Advertisement
Quick Links
Advertisement
Summary of Contents for Tiger Shark Shark
- Page 1 Owner’s Manual...
- Page 2 Important Note To Parents About Safe Riding Your child's safety will depend on your commitment to always provide a safe riding environment and a properly maintained vehicle. As with any moving vehicle there are possible safety risks; be sure to heed to the following precautions. 1.
- Page 3 Safety Precautions Review all the instructions carefully before operations. Follow all rules and regulations in your area for operating an electric scooter. Do not allow others to use the scooter without proper instructions. Ride only in good weather, on smooth surfaces. Remember to always operate your scooter with the proper safety gear and helmet.
- Page 4 List of Parts Handle Bar Grips Front Fork Front Wheel Power Switch Kickstand Skid Plate Rear Wheel Deck Quick Release Hand Brake Throttle Controller Batteries 600W Motor Brake Pad Charger Chain Tubes Shocks Tool Kit...
- Page 5 Assembly Instructions Carefully take your scooter out of the box. Assemble the Handle Bar. Remove the bolt from the base of the Handle Bar and position the top part of the Handle Bar on to the base and tighten the bolt. Lift Handle Bar into upright position and tighten star screw.
- Page 6 Unscrew the bolts on the ‘T’ of the Handle Bar and place the Grips into the Handle Bar and screw in the bolts to secure the grips. Turn the Power Switch to the on position. A red light will appear. Before operating your scooter check the following to make sure they are secure and intact: Tires Check for wear, that the bolts are securely fastened, tire pressure is 85 PSI,...
- Page 7 Charging Power Switch must be in the ‘off’ position. Do not plug the charger into the outlet first, for safety reasons plug the charger cord into the scooter first, then into a 110 V outlet. Charge your scooter for 6-8 hours. The LED will be red during charging and once it is fully complete the LED will turn to green.
- Page 8 Change the Rear Tire • Tools Required: - Phillips screwdriver - 8mm wrench - 2 x 16mm wrench Step Description Ensure power switch is in the "off" position before beginning any work on the scooter. Remove screw holding brake shield in place located next to the left side of the rear tire. This bolt connects the brake shield to the frame.
- Page 9 Step Description Remove the deck. Disconnect the wires, by loosening the bolts. Unscrew the 2 bolts that secure the motor, as pictured below, and remove the motor. Change the Motor...
- Page 10 Step Description Loosen axle bolt. To tighten chain, turn the 8mm nut on the eyebolt counter clockwise To loosen the chain, turn the 8mm nut on the eyebolt clockwise. Adjust the Chain...
- Page 11 Adjust the Brake Step Description Tighten Loosen nut; loosen the 8mm nut and pull the cable back and slide the arm forward, once you have the Brake cable in position tighten the 8mm nut. Loosen Loosen nut; loosen the 8mm nut and the spring will pull the cable back, once you have the cable in Brake position tighten the 8mm nut.
-
Page 12: Troubleshooting Chart
Problem The power light by the on/off switch does not light up when the scooter is turned on? The power lights by the on/off switch light up when scooter still does not work? Clicking noise coming from motor? When the Brake Lever is squeezed my scooter does not stop? My scooter is going slower, and... - Page 13 YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT...
- Page 14 Warranty. Rad2Go warrants each new Rad2Go product for thirty (30) days according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of the original retail purchase. Any part of the Rad2Go Product manufacture or supplied by Rad2Go and found in the reasonable judgment of Rad2Go to be defective in material or workmanship will be repaired or replaced by an authorized Rad2Go service dealer without charge for parts and labor.
- Page 15 This Warranty Registration is to be completed by the dealer or customer at the time of purchase and submitted to Rad2Go, Inc., within 10 days of the date of purchase for warranty entitlement. This warranty is void if the serial number or the safety warning labels on your Rad2Go Electric Scooter are altered, defaced, or removed.
- Page 16 nature and any circumstances leading to the problem. A service technician will contact you with specific instructions to ensure that you receive the best service for your scooter in the most economical way. Purchaser herewith acknowledges: That Rad2Go assumes not liability for any misuse or improper operation of Rad2Go Electric Scooters or Vehicles.
- Page 17 BY SIGNING BELOW YOU ARE AGREEING TO HAVE ANY DISPUTES ARISING OUT OF THE MATTER INCLUDING IN THE “ARBITRATION OF DISPUTES” PROVISION DECIDED BY NEUTRAL, BINDING ARBITRATION AS PROVIDED BY CALIFORNIA LAW, AND THAT YOU ARE GIVING UP THE RIGHTS YOU MIGHT POSSESS TO HAVE THE DISPUTE LITIGATED IN A COURT OR JURY TRIAL.