C Pair The Watch With A Phone; Auto Time Adjustment; Viewing Stopwatch Data - Casio 5604 Operation Manual

C Pair the watch with a phone.

Before you can use the watch in combination
with a phone, you first need to pair them.
1.
Move the phone to be paired with close to
(within one meter of) the watch.
2.
Y Tap the "EDIFICE Connected" icon.
3.
Y Perform the operation shown on the
screen of the phone to be paired with.
If a pairing prompt message appears,
●
perform the operation shown on the
phone screen.
About two seconds after pairing starts,
●
the second hand will point to [R]. When
pairing is complete, the second hand
will move to e .
Note
The first time you start up EDIFICE
●
Connected, a message will appear on
your phone asking if you want to
enable location information
acquisition. Configure settings to allow
background use of location
information.

Auto Time Adjustment

The watch will connect with a phone at preset
times each day and adjust its time settings.
Using Auto Adjust
●
Your watch adjusts its time setting four times
a day according to a preset schedule. If you
leave the watch in the Calendar Mode, it will
perform the adjustment operation
automatically as you go about your daily life,
without any operation required by you.
Operation Guide 5604
Important!
The watch may not be able to perform
●
auto time adjustment under the
conditions described below.
While the watch is too far away from
ー
its paired phone
While communication is not possible
ー
due to radio interference, etc.
While the phone is updating its
ー
system
While EDIFICE Connected is not
ー
running on the phone
Note
If the watch does not indicate the
●
correct time even if it is able to connect
with a phone, adjust the hand and day
indicator positions.
Adjusting Hand and Day Indicator
l
Alignment
If there is a World Time City specified
●
with EDIFICE Connected, its time will
also be adjusted automatically.
The watch will connect with the phone
●
and perform auto time adjustment at
around 12:30 a.m., 6:30 a.m., 12:30
p.m. and 6:30 p.m. The connection is
automatically terminated after auto
time adjustment is complete.
Triggering Immediate Time Adjustment
●
The watch's time setting will be adjusted
automatically whenever you establish a
connection between the watch and a phone.
Whenever you want to adjust the watch's time
setting based on your phone's time, perform
the procedure below to connect with a phone.
1.
Move the phone close to (within one meter
of) the watch.
2.
X Enter the Calendar Mode.
Navigating Between Modes
l
3.
X Hold down (B) for at least 0.5 seconds
until the second hand points to [R].
Release the button as soon as the second
hand points to [R].
When the watch connects with a phone,
the second hand will normally move to e
and then the watch's time setting will be
adjusted.
The connection is terminated
●
automatically after time adjustment is
complete.
Connected

Viewing Stopwatch Data

This section explains how to send lap times
(up to 200 records) that are stored in watch
memory, as well as other data to your phone
for viewing with EDIFICE Connected.
Sending Stopwatch Data to a Phone
●
Use the procedure below to send data from
the watch to a phone.
1.
2.
3.
Checking a Lap Time
●
Use EDIFICE Connected to check the data
you sent to the phone.
1.
2.
Note
●
After time adjustment
Y Tap the "EDIFICE Connected" icon.
X Hold down (B) for at least two seconds
until the second hand points to [R] twice.
This establishes a connection between
the watch and phone.
Y Perform the operation shown on the
phone screen to transfer data measured
by the watch to the phone.
After data transfer is complete, a list of the
measurement data will appear on the
phone display.
Tapping a stopwatch data item displays
●
its details.
Y Tap the "EDIFICE Connected" icon.
Y Perform the operation shown on the
phone screen to view the measurement
data you want.
Tapping "Edit" displays a screen that
you can use to change the data item
title and to delete lap time data.
7