wire The electric antenna control
lead or power supply lead of
Caution
the antenna booster
If there is no electric antenna Risk of road accidents! Never watch video or
or antenna booster, or it is adjust settings while you drive.
manually operated telescopic
1
antenna, it is not necessary to
Press and hold /MUTE/VOL to turn on
connect this lead.
the unit.
7 CAN BOX »
The available OSD (On-Screen Display)
8 Green and Left speaker (Rear) languages are displayed.
green/black
wires
9 White and Left speaker (Front)
white/black
wires
c
Yellow Green Blue
Gearbox
AV system
AUX
3
2
Tap [Settings].
Tap a language to select.
4
» Tap [Time].
The OSD language is changed to the
»
selected language immediately. The date/time setup menu is displayed.
To turn off the unit, press and hold /MUTE/
VOL.
Adjust screen
To adjust screen brightness
1
Press DISP/ / to show the brightness bar.
2
Tap / to adjust the value.
Set date
3
Press DISP/ / 1
Tap [Date].
To turn on/off the screen, press and hold DISP/ / .
2
Tap on the displayed date information.
»
A submenu is displayed.
3
Set date and time Tap or to set year, month and day.
Set clock mode
1
Tap the upper left corner to display the
1
Tap [Clock mode].
main menu.
2
Tap on [12Hr] or [24Hr] to select clock
mode.
Set time
1
Tap [Time].
2
Tap on the displayed time.
»
A submenu is displayed.
3
Tap or to set hour and minute.
2
Tap in the middle right side of the screen.
»
The second main menu is displayed.
Radio antenna
GPS antenna
Black
Yellow
Rear display
Wireless headphone
Amplifier
1
Insert the disc into the disc slot with the
Use map
label side facing up.
»
Play starts automatically.
Note
»
To remove the disc, press .
You may need to upgrade the map before
using it (see "Upgrade the map" section).
1 Connect USB device 4
Tap the upper left corner to display the
main menu.
1
2 Insert your USB device to the USB socket.
Tap [Navigation].
»
Play starts automatically.
»
The navigation menu is displayed in a
few seconds.
3
Refer to the map manual (in Chinese) to
Remove the USB device
operate the navigation tool.
1
Switch to another (non-USB) source.
2
Remove the USB device.
Listen to Radio
Insert SD/MMC card
1 5
Tap to display the home menu.
2
Tap [Radio].
1
Open the SD/MMC card cover.
» Band and frequency information is
2
Insert the SD/MMC card into the SD/MMC
displayed.
card slot.
»
Play starts automatically.
Remove the SD/MMC card
1
Switch to another source.
2
Press the card until you hear a click sound.
»
The card is now disengaged.
3
Remove the SD or MMC card.
3
Tap on FM or AM to select band:
4
or to tune to a radio station
by step.
Play with Bluetooth device
Play disc 3
Pair the Bluetooth-enabled devices
You can play video, audio or images stored on the
To connect your Bluetooth device to the unit, you
following discs:
need to pair the device to the unit. Pairing needs
DVD video, DVD-R, DVD-RW
only to be done once.
VCD You can pair up to eight devices.
Audio CD, CD-R, CD-RW 1
Turn on the Bluetooth function on the
device.
2
3
2
Search for Bluetooth device with the Receive call
device.
By default, all incoming calls are received
3
Select "CID3688" in the pairing list.
automatically.
4
Enter default password "0000". 1
If there is incoming call, [Incoming call...]
»
if pairing succeeds. phone call record is
displayed.
Bluetooth microphone.
2
Make a call
When conversation ends, tap (red) to
1 terminate the call.
Pair the phone with the unit.
2
Tap to display the home menu.
3
Tap [Bluetooth].
»
The Bluetooth menu is displayed.
4
Tap or to select the paired phone, then
tap .
5
Tap or to search for phone number
from the following list:
© 2010 Koninklijke Philips Electronics N.V.
Or tap to dial number directly, then tap
All rights reserved.
to dial.
CID3688_00_QSG_V1.0