Related Manuals for Philips MC146/05
Summary of Contents for Philips MC146/05
- Page 1 MC146 Micro Hi-Fi System Register your product and get support at www.philips.com/welcome User manual...
- Page 2 Important notes for users in the U.K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Remove fuse cover and fuse. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A.
- Page 3 PULL TO OPEN STANDBY-ON M I C RO S Y S T E M M C 1 4 6 CD/CD - R/CD - RW COMPATIBL E SOURC E TUNING REPEAT PROG PRESE T &...
-
Page 4: Table Of Contents
Contents General Information Supplied accessories ... 5 Environmental Information ... 5 Safety Information ... 5 Hearing Safety ... 6 Preparations Rear connections ... 7 Inserting batteries into the Remote Control ..8 Using the Remote Control to operate the system ... -
Page 5: General Information
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/ welcome. This product complies with the radio interference requirements of the European Community. Supplied accessories – 2 speaker boxes –... -
Page 6: Hearing Safety
General Information Hearing Safety Listen at a moderate volume. ● Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. -
Page 7: Preparations
FM wire antenna speaker (right) Rear connections The type plate is located at the rear of the system. For users in the U.K.: please follow the instructions on page 2. Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. -
Page 8: Inserting Batteries Into The Remote Control
Preparations Inserting batteries into the Remote Control Open the battery compartment. Insert two R03 or AAA batteries following the indications (+/-) inside the compartment. Close the cover. Using the Remote Control to operate the system Aim the Remote Control directly at the remote sensor (IR) on the front panel. -
Page 9: Controls Available On The Remote Control Only
Controls on the system and remote control STANDBY-ON2 (POWER) – switches the system to standby or on. iR SENSOR – infrared sensor for remote control. SOURCE – selects the respective sound source for CD/ TUNER/AUX. – switches on the system. PRESET +/- for radio ... -
Page 10: Basic Functions
Basic Functions STANDBY-ON MIC RO S Y STE M MC14 6 CD/CD - R/CD - RW COMPATIBL E SOURC E TUNING PRESE T IMPORTANT: Before you operate the system, complete the preparation procedures. Switching the system on ● Press STANDBY -ON 2 or SOURCE (POWER on the remote control). -
Page 11: Cd Operation
STANDBY-ON MIC RO S Y STE M MC14 6 CD/CD - R/CD - RW COMPATIBL E SOURC E TUNING PRESE T IMPORTANT: The lens of the CD player should never be touched. Loading a disc This CD player plays Audio Discs including CD- Recordables and CD-Rewritables. -
Page 12: Different Play Modes: Shuffle And Repeat
CD Operation Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. The play modes cannot be combined with PROGRAMME. SHUF ... tracks of the entire disc are played in random order. REP ALL ... -
Page 13: Radio Reception
STANDBY-ON MIC RO S Y STE M MC14 6 CD/CD - R/CD - RW COMPATIBL E SOURC E TUNING PRESE T Tuning to radio stations Press SOURCE on the set repeatedly or press TUN on the remote control repeatedly until the desired waveband (FM or MW) is displayed. -
Page 14: Other Connection
Cleaning the disc lens ● After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner. -
Page 15: Clock/Timer
STANDBY-ON MIC RO S Y STE M MC14 6 CD/CD - R/CD - RW COMPATIBL E SOURC E TUNING PRESE T Setting the clock In standby mode, press and hold CLOCK/ DISPLAY on the remote control set for 2 seconds. Press PROG to select 12-hour or 24-hour display. -
Page 16: Specifications
Specifications AMPLIFIER Output power ... 2 x 2W RMS Signal-to-noise ratio ... ≥ 60 dBA (IEC) Frequency response ... 125 – 16000 Hz Impedance loudspeakers ... 8Ω CD PLAYER Frequency range ... 125 – 16000 Hz Signal-to-noise ratio ... 65 dBA TUNER FM wave range ... -
Page 17: Troubleshooting
Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. -
Page 18: Troubleshooting
Troubleshooting Problem The remote control does not function properly. The time is not working. The Clock/Timer setting is erased. Solution ✔ Select the source (CD or TUNER, for example) before pressing the function button (É,í,ë). ✔ Reduce the distance between the remote control and the system. - Page 19 Meet Philips at the Internet http://www.philips.com MC146 CLASS 1 LASER PRODUCT © 2010 Koninklijke Philips Electronics N.V. All rights reserved. Printed in China MC146_05_UM_V2.0...