Step 2 :
Move arm up to 45 degree and release . Refer diagram 9.2b
2.1 If the spring tension is in balance, arm will stay
at 45 degree. No further calibration is required.
Move arm back to horizontal position and lock
the clutch.
2.2 If the counter-weight spring is NOT balanced,
arm will either move up pr down from 45 degree
In this case, the counter-weight spring needs
to be calibrated.
If arm move up more than 45 degree, then the spring
tension is too tight and needs to be loosen.
Turn spring pin 1 & 2 clockwise
few times (3 to 4 times) to
loosen the spring untill the
arm will stay at 45 degree
If arm drop below than 45 degree, then the spring tension
is too loose and need to be tighten.
Turn spring pin 1 & 2 anti-
clockwise few times (3 to
4 times) to tighten the
spring untii the arm will
stay at 45 degree
9.3)
Spring replacement
Step 1 : Unlock the clutch
Step 2 : Move arm vertical 90 degree and release
Step 3 : Turn the spring pin clockwise to loosen the spring untill the spring fell out
Step 4 : Replace with a new spring
Step 5 : Turn the spring pin anti clockwise to tighten the spring
Step 6 : Recalibrate the spring tension
Step 7 : Lock back the clutch upon finish calibration work
10) Adjust arm angle
Sometimes the arm might be not perfect horizontal due to improper adjustment
usage wear and tear or installation at sloped ground.
Perfect horizontal line
Diagram 10a
Arm operating angle can be changed by adjusting the drive crank
13) Control Panel
12V DC
12V DC
CAPACITOR X2
MOTOR
I/P : 250V 50HZ
O/P : 12V 0.5A
12V DC
FUSE (5A F)
POWER LINE
R&G LIGHT
L
N
G
R
COM
AC 230v
L N
E
AC 230v
60Hz
MAG BR CTRL Control Panel Compatible with BR618T, 630T, 660T
Connection layout
Diagram 9.2b
Both Spring need to be
adjusted equally
Spring
Spring Pin 2
Spring Pin 1
Both Spring need to be
adjusted equally
Perfect horizontal line
Diagram 10b
LIMIT SIGNAL
SENSOR
INPUT
REMOTE
COPY/DEL
Timer Settings
ON DIP
1 ON ; 2 ON
1 OFF ; 2 ON
1
2
3
1 ON ; 2 OFF
TIMING
3 ON/OFF
6 SEC
3 SEC
1 SEC
3 sec for model BR618T, BR630T
6 sec for model BR660T
BARRIER TYPE SELECT
UP L.M
LED will turn on when
STOP
Led Indicator
-UP L.M
DOWN L.M
-STOP
-DOWN L.M
DETECTOR
-DETECTOR
-PHOTO
PHOTO
-DOWN
-UP
DOWN
-POWER
UP
PHOTO
UP
LOOP
SIGNAL
LIMIT
INPUT
OUTPUT
PWR
FAN
PHOTO
DOWN
SPECIAL
VEHICLES
-
+ GND
POWER
LIMIT
FOR
DETECTOR
4
8
5
OUTPUT
OUTPUT
MOTORCADE
SIGNAL
5MM
12ACV
SERIAL
COMMUNICATION
Loop
detectcor
Manual
Push
Button
Infrared sensor
Loop Coil
10.1)
Arm not at horizontal position
10.2) If arm still not at desired position, please adjust Drive Crank
Step1: Turn the Edge-screw anti clockwise to
loosen drive crank for adjustment.
Step2:
2.1)
If arm above the horizontal line (diagram 10c),
turn drive crank clockwise to adjust the arm lower.
2.2)
If arm below the horizontal line (diagram 10c),
turn drive crank anti-clockwise to adjust the arm higher.
Step 3:
Turn the screw back to hold the newly adjusted drive crank position.
11) How to reduce arm jerking?
Adjust screw to maintain 3mm gap with rubber
cushion.
Screw
Rubber
Cushion
12) Loop detector installation guide
12.1)
Loop wire winding
12.2)
Depth of groove
5 turns loop cable
When winding the wire inside the loop please make sure is not twisted. All wire in the groove
have to run almost perfect parallel with each other. Only twist the wire then wire when wire
going back to Loop Detector.
14) Surge protector installation
It is COMPULSORY to install surge protector when installing barrier gate outdoor. All installed
surge protector must be connected to EARTH. All metal housing of equipments also must
connected together to EARTH to achieve Common Earth. Please use at least 2.5mm wire for
EARTH connection wiring. All these are important steps to protect barrier gate from being
damaged by lightning surge. Waranty does not cover damages by lightning surge.
Timer - Auto Close
5 seconds
10 seconds
20 seconds
NOT USE
-When barrier arm is lifted UP
-When STOP button is pressed
-When barrier arm is lifted DOWN
-When Detector detected vehicles
-When PHOTO bean detected obstacle
-When DOWN button is pressed
-When UP button is pressed
-When POWER is ON.
Up
Stop
Down
Step 1:
Loose up the screw position limit then adjust
Ir position sensor Control panel
the position until barrier arm allign with
sensor
Ir position sensor
Step 2:
Tighten back the screw position limit after
Position limit
done complete adjusment.
Screw to release and tight
Step 3:
position limit
Testing
Led sensor light
Re-adjust the position limit.
Screw 2
Rubber cushion
to reduce vibration
Gap 3mm
Nominal groove width : 4mm
Nominal groove depth : 30mm to 50mm
Refer to diagram 12.1, you can use 1.5mm²
or 16awg stranded wire and wind minimum
5 turns inside the groove. Then "TWIST' the
wire back to Loop Detector.
Diagram 12.1
Caution:
When you put silicon to fill up the groove, make sure you press
tightly downward. This is to ensure that there is all wire is
pressed down together and no space for them to move inside
the groove. This caution is to ensure reliability, if loop wire can
move inside the groove due to vibration when pass through, it
will be unstable.
Diagram 12.2
barrier
open
close
operation.
Edge screw
Drive crank
Edge screw
Diagram 10c
Screw 1
Diagram 11
Need help?
Do you have a question about the BR600T Series and is the answer not in the manual?
Questions and answers