Download  Print this page

Additional Safety Rules For Scroll Saws - Black & Decker 90527840 Instruction Manual

16 inch (406 mm) variable speed scroll saw with quickset ii blade changing feature
Hide thumbs

Advertisement

Table of Contents
NEVER STAND ON TOOL. Serious injury could occur
18.
if the tool is tipped or if the cutting tool is accidentally
contacted.
CHECK DAMAGED PARTS. Before further use of the
19.
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly
and perform its intended function – check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
DIRECTION OF FEED. Feed work into a blade or
20.
cutter against the direction of rotation of the blade or
cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED.
21.
TURN POWER OFF. Donʼt leave tool until it comes to
a complete stop.
STAY ALERT, WATCH WHAT YOU ARE DOING, AND
22.
USE COMMON SENSE WHEN OPERATING A
POWER TOOL. DO NOT USE TOOL WHILE TIRED
OR UNDER THE INFLUENCE OF DRUGS,
ALCOHOL, OR MEDICATION. A moment of
inattention while operating power tools may result in
serious personal injury.
MAKE SURE TOOL IS DISCONNECTED FROM
23.
POWER SUPPLY while motor is being mounted,
connected or reconnected.
ADDITIONAL SAFETY RULES FOR
WARNING:
READ ALL INSTRUCTIONS BEFORE OPERATING PRODUCT. FAILURE TO FOLLOW ALL INSTRUCTIONS
LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND OR SERIOUS INJURY.
DO NOT OPERATE your scroll saw until it is
1.
completely assembled and installed according to
the instructions.
IF YOU ARE NOT thoroughly familiar with the
2.
operation of Scroll Saws, obtain advice from your
supervisor, instructor or other qualified person.
YOUR SCROLL SAW MUST be securely fastened
3.
to a stand or workbench. If there is any tendency
for the stand or workbench to move during
operation, the stand or workbench MUST be
fastened to the floor.
THIS SCROLL SAW is intended for indoor use
4.
only.
MAKE SURE blade is properly tensioned before
5.
operating saw.
TO AVOID blade breakage ALWAYS adjust blade
6.
tension correctly.
MAKE SURE the blade teeth point downward
7.
toward the table.
NEVER turn the saw "ON" before clearing the table
8.
of all objects (tools, scraps of wood, etc.).
DO NOT cut material that is too small to be safely
9.
supported.
AVOID awkward hand positions where a sudden
10.
slip could cause a hand to move into the blade.
ALWAYS keep hands and fingers away from blade.
11.
ALWAYS adjust holddown foot for each new
12.
operation.
DO NOT USE dull or bent blades.
13.
DO NOT attempt to saw material that does not
14.
have a flat surface, unless a suitable support is
used.
24.
25.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.
Refer to them often and use them to instruct others.
SCROLL SAWS
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
3
THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always
operate machinery in well ventilated areas and provide
for proper dust removal. Use wood dust collection
systems whenever possible.
SOME DUST CREATED BY POWER SANDING,
SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals
known to cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other
masonry products, and
· arsenic and chromium from chemically-treated
lumber.
SAVE THESE INSTRUCTIONS.
MAKE "relief" cuts before cutting long curves.
NEVER attempt to cut a curve that is too tight for
the blade being used.
WHEN backing a blade out of a workpiece, the
blade may bind in the saw kerf. This is usually
caused by sawdust in the kerf. If this happens, turn
"OFF" the switch and remove plug from power
source outlet. Wedge open the kerf and back
blade out of the workpiece.
THE USE of attachments and accessories not
recommended by Black & Decker may result in the
risk of injuries.
ALWAYS hold the work firmly against the table.
DO NOT feed the material too fast while cutting.
Only feed the material fast enough so that the
blade will cut.
NEVER start the Scroll Saw with the stock pressed
against the blade.
WHEN cutting a large workpiece MAKE SURE the
material is supported at table height.
USE CAUTION when cutting material which is
irregular in cross section which could pinch the
blade before the cut is completed. A piece of
moulding for example must lay flat on the table
and not be permitted to rock while being cut.
USE CAUTION when cutting round material such
as dowel rods or tubing. They have a tendency to
roll while being cut causing the blade to "bite." Use
a V-block to control the piece.
ALWAYS release blade tension before removing
the blade from the upper or lower blade holders.
MAKE CERTAIN table tilting lock is tightened
before starting the machine.

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for Black & Decker 90527840

This manual is also suitable for:

Bdss100