Table of Contents
Advertisement
Available languages
Available languages
3.0 BRIEF INTRODUCTION
Your welder belongs to a range of welding
inverters for MMA - Manual Metal Arc Wel-
ding that adopts the latest pulse width mo-
GXODWLRQ 3:0 WHFKQRORJ\ DQG WKH LQVXODWHG
JDWH ELSRODU WUDQVLVWRU ,*%7 SRZHU PRGXOH
to grant optimal performances: constant cur-
rent output to make welding arc more stable
DQG VWHSOHVV FXUUHQW UHJXODWLRQ $OO LQYHUWHUV
DUH ¿WWHG ZLWK DXWRPDWLF SURWHFWLRQ IXQFWLRQV
overvoltage, overcurrent and overtemperatu-
UH
3.1 TECHNICAL DATA
NOTE: here below data may differ from
the data on the technical table on the unit.
Always refer to the technical data table on
the unit.
W130
(1 ph)
230V 50/60Hz
KVA
Power 60%
2,7
V
Uo
60
A ±10%
Amp. Min-Max
5 ÷ 130
20% 130
A
Amp. 60974-1
60% 75
mm
Ø E
1,6 ÷ 3,25
-
Insulation
H
-
Protec. Degree
IP22
W160
(1 ph)
230V 50/60HZ
KVA
Power 60%
4,2
V
Uo
65
A ±10%
Amp. Min-Max
5 ÷ 160
Amp.
30% 160
A
60974-1
60% 115
mm
Ø E
1,6 ÷ 4
-
Insulation
H
-
Protec. Degree
IP22
W200
(1 ph)
230V 50/60HZ
KVA
Power 60%
6
V
Uo
65
A ±10%
Amp. Min-Max
5 ÷ 200
Amp.
25% 200
A
60974-1
60% 120
mm
Ø E
1,6 ÷ 5
-
Insulation
H
-
Protec. Degree
IP22
4.0 INSTALLATION OF THE
EQUIPMENT
Proper operation of the generator is ensu-
red by adequate installation. The assem-
bly of the inverter must be done by expert
people, following the instructions and in
full respect of the safety standards.
5HPRYH WKH ZHOGHU IURP WKH FDUWRQ ER[
BEFORE ATTEMPTING ANY ELECTRI-
CAL CONNECTION CHECK THE DATA
PLATE AND MAKE SURE THAT THE IN-
PUT VOLTAGE AND THE FREQUENCY
ARE THE SAME OF THE MAINS OUTLET
TO BE USED.
EARTHING
- To protect users the welding machi-
nes must be connected properly to the
earth (ground) system (INTERNATIONAL
SAFETY REGULATIONS).
- It is indispensable to earth (ground)
the machine properly with the yellow-
green conductor of the power supply ca-
ble, in order to avoid discharges due to
accidental contacts with earthed objects.
- The chassis (that is conductive) is
electrically connected to the earth con-
ductor. Failure to earth the equipment
correctly can cause electric shocks dan-
gerous to the users.
3OXJ WKH LQYHUWHU WR WKH PDLQV
Do not use the generator with input ca-
bles’ extensions longer than 10m and
thinner than 2.5mm². Remember to keep
them layed and not wound or entangled.
Do not use the welder with the side panels
partially or completely removed in order
to avoid accidental contacts with inner
live parts.
7KH LQYHUWHU LV QRZ UHDG\ IRU XVH 0DNH
sure you are welding in a properly ventilated
area and that the ventilation openings of the
machine are not obstructed (poor air ventila-
tion may reduce the duty cycle of the unit and
FDXVH GDPDJHV 1RZ \RX PD\ FKRRVH WKH
welding process by connecting the accesso-
ULHV DV VKRZHG LQ WKH IROORZLQJ SDJHV
Page 7
Hide quick links:
Advertisement
Table of Contents
