Doors & Drawer Removal; Remove And Replace Handles; Remove Doors And Hinge; Replace Doors And Hinge - Viking D3 RDFN536D Installation Manual

Doors & Drawer Removal

Remove and Replace Handles

1. Using a 3/32" or 1/8" hex wrench, loosen the
two set screws located on the side of each
handle.
2. Pull the handle straight out from the door.
Make sure you keep the screws for reattaching
the handles.
3. To replace the handles, reverse the directions.
Remove Doors and Hinges
IMPORTANT: Remove food and any adjustable
door or utility bins from doors.
TOOLS NEEDED: 5/16", 3/8", 1/4" hex-head
socket wrench, Torx T20 screwdriver, #2 Phillips
screwdriver, and a flat-blade screwdriver.
1. Unplug refrigerator or disconnect power.
2. Remove the kickplate. Grasp the kickplate
firmly and pull it toward you.
Note: Provide additional support for the
refrigerator door while the hinges are being
removed. DO NOT depend on the door
gasket magnets to hold the door in place while
you are working.
3. Starting with the right-hand side door, remove
the parts for the top hinge as shown in Top
Hinge graphic. Lift the refrigerator door from
the bottom hinge pin.
Note: Remove the hinge pin cover from the
bottom hinge pin and keep for later use. See
Bottom Hinge graphic.
4. Before removing the left-hand side door,
disconnect the wiring plug located on the top
of the top hinge by wedging a flat-blade
screwdriver or fingernail between the two
sections. See Connections graphic.
5. Disconnect the water line by pulling back on
the locking collar while pulling the water line
out of the water line connector. See
Connections graphic.
12
All manuals and user guides at all-guides.com
Remove Doors and Hinges
(cont.)
6. Remove the parts for the top hinge as shown in
Top Hinge graphic. Lift the left-hand side door
from the bottom hinge pin.
Note: Remove the hinge pin cover from the
bottom hinge pin and keep it for later use. See
Bottom Hinge graphic.
Top Hinges
A
B
C
D
A. Hinge Cover Screw
B. Top Hinge Cover
/
5
C. " Hex-Head Hinge Screws
16
D. Top Hinge
Bottom Hinges
A
B
C
A. Hinge Pin Cover
B. Bottom Hinge
C. Hinge Screws
Connections
A
B
A. Wiring Plug
B. Water Line Connection
Door & Drawer Removal
Replace Doors and Hinges
1. Assemble the parts for the top hinge as shown
in Top Hinge graphic. DO NOT tighten the
screws completely.
2. Replace the parts for the bottom hinge as
shown in Bottom Hinge graphic. Tighten
screws. Replace the refrigerator door.
Note: Provide additional support for the
refrigerator door while the hinges are being
moved. DO NOT depend on the door gasket
magnets to hold the door in place while you
are working.
3. Align the door so that the bottom of the
refrigerator door aligns evenly with the top of
the freezer drawer. Tighten all screws.
4. Reconnect the wiring plug on top of the left-
hand side refrigerator door.
5. Reconnect water line by pulling back the
locking collar ring while firmly pushing the
water line into the connector.
6. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to
remove and replace the freezer drawer.
Remove Drawer Front
1. Open the drawer to full extension.
2. Loosen the two top screws attaching the
drawer glides to the drawer front. See Drawer
Front Removal graphic.
Note: Loosen screws three to four turns. Keep
the screws in the drawer front.
3. Remove the two bottom screws attaching the
drawer glide brackets to the drawer front.
4. Lift drawer front upward and off the top screws.
See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the compartment.
Insert the two screws in the drawer front into the
upper slots in the drawer brackets. See Drawer
Front Replacement graphic.
2. Align the drawer glide brackets with the lower
holes in the drawer front and refasten with the
screws. See Drawer Front Replacement graphic.
3. Completely tighten the four screws.
13
(cont.)
Drawer Front Removal
A
B
A. Loosen 2 Drawer Guide Bracket Screws
B. Remove 2 Drawer Glide Bracket Screws
Drawer Front Replacement