3CCD CAMERA HEAD
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Your authority to operate this FCC verified equipment could be voided
if you make changes or modifications not expressly approved by the party responsible for compliance
to Part 15 of the FCC rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. For more detailed information about the
take-back and recycling of this product, please contact your supplier where you purchased
the product or consult.
CAUTIONS ON USE
● Please use this apparatus by connecting only with camera control unit IK-TF5U.
● Read the "CAUTIONS ON USE AND INSTALLATION" in the instruction manual of IK-TF5U and follow them.
(1) Camera head (without lens) .............................................................................. 1
(a) Instruction manual ........................................................................................ 1
Rear projection less than 4mm (0.157")
● When connecting the camera cables, be sure to turn off the camera control unit and the other equipment
● We suggest that a c-mount lens designed specially for 3CCD cameras is used.
When using other lens, the best camera performance of this camera may not be obtained.
(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and flare,
ghost or shading may occur)
Furthermore, to avoid damaging the camera, use a lens which has a rear projection from the flange face
of less than 4mm (0.157").
● DC power is supplied by a camera cable model # EXC-TX
model #IK-TF5U (option).
" shows a camera cable type name. Refer to the "Type name" of a camera cable in "OPTIONAL PARTS".
● Refer to the IK-TF5U Instruction Manual section "4.CONNECTION".
Limited Warranty – TOSHIBA CCD Camera
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties
with regard to this CCD Camera ("Product"). These limited warranties extend to the Original End-User ("You[r]").
One (1) Year Limited Warranty of Labor and Parts
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date
of purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does
not perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an
ISD Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the
Product to the ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.
Instruction Manual (Owner's Manual):
You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product. Before seeking
warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and
follow the instructions to correct the problem.
This Limited Warranty is subject to the following conditions:
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance
with specifications during the Limited Warranty period.
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.
4. You must pack the Product in its original carton using the original packing material, then insert the original carton
containing the Product into another carton with additional packing material before shipping the Product to an ASP.
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND
EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL
ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES
IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES
OF ANY KIND, INCLUDING ANY DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR
OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH
OF CONTRACT, TORT OR OTHERWISE, OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO
USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT COMPANY, OR AN ASP HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME
PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
MAY VARY FROM STATE TO STATE.
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO
MISUSE, ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION
OF ISD'S WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED
WITHOUT ISD'S PRIOR AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD'S FACTORY
SERIAL NUMBER. LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT
OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY.
How to Obtain Warranty Service – Step-By-Step Procedures:
To obtain warranty service, You should:
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.
2. Arrange for shipment of the Product to an ASP.
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem
and a copy of the bill of sale or proof of purchase.
4. Prepay all transportation and insurance costs.
Questions? If you have any questions, please check ISD's Web Site or send an e-mail as follows:
Web Site: http://www.toshiba.com/taisisd/indmed
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify,
or extend the terms of this Limited Warranty in any manner whatsoever. The time within which an action must be
commenced to enforce any obligation of ISD arising under this Limited Warranty or under any statute, or law of
the United States or any state thereof, is hereby limited to one (1) year from the date You discover or should have
discovered the problem. This limitation does not apply to implied warranties arising under state law. Some states
do not permit limitation of the time within which You may bring an action beyond the limits provided by state law, so
the above provision may not apply to You. This Limited Warranty gives You specific legal rights and You may also
have other rights which vary from state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division
9740 Irvine Boulevard, Irvine, CA 92618-1697
Copyright © 2007 Toshiba America, Inc. All rights reserved.
This manual is made from 100% recycled paper.
DC IN 12V
DC power supply (option)
(option) through the camera control unit
1/3 inch Progressive CCD
Horizontal : 659, Vertical : 494
F6.8 standard (2000 lx)
Minimum intensity of
14 lx (F2.2, Sensitivity + 18 db)
illumination for objects
C mount (flange back : 17.526 mm in-air)
0ºC to 40ºC (32º F to 104º F)
Less than 90 %
Approx. 65 g (0.143 lbs)
Design and specifications are subject to change without notice.
* For more information, please refer to the section "10. SPECIFICATIONS" in IK-TF5U instruction manual.
For further details, contact your camera dealer.
Camera control unit
Depth 5 [0.2]
Two holes of the top
view are the same as
these two holes.
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the user
in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether intentional or
accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including but not
limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by an
unauthorized third party.
6. Notwithstanding the foregoing, Toshiba's liabilities shall not, in any circumstances, exceed the purchase
price of the product.
COPYRIGHT AND RIGHT OF PORTRAIT
There may be a conflict with the Copyright Law and other laws when a customer uses, displays, distributes,
or exhibits an image picked up by a television camera without permission from the copyright holder. Please
also note that transfer of an image or file covered by copyright is restricted to use within the scope permitted
by the Copyright Law.
PROTECTION OF PERSONAL INFORMATION
Images taken by the camera that reveal the likeness of an individual person may be considered personal
information. To disclose, exhibit or transmit those images over the internet or otherwise, consent of the person
may be required.
LIMITATION OF USAGE
The product is not designed for any "critical applications." "Critical applications" means life support systems,
exhaust or smoke extraction applications, medical applications, commercial aviation, mass transit applications,
military applications, homeland security applications, nuclear facilities or systems or any other applications
where product failure could lead to injury to persons or less of life or catastrophic property damage. Accordingly,
[Toshiba/TAIS] disclaims any and all liability arising out of the use of the product in any critical applications.
CAUTIONS ON USE AND INSTALLATION
● Handling the unit.
Do not drop, jolt, or vibrate, as this may result in damage to the unit. This may cause problems. Treat the camera
cables carefully to prevent cable problems, such as breaks in the cable and loose connections.
● Install the camera in a location free from noise.
If the camera or the cables are located near power utility lines or a TV, etc. undesirable noise may appear on
the screen. In such a case, try to change the location of the camera or the cable wiring.
● Operating ambient temperature and humidity.
Do not use the camera in places where temperature and humidity exceed the specifications. Picture quality
will deteriolate and internal parts may be damaged.
Be particularly careful when using in places exposed to direct sunlight. When shooting in hot places, depending
on the conditions of the object and the camera (for example when the gain is increased), noise in the form of
vertical strips or white dots may occur. This is not a malfunction.
● When not using the camera for extended periods of time.
Switch the control unit off and disconnect the power supply.
● Avoid using or storing the camera in the following places:
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places containing chemicals (such as pesticides), rubber or vinyl products for extended periods of time.
The following descriptions are for that a camera control unit "IK-TF5U" connected to this camera head.
● Do not shoot intense light.
If there is an intense light at a location on the screen such as a spot light, a blooming and smearing may occur.
When intense light enters, vertical stripes may appear on the screen. This is not a malfunction. Ghosts may
occur when there is an intense light near the object. In this case, change the shooting angle.
A moire pattern is an interference pattern generated when two repetitive line patterns overlap. This is not a
malfunction. Eliminating the repetitive line patterns, or aligning the two patterns, will eliminate the moire.
● Handling of the camera head and protection cap.
Keep the camera head and protection cap away from as they may pose a choking hazard. The protection cap
protects the image sensing plane when the lens is removed from the camera head, do not discard.
● When cleaning the camera.
Unplug the power source before cleaning. Clean with a soft dry cloth only. Do not use chemicals or chemically
treated cloths. Chemicals may damage coatings and printed letters. When cleaning the lens, use lens cleaning
● Installation without a tripod.
Before installing the camera head, make sure that the location can withstand the total weight of the camera
head. If this is not the case, reinforce the area to prevent the unit from dropping, which may result in damage
to the unit or personal injury.
Unit : mm [inch]
Depth 3 [0.12]