Philips AZ1066/96 User Manual

Register your product and get support at
www.philips.com/welcome
AZ1066
ZH-TW
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
AZ1066_96_UM_V1.1_wk1121.2
EN
1 Important
Safety
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
h Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
i Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
j Only use attachments/accessories specified by the manufacturer.
k Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
l Unplug this apparatus during lightning storms or when unused for long
periods of time.
m Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
n Battery usage CAUTION – To prevent battery leakage which may result in
bodily injury, property damage, or damage to the unit:
•
Install all batteries correctly, + and - as marked on the unit.
• Do not mix batteries (old and new or carbon and alkaline, etc.).
• Remove batteries when the unit is not used for a long time.
•
The batteries shall not be exposed to excessive heat such as sunshine, fire
or the like.
o Apparatus shall not be exposed to dripping or splashing.
p Do not place any sources of danger on the apparatus (e.g. liquid filled
objects, lighted candles).
Warning
•
Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
•
Never place this apparatus on other electrical equipment.
•
Keep this apparatus away from direct sunlight, naked flames or heat.
• Never look into the laser beam inside this apparatus.
•
Ensure that you always have easy access to the power cord, plug or adaptor to disconnect
this apparatus from the power.
• Where the MAINS plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
Caution
• Use of controls or adjustments or performance of procedures other than
herein may result in hazardous radiation exposure or other unsafe operation.
2 Your CD Soundmachine
Congratulations on your purchase, and welcome to Philips! To fully benefit from the
support that Philips offers, register your product at www.philips.com/welcome.
Introduction
With the CD Soundmachine you can
•
play audio disc
•
play cassette tape
• listen to FM/MW radio
• recording music/voice to tape.
•
You can also enhance the sound with the Dynamic Bass Boost feature.
What's in the box
Check and identify the contents of the package:
• CD Soundmachine
•
AC power cord
•
User Manual
Overview of the main unit
a b c d e f g h
i
k
j
a Source selector: CD, TUNER, MP3 LINK,TAPE/OFF
•
Select source: CD, radio, MP3 or Tape
• Switch to standby mode
b VOLUME
•
Adjust volume level
c DBB
• Turn the bass enhancement on/off
d Cassette recorder buttons
•
Pause play or record
•
/
Stop cassette play or record
Open the cassette holder
•
Fast forward
•
Fast rewind
•
Start cassette play
•
Start cassette record
e LIFT TO OPEN
• Open/Close the CD compartment
f MP3 LINK
• Socket for audio input
g TUNING +/-
•
Tune to radio stations
h FM/MW/
• Select radio band: FM or MW
•
Switch to Repeat mode.
i CD buttons
•
Stop CD play
Erase a CD program
•
/
Select the previous/next track
Fast search backward/forward within the current track
•
Start or pause CD play
•
Select a play mode: REPEAT or SHUFFLE
•
Program tracks and browse the program
j Repeat function buttons
•
Repeat the previous 120 seconds' CD or tape content
•
Record voice
•
Play the recorded voice
Play both the recorded voice and repeat content for comparison
•
Cancel repeat and start playing CD or tape
k Built-in microphone
3 Get started
Caution
•
Use the controls only as stated in this user manual.
•
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number of your player.
The model number and serial number are on the bottom of your player. Write the
numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
1
Open the battery compartment.
6 x 1.5V R-14/UM-2/C-cell
2
Insert 6 x 1.5V R14/UM-2/C-cell batteries with correct polarity (+/-) as indicated.
3
Close the battery compartment.
Tip
•
If you want to save battery life, use the supplied power cord.
Connect AC power
Warning
• Risk of product damage! Ensure that the power supply voltage corresponds to the voltage
printed on the back or the underside of the product.
• Risk of electric shock! When you unplug the AC adaptor, always pull the plug from the
socket. Never pull the cord.
Note
•
Install the unit near the power supply socket and where the AC power plug can be easily
reached.
1
Connect the power cord to the AC MAINS~ socket on the CD Soundmachine
and to the power supply socket.
•
To switch the CD Soundmachine off completely, disconnect the power
cord from the power supply socket.
