Remote Controller Installation; Optional Kit Installation (Option) - Fujitsu AGU9RLF Installation Manual

Indoor unit (floor type)
Hide thumbs Also See for AGU9RLF:
Table of Contents

Advertisement

[Operation method]
● For the operation method, refer to the operating manual.
● The outdoor unit, may not operate, depending on the room temperature. In this
case, keep on pressing the MANUAL AUTO button of the indoor unit for more than
10 seconds. The operation indicator lamp and timer indicator lamp will begin to fl ash
simultaneously during cooling test run. Then, heating test run will begin in about three
minutes when HEAT is selected by the remote control operation. (Please follow the
operating manual for remote control operation.)
● To end test operation, press the remote controller START/STOP button.
(When the air conditioner is running by pressing the test run button, the OPERATION
Lamp and TIMER Lamp will simultaneously fl ash slowly.)
[Using the wired remote control] (Option)
● For the operation method, refer to the operating
manual.
(1) Stop the air conditioner operation.
(2) Press the master control button and the fan
control button simultaneously for 2 seconds or
more to start the test run.
(3) Press the start/stop button to stop the test run.
Test run display

10. REMOTE CONTROLLER INSTALLATION

CAUTION
Check that the indoor unit correctly receives the signal from the remote controller, then
install the remote controller holder.
Select the remote controller holder selection site by paying careful attention to the
following:
Avoid places in direct sunlight.
Select a place that will not be affected by the heat from a stove, etc.
10.1. Remote controller holder installation
• Install the remote controller a maximum distance of 6 m (19 ft.) from the remote
control receiver. However, when installing the remote controller, check that it operates
correctly.
• Install the remote controller holder to a wall, pillar, etc. with the tapping screw.
Remote controller
Remote controller
holder fi xing
mounting
Remote controller
holder
(1) Set
Tapping
screw
Remote
(small)
controller
(2) Down

11. OPTIONAL KIT INSTALLATION (OPTION)

This air conditioner can be connected with the following optional kits. Refer to each
installation manual for the method of installing optional parts.
• Wired remote controller
• Simple remote controller
• External connect kit
]
11.1. Before install optional remote controller
• When you use optional remote controller, some functions may not be used.
• Please use the recommended optional remote controller.
CAUTION
Before installing, be sure to disconnect all power supply.
Don’t touch the heat exchanger.
During installing or removing operation, be sure not to have wire caught by parts or
draw it hard. Or it may result troubles to the air-conditioner.
Avoid place in direct sunlight.
Select place that will not be affected by the heat from a stove, etc.
Before setting up the optional kit, please confi rm whether air-conditioner can receive
the signal.
Do not connect the optional remote controller to the terminal for power supply.
When connecting the optional remote controller with the indoor unit, please use the
connecting cable packaged up with the optional remote controller.
Recommended cable length of optional remote controller is 10 m (33 ft). Make sure to
do insulate of connecting part when extended the cable.
]
11.2. Remote controller cable modifi cation
(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then
1
remove the insulation from the cut end of the cable.
(2) Connect the remote controller cable and connecting cable. (Supplied with wired remote
controller)
Important: Be sure to solder wires to connect. Be sure to insulate the connection between
the wires.
Connecting cable
White
Red
Black
White
Remote
Red
controller cable
Insulated
Remote
connection
controller cable
Black
11.3. External input / output Wire modifi cation
(1) Remove insulation from wire attached to wire kit
Option parts
connector. Remove insulation from fi eld supplied
External input/
cable. Use crimp type insulated butt connector to
output wire
join fi eld cable and wire kit wire.
(2) Connect the wire and Field supply wire.
(Supplied with external connect kit)
Insulated
Important:
connection
Be sure to solder wires to connect. Be sure to
Cable
insulate the connection between the wires.
(Field supply)
]
1
11.4. Side panel L and control cover removal
(1) Refer to “6.3. Side panel L, R removal and installation” to remove the side panel L.
(2) Remove the control cover.
(3) Remove the control inner cover.
PCB
Control
inner cover
Control cover
]
En-9

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents