Honeywell GENT Nano panel-based Commissioning Instructions page 3

Difference between Nano panel at V1.3X and V2.4X - - - - - - - - 36
New features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 36
New functions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 36
Changed Functionality - - - - - - - - - - - - - - - - - - - - - - - - - - - 36
How to view or change 'Device configuration' - - - - - - - - - - - 37
Typical device forms - - - - - - - - - - - - - - - - - - - - - - - - - - - - 38
Typical device forms continued - - - - - - - - - - - - - - - - - - - - - - - 39
Sensor States - - - - - - - - - - - - - - - - - - - - - - - - - - - 40
S-Quad Heat sensor states - - - - - - - - - - - - - - - - - - - - - - - - - - 41
S-Quad Dual Optical Heat / Optical Heat sensor states - - - - - - - - - - - - 41
S-Quad Dual Optical Heat CO sensor states - - - - - - - - - - - - - - - - - 42
S-Quad Optical sensor states - - - - - - - - - - - - - - - - - - - - - - - - - 42
Beam sensor states - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 43
How to set 'Zone' label, mode and link to another zone - - - - - - - 44
How to view 'Devices' assigned to a 'Zone' and change device
configuration - - - - - - - - - - - - - - - - - - - - - - - - - - - 44
How 'Cause and Effect' interact with 'Day and Night Modes'- - - - - 45
How to setup zone for 'Immediate Cause and Effect' - - - - - - - - 46
How to setup zone for 'Delayed Cause and Effect'- - - - - - - - - - 46
How to set up 'Day mode' delays and timeout - - - - - - - - - - - - 47
How to set the Calendar - - - - - - - - - - - - - - - - - - - - - - 47
How to manually control Day mode operation - - - - - - - - - - - 48
How to set-up 'Sector' mode, label and activation - - - - - - - - - - 48
How to set-up 4-channel interface devices on the loop- - - - - - - - 49
How to enable/disable a channel of a 4-channel interface device - - - 49
How to view or print device 'Time averages' - - - - - - - - - - - - 50
Time averages explained - - - - - - - - - - - - - - - - - - - - - - - - - - 51
How to view Sensor 'Condition Codes' - - - - - - - - - - - - - - - 52
Condition Codes for S-Quad Sensors - - - - - - - - - - - - - - - - - - - - - 54
How to set up an 'External Evacuate input' - - - - - - - - - - - - - 55
How to set-up the 'Class Change input' - - - - - - - - - - - - - - - 56
How to set up RS-232 and RS-485 serial and USB ports- - - - - - - 57
How to change access levels of 'Buzzer' & 'Device Disablement'- - - 58
4188-949 issue 3_05/10_Nano Comms inst.
How to change the 'Alarm Controls' settings - - - - - - - - - - - - 58
How to change the 'Signal' Settings - - - - - - - - - - - - - - - - 59
How to set up weekly 'Fire test reminder' - - - - - - - - - - - - - - 59
How to start or stop a 'Weekly test' - - - - - - - - - - - - - - - - - 60
How to 'Enable' or 'Disable' a Zone- - - - - - - - - - - - - - - - - 61
How to place a Zone in 'Test Mode' - - - - - - - - - - - - - - - - 61
How to place the system in 'Commissioning mode' - - - - - - - - - 62
How to enable/disable Master alarms, Fire relay and Evac. input- - - 63
How to enable or disable and set a Sector activation control - - - - - 63
How to set up 'Maintenance visit reminder' - - - - - - - - - - - - - 64
How to return 'System Configuration' to factory default settings - - - 64
How to return all 'Labels' to factory default settings - - - - - - - - - 65
How to return the 'Configuration and Labels' to
factory default settings - - - - - - - - - - - - - - - - - - - - - - 65
How to return all 'Access level PIN codes' to factory settings - - - - 66
How to clear all Logs - - - - - - - - - - - - - - - - - - - - - - - 66
How to access the SD card slot on Main Control Board - - - - - - - 67
How to upgrade the panel firmware from a SD card - - - - - - - - - 67
How to back up all system configuration and labels to a SD card- - - 68
How to back up all labels to a SD card - - - - - - - - - - - - - - - 68
How to restore 'Config', 'Labels' or 'Logo' from a SD card - - - - - - 69
How to use a SD card to log 'Historic Events' for diagnostics - - - - 69
Tests on installed equipment - - - - - - - - - - - - - - - - - - - - 70
Appendix A - Message Action List - - - - - - - - - - - - - - - - - 72
Appendix B - General Guidelines - - - - - - - - - - - - - - - - - 77
Appendix C - old Beam sensor - - - - - - - - - - - - - - - - - - - 79
Appendix D - old Mains powered interface unit - - - - - - - - - - 82
Index - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 84
Quick reference menu map - - - - - - - - - - - - - - - - - - - - 86
Nano panel based system
3