Tip
•
To save energy: After use, set the source selector to OFF. To turn off the CD
Soundmachine completely, disconnect the plug from the power supply socket.
4 Play a CD
Note
•
You cannot play CDs encoded with copyright protection technologies.
You can play commercially available audio:
• CDs
• CD-Recordables (CD-R)
•
CD-Rewritables (CD-RW)
1
Switch the source selector to CD.
2
Lift the lid of the CD compartment.
3
Insert a CD with the printed side facing up.
4
Close the CD lid gently.
»
The total number of tracks is displayed.
5
Press to start play.
»
[ ] is displayed.
•
To pause CD play, press .
•
To resume CD play, press again.
• To stop CD play, press .
Select a track
1
During play, press / to select a track.
Find a passage within a track
1
During play, press and hold / .
»
The CD is played at high speed and with reduced volume.
2
Release / to resume normal play.
Tip
•
When search reaches the end of the last track, the CD stops.
Program play sequence
You can store up to 20 tracks in the desired sequence.
1
In stop mode, press to start to program play sequence.
»
[PROG] and [00] are displayed.
2
Press / to select a track.
3
Press to store the track.
PROG
4
Repeat steps 2 to 3 to select and store all tracks.
»
When all 20 tracks are stored, no more tracks can be selected and the
display shows [---].
5
To play program, press .
• In stop mode, press repeatedly to browse stored tracks.
•
To cancel program, press twice.
Tip
•
When program play stops, the CD Soundmachine returns to normal play. To play
program again, repeat steps 1 to 5.
Repeat play
You can repeat a track, a disc, or a program.
•
[ ] – plays the current track continuously
•
[ ALL] – repeats the entire CD/program
1
During play, press repeatedly until the display
shows the repeat icon.
• Repeat one track.
• Repeat the entire CD.
• To stop repeat play, press repeatedly until ALL
the repeat icon is no longer displayed.
Shuffle play
You can play all tracks in random order.
1
During play, press repeatedly until the display
shows the shuffle icon.
• To stop shuffle play, press again.
5 Play cassette recorder
1
Switch the source selector to TAPE/OFF.
2
Press to open the cassette holder.
3
Insert a cassette tape with the full reel on right side, and then close the
cassette holder.
4
Press to start play.
• To pause play, press .
• To stop the play, press .
Find a passage within a tape
1
During stop, press / to search for a desired passage in a tape.
2
To stop fast search, press .
Record from CD
1
Switch the source selector to CD.
2
Insert a CD with the printed side facing up.
3
If you want to record tracks in the desired sequence, program the desired
tracks. (See 'Program play sequence' section)
4
Press to open the cassette holder.
5
Insert a blank cassette, and close the holder.
6
Press to start to record.
• To pause, press .
•
To resume, press again.
• To stop, press .
Record from radio
1
Switch the source selector to TUNER.
2
Tune to a radio station.
3
Press to open the cassette holder.
4
Insert a blank cassette with the full reel on the right side, then close the holder.
5
Press to start to record.
• To pause, press .
•
To resume, press again.
• To stop, press .
6 Use Learning function
When you are listening to CD or tape, you can let the CD soundmachine to play
repeatedly the last played 120 seconds' content. You can also record down your own
voice for comparison. This is especially useful for language learning or whatever.
1
Switch the source selector to CD or TAPE/OFF.
2
Set FM/MW/ switch to mode.
3
Press or to start play.
»
The red light under the button illuminates.
»
The CD soundmachine starts recording what is played onto its built-in
memory. Maximum recording length is 120 seconds.
Listen to the recorded content repeatedly
1
Press .
»
The red light under button illuminates.
»
CD or Tape stop playing. It plays the recorded content repeatedly.
2
To pause, press .
• To resume, press again.
Tip
•
if you want the CD soundmachine to start record on other position, play the source at
the position you want and then press to start the recording again and replace the
previous recording.
Record your voice
Note
• To ensure recording quality, keep the distance between you and the
microphone within 30cm.
•
The maximum recording length is also 120 seconds.
1
Press .
»
The red light under the button illuminates.
