Page 1
Keysight 85331B/85332B Solid State Switch Operating and Service Guide...
Page 2
Conformity. understood and met. where in the EULA. Keysight shall be under no obligation to update, revise or otherwise modify the Software. With WARNING respect to any technical data as defined by FAR 2.101, pursuant to FAR...
To return this unwanted instrument, contact your nearest Keysight Service Center, or visit http://about.keysight.com/en/companyinfo/environment/takeback.shtml for more information. Sales and Technical Support To contact Keysight for sales and technical support, refer to the support links on the following Keysight websites: – www.keysight.com/find/switches (product-specific information and support, software and documentation updates) –...
Page 4
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 85331B/85332B Operating and Service Guide...
List of Figures Figure 1-1 85332B (left) and 85331B (right) solid state switches Figure 1-2 A typical multiple-channel, multiple-frequency system configuration ......13...
Page 8
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 85331B/85332B Operating and Service Guide...
..... .12 Table 2-1 Optional accessories for 85331B and 85332B solid state switches ........22...
Page 10
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 85331B/85332B Operating and Service Guide...
Page 11
Keysight 85331B/85332B Solid State Switch Operating and Service Guide Introduction General Information This chapter introduces the 85331B and 85332B solid state switches and gives a brief overview of the drive levels and switch operation logic.
Introduction General Information Solid state switch overview The Keysight 85331B and 85332B are PIN diode based solid state switches which provide superior performance in terms of fast switching speed, high isolation, and broad operating frequency range. Figure 1-1 85332B (left) and 85331B (right) solid state switches Table 1-1 shows the two models of solid state switches available.
Page 13
AUT (Antenna under test) is illustrated in Figure 1-2. The 85331B and 85332B do not contain a switch control unit. If your system is NOTE configured with an 85330A multiple channel controller, the switch control unit must be ordered separately (Keysight part number 85331-60121).
Only one port can be turn ON at a time, or all ports can be OFF. The total current NOTE is approximately 480 mA for 85332B and 240 mA for 85331B with all ports OFF. Keysight 85331B/85332B Operating and Service Guide...
Pin 1 = Port 1 on/off bias Pin 2 = Port 2 on/off bias Pin 3 = Port 3 on/off bias (not connected for 85331B) Pin 4 = Port 4 on/off bias (not connected for 85331B) Pin 5 = Common/ground (0 VDC)
Page 16
Introduction THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK. Keysight 85331B/85332B Operating and Service Guide...
Page 17
Operating Guides Installation Operating Instruction Performance Tests Optional Accessories This chapter describes the installation procedures and operating instructions of the 85331B and 85332B solid state switches. The procedures for checking the electrical performance of the solid state switches are also provided.
Keysight Technologies can provide packaging materials identical to the original materials. Refer to Service and Support information in the front matter of this manual for the Keysight Technologies nearest to you. Attach a tag indicating the type of service required, return address, model number and serial number.
The S21 (insertion loss) measurement is the best way to determine if the switch is faulty by applying the appropriate bias voltage to the bias connector. Figure 2-1 Connection to perform quick check Keysight 85331B/85332B Operating and Service Guide...
Page 20
3 If RF2 is connected to Port 2, apply -7 Vdc to Pin 2 of bias connector (Refer to Figure 2-1) and +6.3 Vdc to Pin 1. For 85332B, repeat the above steps until all four ports are tested. NOTE Keysight 85331B/85332B Operating and Service Guide...
The solid state switches do not have internal adjustments and should not be opened. Repair The 85331B and 85332B solid state switches are not recommended for repair as most components are not easily removed. Maintenance The connectors, particularly the connector faces, must be kept clean.
Operating Guides Optional Accessories Table 2-1 lists the optional accessories for Keysight 85331B and 85332B solid state switches. Table 2-1 Optional accessories for 85331B and 85332B solid state switches Description Keysight part number Switch control cable - 1 meter 85331-60125...
Need help?
Do you have a question about the 85331B and is the answer not in the manual?
Questions and answers