Kärcher SE 4001 Plus Manual page 9
Hide thumbs
Also See for SE 4001 Plus:
- Original instructions manual (146 pages) ,
- Manual (190 pages) ,
- Instruction manual (9 pages)
Table of Contents
Advertisement
Available languages
Available languages
Fill up fresh water reservoir
Note: You can remove the water reservoir to fill it or you
can fill it directly on the appliance.
Illustration
Flip the reservoir cover up.
Add 100 - 200 ml (volume depends on degree of
contamination) of RM 519 into the fresh water res-
ervoir, then add tap water - do not overfill.
Close the reservoir cover.
Start working
Illustration
Insert the mains plug into the socket.
Press the switch for suction (position I), suction tur-
bine is running.
Illustration
Close fully the surrounding air separator at the han-
dle.
Illustration
Press the switch for spraying (position I), the deter-
gent pump is ready.
Use the lever on the spray handle to spray on de-
tergent solution.
Run across the surface to be cleaned in overlap-
ping paths. Pull the nozzle backwards (do not
push).
Emptying the reservoir during operation
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
Switch the appliance off by pressing the switch for
suction and spraying (position 0).
Remove the accessories and the fresh water reser-
voir and unlatch the motor casing.
Remove the motor casing and empty the reservoir.
Cleaning tips/mode of operation
–
Always work from the light to the shade (from the
window to the door).
–
Always work from the cleaned to the uncleaned
surface.
–
Rugs with jute backing can shrink if too much water
is used and can bleed colours.
–
Brush high-fiber rugs in the direction of the weave
after cleaning (using a fiber brush or a scrubber).
–
Water-proofing the fabric using Care Tex RM 762
after the wet cleaning prevents a quick resoiling of
the textile surface.
–
Do not step on cleaned surfaces until they have
dried and do not place furniture on them to avoid
pressure spots or rust stains.
Cleaning methods
Light/normal contamination
Turn on suction and spraying (position I).
Spray and simultaneously suction off detergent so-
lution in one work cycle.
Switch off the spray switch and suction off the re-
maining cleaning solution.
After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
Heavy soiling or stains
Switch on sprayer (position I).
Apply detergent solution and soak for 10 to 15 min-
utes (suction is switched off).
Clean the surface just like you would with light/nor-
mal soiling.
After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
End wet cleaning process
Rinse the spray tubes in the appliance as follows:
Fill the detergent container with about 1 liter of
clear water.
Hold the nozzle above the drain, and switch on the
spraying pump until the clear water has been con-
sumed.
Use as multi-purpose vacuum cleaner
Note
To use the device as a multi-purpose vacuum cleaner,
the spray handle and the spray hose can be removed.
Illustration
Remove the spray hoses and mounting clips from
the suction hose and suction tubes.
Press the two locking noses on the sides and pull
the spray handle off the handle.
ATTENTION
Always work with the filter bag inserted during dry vac-
uum cleaning, except when a cartridge filter is used
(special accessory). Container and accessories must
be dry, otherwise dirt may adhere.
Select the desired accessories and attach to the
suction pipes or directly to the handle.
Illustration
Insert a filter bag.
Select the desired accessories and attach to the
suction pipes or directly to the handle.
Switch on suction (position I).
Vacuuming hard surfaces
Insert the hard surface inlay into the floor nozzle.
The bristles should point towards the front.
Vacuuming carpeted floors
Work without the hard surface insert.
Illustration
Use the surrounding air separator to adapt the suc-
tion force.
Note:
Close the surrounding air separator again after
use!
Vacuuming up water
ATTENTION
Do not use a filter bag!
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
Attach the accessories to vacuum moisture or wet-
ness to the suction tubes or directly to the handle.
Switch on suction (position I).
Illustration
Open the sliding air regulator when vacuuming up
larger quantities of water. Close it again after use.
Empty the full reservoir (refer to chapter "Empty
reservoir").
– 9
Page 16
- Quick Links:
- Start up
Hide quick links:
Advertisement
Chapters
Table of Contents
