Download Print this page

Black & Decker VP800 Instruction Manual page 7

3.6 volt 3 position pivot screwdriver

Advertisement

Available languages

Available languages

90502289 - VP800 Scre
Operating Instructions
REMOVING AND INSTALLING BITS
To install a bit simply insert it into the cavity in the spindle. To remove bit, pull straight out.
REMOVING AND INSTALLING THE BATTERY
NOTE: VERSAPAK™ BATTERIES ARE NOT FULLY CHARGED AT THE FACTORY.
To install the battery into the tool, slide it into the handle until it clicks into place.
To remove the VersaPak™ battery from the tool, press the release button, (Fig. 3), and pull
the battery out of the tool.
NOTE: Battery caps are provided for use when carrying batteries or while battery is stored
in a pocket, tool box, etc. Remove cap before placing battery in charger or tool.
Install the battery cap, (Fig. 2), by snapping it in place. To remove the cap, simply pull it off.
SWITCH
To turn the tool ON in a forward direction, press the top section of the rocker switch and
the tool will run. To operate in reverse, press the bottom section of the rocker switch and
the tool will run. Without depressing the rocker switch the tool is locked and will act as any
conventional, non-powered screwdriver.
TORQUE CONTROL
Your screwdriver is equipped with an adjustable clutch control feature. When the tool
reaches the preselected torque setting the clutch slips, thus limiting how tightly a screw is
driven.
NOTE: The tool's motor will continue to run as long as the switch button is depressed.
To set the tool's torque, rotate the adjustable clutch collar (Fig. 3) clockwise or
counterclockwise as required. The higher the number, the higher the torque. Each click in
a clockwise direction (facing the spindle) means an increase in the torque produced.
TWO POSITION SCREWDRIVER
To convert the tool to an angled screwdriver pull back on the release button shown in Fig.
4 and rotate the top portion of the tool as shown in Figures 5 and 6.
TWO POSITION SCREWDRIVER WARNINGS:
• To avoid being pinched, hold the screwdriver as shown in Figures 5 and 6 when changing
positions.
• Do not use screwdriver as a pry bar in either position.
• To avoid screwdriver being turned on accidentally, do not carry in your pocket.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this manual) should be performed by authorized
service centers or other qualified service personnel, always using identical replacement
parts.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING:
The use of any accessory not recommended for use with this tool could be
hazardous.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the costs
to recycle the battery (or battery pack) at the end of its useful life have already
been paid by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium
batteries in the trash or municipal solid waste stream and the RBRC program provides an
environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural resources by
returning the spent nickel-cadmium battery to an authorized Black & Decker service
center or to your local retailer for recycling. You may also contact your local recycling
center for information on where to drop off the spent battery, or call 1-800-BATTERY.
5/10/06
2:27 PM
Page 7
7

Advertisement

loading
Save PDF