Download  Print this page

Causes And Operator Prevention Of Kickback; Safety Guidelines - Definitions - Black & Decker CS1012 Instruction Manual

Black & decker 7-1/4” (185mm) circular saw instruction manual
Hide thumbs

Advertisement

Table of Contents
90511917 CS1012
5/7/07
contact hidden wiring or its own
cord. Contact with a "live" wire will also
make exposed metal parts of the tool
"live" and shock the operator.
• When ripping, always use a rip
fence or straight edge guide. This
improves the accuracy of cut and
reduces the chance for blade binding.
• Always use blades with correct size
and shape (diamond vs. round)
arbor holes. Blades that do not match
the mounting hardware of the saw will
run eccentrically, causing loss of
control.
• Never use damaged or incorrect
blade washers or bolts. The blade
washers and bolt were specially
designed for your saw, for optimum
performance and safety of operation.
CAUSES AND OPERATOR
PREVENTION OF KICKBACK:
• Kickback is a sudden reaction to a
pinched, bound or misaligned saw
blade, causing an uncontrolled saw to
lift up and out of the workpiece toward
the operator.
• When the blade is pinched or bound
tightly by the kerf closing down, the
blade stalls and the motor reaction
drives the unit rapidly back toward the
operator.
• If the blade becomes twisted or
misaligned in the cut, the teeth at the
back edge of the blade can dig into the
top surface of the wood causing the
blade to climb out of the kerf and jump
back toward operator.
• Kickback is the result of tool misuse
and/or incorrect operating procedures
or conditions and can be avoided by
taking proper precautions as given
below.
a. Maintain a firm grip with both
hands on the saw and position
your body and arm to allow you to
resist KICKBACK forces. Kickback
forces can be controlled by the
operator, if proper precautions are
taken.
b. When blade is binding, or when
interrupting a cut for any reason,
release the trigger and hold the
saw motionless in the material
until the blade comes to a
complete stop. Never attempt to
remove the saw from the work or
pull the saw backward while the
blade is in motion or KICKBACK
9:32 AM
Page 4
may occur. Investigate and take
corrective actions to eliminate the
cause of blade binding.
c. When restarting a saw in the
workpiece, center the saw blade
in the kerf and check that the saw
teeth are not engaged into the
material. If saw blade is binding, it
may walk up or KICKBACK from the
workpiece as the saw is restarted.
d. Support large panels to minimize
the risk of blade pinching and
KICKBACK. Large panels tend to
sag under their own weight. Support
must be placed under the panel on
both sides, near the line of cut and
near the edge of the panel.
e. Do not use dull or damaged
blade. Unsharpened or improperly
set blades produce narrow kerf
causing excessive friction, blade
binding, and KICKBACK.
f. Blade depth and bevel adjusting
locking levers must be tight and
secure before making cut. If blade
adjustment shifts while cutting, it
may cause binding and KICKBACK.
g. Use extra caution when making a
"Pocket Cut" into existing walls
or other blind areas. The
protruding blade may cut objects
that can cause KICKBACK.
SAVE THESE INSTRUCTIONS
SAFETY GUIDELINES -
DEFINITIONS
It is important for you to read and
understand this manual. The information
it contains relates to protecting YOUR
SAFETY and PREVENTING
PROBLEMS. The symbols below are
used to help you recognize this
information.
DANGER:
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING:
hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION:
hazardous situation which, if not avoided,
may result in minor or moderate injury.
CAUTION:
alert symbol indicates potentially
4
Indicates an imminently
Indicates a potentially
Indicates a potentially
Used without the safety

Advertisement

Table of Contents
loading

  Related Manuals for Black & Decker CS1012