2
Speak/sing to the built-in microphone which is located on the top side of the
left speaker.
•
To erase what's recorded, press again.
Speak/sing to the microphone to record new content.
Compare your voice with the original recording
1
Press briefly.
»
The red light under the button illuminates. It plays the record of your
voice repeatedly.
»
To pause, press . Press again to resume repeatedly playing.
2
Press for more than 3 seconds.
»
It plays both the recorded voice and the original recording repeatedly.
Exit Learning mode
To stop Repeat, recording or comparing, press .
»
CD or Tape resume playing.
To exit Learning mode
1
Switch FM/MW/ to FM or MW position.
7 Listen to radio
1
Switch the source selector to TUNER.
2
Switch BAND to FM or MW.
3
Turn TUNING +/- to find a station.
Tip
• To improve FM reception, you can extend, incline or turn the telescopic
antenna for best reception.
• To improve MW reception, turn the CD Soundmachine to face a different direction.
8 Troubleshooting
Warning
• Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the following points before
requesting service. If the problem remains unsolved, go to the Philips web site (www.Philips.
com/support), or contact Philips (see Contact information). When you contact Philips,
ensure that the apparatus is nearby and the model number and serial number are available.
No power
• Ensure that the power cord is connected securely.
• Ensure that there is power at the power supply socket.
• Ensure that the batteries are installed correctly.
No sound
• Adjust the volume.
• Check if it's in Repeat mode.
• Ensure that the track played is of a compatible format.
Display does not function properly./No reaction to operation of any of the controls.
1
Disconnect the AC power cord.
2
Connect the AC power cord after a few seconds.
Cannot play disc
• Ensure that the disc label is inserted with the printed side facing up.
• Wipe the disc with fibre cleaning cloth from the centre to the edge in a straight line.
• This disc may be defective. Play another disc.
• Ensure that the CD is a finalised CD/CD-R/CD-RW.
• Ensure that the laser lens is clean.
• Ensure that the CD is not encoded with copyright protection technologies.
The CD skips tracks
• Ensure that the CD is not damaged or dirty.
• Ensure that program/shuffle mode is deactivated.
Poor cassette sound quality
• Ensure that heads in the cassette holder are clean.
• Ensure that a NORMAL (IECI) cassette tape is used for record.
Cassette does not work for record
•
Ensure that cassette tabs are not broken.
•
Check if it's in Repeat mode. If yes, exit Repeat mode first. (See 'Play Repeat
function' section).
9 Product information
Note
• Product information is subject to change without prior notice.
Dimensions (Main unit) 291 x 146 x 243 mm
(W x H x D) 11.5 x 5.8 x 9.6 inches
Weight (Main unit) 1.8 kg
3.8 pound
Power supply DC 9V 1.5 A
AC 110-127/220-240 V~
Power consumption Active 12W
Standby < 2W
Power output 2 x 1W RMS
Operating temperature range -10°C - +50°C
14°F - 122°F
10 Notice
Recording and playback of material might require consent. See Copyright Act 1956 and
The Performer's Protection Acts 1958 to 1972.
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound
recordings, may be an infringement of copyrights and constitute a criminal offence. This
equipment should not be used for such purposes.
This apparatus includes this label:
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Electronics may void the
user's authority to operate the equipment.
Warning
•
Keep this apparatus away from direct sunlight, naked flames or heat.
Your product contains batteries covered by the European Directive 2006/66/EC, which
cannot be disposed of with normal household waste.
When you see the crossed-out wheel bin symbol with the chemical symbol 'Pb', it
means that the batteries comply with the requirement set by the directive for lead:
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially negative
consequences on the environment and human health.
Recycling
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a product, it means the
product is covered by the European Directive 2002/96/EC:
Never dispose of your product with other household waste. Please inform
yourself about the local rules on the separate collection of electrical and
electronic products. The correct disposal of your old product helps prevent
potentially negative consequences on the environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging
easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and
polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by
a specialized company. Please observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
Never use solvents such as benzene, thinner, cleaners available commercially, or anti-
static sprays intended for discs.
Note
•
The type plate is located on the bottom of the apparatus.