Download Print this page

Toshiba SD-C2612 User Manual

Dvd-rom mobile drive.
Hide thumbs

Advertisement

TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-C2612
DVD-ROM MOBILE DRIVE
USER MANUAL

Advertisement

   Related Manuals for Toshiba SD-C2612

   Summary of Contents for Toshiba SD-C2612

  • Page 1

    TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-C2612 DVD-ROM MOBILE DRIVE USER MANUAL...

  • Page 2: Table Of Contents

    CONTENTS Introduction...1 Setup ...3 Using the DVD-ROM ...4 Troubleshooting...6 Specifications ...7 Drive Connectors...10...

  • Page 3: Introduction

    DVD-RW (read, 4.7GB) DVD-RAM (read, 2.6GB, 4.7GB/1.46GB) CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-CD), Multi-session (Photo-CD Disc, CD-Extra, Portfolio, CD-R, CD-RW), CD-R (read), CD-RW (read) Front Panel Figure 1.SD-C2612 DVD-ROM Front Panel...

  • Page 4

    Eject Button The EJECT button is used to open the disc tray so you can install or remove a disc Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur: •...

  • Page 5: Setup

    Toshiba's SD-C2612 drive does not require any unique device drivers for Windows '98/2000/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Win '98/2000/XP/NT Operating Systems support all Toshiba's ATAPI drives natively. If you prefer using DOS, download the ATAPI driver from our web site.

  • Page 6: Using The Dvd-rom

    USING THE DVD-ROM Drive – SD-C2612 Drive Operation Inserting Media – Horizontally or Vertically To insert a DVD in a DVD-ROM drive that is mounted horizontally, perform the following steps: 1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray.

  • Page 7

    The SD-C2612 DVD-ROM/CD-RW drive supports the current RPC phase 2 industry specifications. This means that when the DVD-ROM drive ships from the factory it is set to the region for which the Operating System was intended.

  • Page 8: Troubleshooting

    TROUBLESHOOTING – SD-C2612 Problem Disc tray cannot be opened Drive is not recognized by system Drive is not recognized by system during Boot process, but is recognized by the Operating System (i.e. XP, Win2000, Win98, Win NT, etc.) BUSY Indicator LED flashes...

  • Page 9: Specifications

    SPECIFICATIONS –SD-C2612 General Interface: ATAPI Compatible DVD-ROM Standard - Read DVD: DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD-R (ver 1.0 & 2.0, read) DVD-RW (ver 1.1, read) DVD-RAM (ver 1.0 & 2.1, read) CD-ROM: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD,...

  • Page 10

    Transfer Rate DVD (Single) DVD (Dual) DVD-Video DVD-R/-RW DVD-RAM (Ver 1.0 & 2.1) CD (mode 1) CD (mode 2) Rotational Speed DVD single layer: DVD dual layer: DVD-VIDEO: DVD-R/RW: DVD-RAM (ver 1.0): DVD-RAM (ver 2.1): CD-DA Transfer: CD-RW: IDE Interface Transfer Rates Random Access Time DVD-RAM...

  • Page 11

    DC Voltage and Current Requirements Physical Height Width Depth Weight Connectors IDE Interface Connector Regulatory The SD-C2612 DVD Writeable drive has been certified by the following regulatory agencies: • UL 1950 • CSA C22.2 No. 950 • TUV (EN60950I) •...

  • Page 12: Drive Connectors

    Drive Connectors –SD-C2612 Figure 1.SD-C2612 DVD Writeable Drive Rear Panel – Connector A 50-pin ATAPI interface connector is found at the rear of the SD-C2612 DVD-ROM drive. ATAPI Connecting cable should use Japan Aviation Electronics Industry Limited KX14-50Series L Connector or equivalent connector.

Comments to this Manuals

Symbols: 0
Latest comments: