1. Manuals
  2. Brands
  3. Therma-Stor Manuals
  4. Fan
  5. Phoenix TS-285
  6. Installation, operation & service instructions

Therma-Stor Phoenix TS-285 Installation, Operation & Service Instructions

Phoenix axial air mover
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual — Phoenix Axial Air Mover
The Phoenix Axial Air Mover is the industry's only Air Mover specifically engineered with patent pending
FOCUS
Technology. FOCUS
TM
greater than competitive product offerings. This highly focused air flow is directed towards the restoration
industry's problematic drying areas namely, carpet and pad, sub-floor, sill plate and walls. No other fan
dries the sill plate as quickly! Finally, the Phoenix Axial Air Mover with FOCUS
air velocities further than any other Axial Air Mover.
The Phoenix Axial Air Mover includes a 2-speed motor delivering a focused
airstream of approximately 3000 cfm, lightweight stackable
enclosure designed to fit existing vehicle rigging, on-board duplex
GFCI outlet, circuit breaker, superior cord management and hour
meter.
Conventional air movers create a circular air jet. With a circular
air jet the only way to get air into the square corner is to point
the fan towards the corner. This angle toward the wall wastes
valuable air velocity and throw distance. FOCUS
creates an air jet with a square corner, resulting in optimized
drying ability. In addition, the Axial Air Mover features built in
4.5° positioning which increases the fans ability to dry.
Dry fast, smart and profitably with Phoenix.
Phoenix Axial Air Mover
• Approximately 3000 CFM air flow directed where
you need it.
• Operator interface conveniently located for easy
access, featuring: power indicator lamp, large three-
position switch, circuit breaker, GFCI outlet, and
hour meter.
• Daisy-chain up to four Phoenix Axial Air Movers on a
single circuit.
• Integral circuit breaker eliminates nuisance trips to
the breaker box.
• Axial Air Mover itself is also GFCI protected.
• Units interlock for ease of stacking during storage
and handling.
• Weighs 2.5 lbs less than competitive units.
• Linear low density polyethylene construction.
• Low bearing temperatures increase motor life.
• Permawick®, low maintenance, long life lubrication.
Specifications subject to change without notice.
Toll-Free -800-533-7533
PO Box 8680 • Madison, WI 53708
Installation, Operation & Service Instructions
Read and Save These Instructions
Technology revolutionizes evaporative drying by producing air velocities
TM
Technology
TM
Technology sustains these
TM
Phoenix Axial Air Mover
PN 4025200

www.thermastor.com • sales@thermastor.com
Phoenix Axial Air Mover
TS-285
Revised 1/07

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Phoenix TS-285 and is the answer not in the manual?

Questions and answers

Related Manuals for Therma-Stor Phoenix TS-285

Summary of Contents for Therma-Stor Phoenix TS-285

  • Page 1 • Permawick®, low maintenance, long life lubrication. Specifications subject to change without notice. Toll-Free -800-533-7533 PO Box 8680 • Madison, WI 53708 Technology sustains these Technology Phoenix Axial Air Mover PN 4025200 Phoenix Axial Air Mover TS-285 Revised 1/07 www.thermastor.com • sales@thermastor.com...

  • Page 2: Table Of Contents

    Table of Contents Introduction ... FOCUS Technology Features and Benefits ... 1. Safety Information ...2 2. Intended Application ...3 3. Safety Certifications ...3 4. Specifications ...3 5. Power Requirements ...3 5. Daisy-Chaining ...3 5.2 Recommended Use ...3 5.3 Integrated Cord Wrap ...4 6.

  • Page 3: Intended Application

    • Vérifier la protection du différentiel avant chaque utilisation en appuyant sur le bouton “ test “. Si l’appareil fonctionne correctement, le bouton “ reset “ ressort. • Avant de laisser un appareil aéraulique axial sans surveillance, s’assurer que les enfants n’ont pas accès à...

  • Page 4: Integrated Cord Wrap

    55.3 Integrated Cord Wrap The Phoenix Axial Air Mover features integrated cord management. Wrap the cord around the cord wrap as shown and secure the cord with the clasp on the plug. Figure 3: Cord wrap 6 Applications 6.1 Sizing for Water Restoration Jobs Current industry standards call for one air mover per 0-6 linear feet of wall space, dependent upon the Class of wa- ter damage.

  • Page 5: Orientation Of Directional Drying

    Making use of factory installed feet (4) Counter clockwise airflow pattern Figure 7: Birds eye view of room set-up User installed feet for use during clockwise drying set-ups Factory installed feet for use during counter clockwise drying Figure 8: Clockwise feet locations If the water restoration professional dries in the clockwise direction often, we suggest attaching the two (factory provided) rubber feet into the threaded holes on the side...

  • Page 6: Power Indication Lamp

    the device’s power cord. Should an over-current condition occur, the Axial Air Movers’ on-board circuit breaker prevents nuisance visits to a remote power junction box. IMPORTANT: Total amperage of the Axial Air Mover plus all devices plugged into the receptacle must not exceed 12 amps.

  • Page 7: Motor Lubrication

    9.2 Motor Lubrication Oil the unit every six months with 3 - 4 drops of SAE 20 weight non-detergent oil. Lubricate the motor with a drop of oil after each washing. IMPORTANT: The approved oil for lubrication is SAE 20 weight non-detergent oil, specifically designated for use with electric motors.
  • Page 8 This page intentionally left blank. Toll-Free 1-800-533-7533 www.thermastor.com • sales@thermastor.com...

  • Page 9: Warranty

    Phoenix Axial Air Mover Limited Warranty Warrantor: Therma-Stor LLC PO Box 8680 Madison, WI 53708 Telephone: -800-533-7533 Who Is Covered: This warranty covers Phoenix Axial Air Movers. First Year Warranty: 00% parts and labor (all components) Second Year Warranty: 00% parts only (all components) Years Three through Seven: Only materials and workmanship of the housing are covered.

Table of Contents