1. Manuals
  2. Brands
  3. EOS Manuals
  4. Control Panel
  5. ECON H1
  6. Installation and user manual

EOS ECON H1 Installation And User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and user's manual
ECON H1
GB
IP x4
Druck Nr. 29342787en / - 22.06
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ECON H1 and is the answer not in the manual?

Questions and answers

Related Manuals for EOS ECON H1

Summary of Contents for EOS ECON H1

  • Page 1 Installation and user's manual ECON H1 IP x4 Druck Nr. 29342787en / - 22.06...

  • Page 2: Table Of Contents

    Contents General information Operation Technical Data 3.1.1 Dry (Finnish) sauna Package contents Steam operation General safety precautions 3.2.1 Supplemental heating function 3.2.2 Low water shutoff Assembly of the control unit Wall mounting Troubleshooting Electrical connection 4.1.1 Error indicator in display 2.2.1 Connecting the sauna oven Overheat safety shutoff 2.2.2 Connecting the vaporizer...

  • Page 3: Package Contents

    1.2 Package contents 2. Assembly of the control unit (subject to change) 2.1 Wall mounting Included with the control unit are 1. an oven-sensor board with overheat Mount the control unit outside the sauna shutoff protection, KTY-sensors with cabin only. The most practical mounting sensor housing, two 3x25 mm fastening point would be the wall area onto which screws and a 1,7 m long sensor cable.

  • Page 4: Electrical Connection

    threaded holes Please note: upper threaded hole If the sauna cabin is not equipped with electrical conduits, the electrical cables must be lead along the outside of the cabin, preferably in one of the recesses between the wood boards. Therefore, you have to mount the control unit farther away from the cabin wall, so you can lead the cables into the unit.

  • Page 5: Connecting The Sauna Oven

    In general, there can only be one perma- Warning: Always connect the sauna nent connection to the power supply network, oven's neutral conductor. During to include a device which allows the unit to steam operation one of the phases be disconnected from the power source with shuts down, therefore the heat doesn't a contact distance of at least 3 mm from all spread evenly.

  • Page 6: Connecting The Sauna Lamp

    Please Warning: When connecting the vaporizer note that following measurements are based on values make sure it is correctly attached to the provided by the unit quality assurance by water bath (WB) and low water shutoff the European Standard EN 60335-53-2. In (WM).
  • Page 7 sensor hole board sauna ceiling sensor housing sensor line center sensor housing on middle section shutoff sensor housing terminals in the Illust. 10 control unit 2. Drill a hole to lead the cable through, Illust. 11 preferably through the middle of one of the wooden boards.

  • Page 8: Operation

    3. Operation The green LED above the button will light up. Depending on the current temperature The control unit is intended for two in the sauna cabin, the sauna oven's red operational modes: Å operational display will light up, signaling - Dry (Finnish) sauna the oven is heating.
  • Page 9 Operation using the vaporizer function is In the case of the symmetrically wired oven Ä (equal heating power for each phase), one- activated via the middle CLIMA key . The third of the heating power of the sauna oven value set for the last operating cycle is consequently switched off.

  • Page 10: Supplemental Heating Function

    Temperature in °C Please note: Some vaporizers are equipped with a buzzer, providing an acoustical signal as an additional warning when the thermostat in the vaporizer sauna registers a water deficit. herbal/steam-warm air bath 4. Troubleshooting warm-air bath Unit cannot be put in operation mode Check to see whether socket (230V AC) is in contact with all three prongs.

  • Page 11: Heating Time Extension

    5. Heating time extension After such a shutdown, the overheat safety shut off must be replaced and the sauna The control unit is adjusted for a maximum unit or the control unit monitored by an ex- heating time of 6 hours at delivery. This pert.

  • Page 12: Guarantee

    Service Address: Outside of Germany please contact your specialist EOS-Werke Günther GmbH dealer in case of warranty claims. Direct warranty Adolf-Weiß-Str. 43 processing with our service department is in this case not possible.

Table of Contents