Table of Contents
Advertisement
Quick Links
Owner's Manual — Phoenix Mini-Guardian
The Phoenix Mini-Guardian HEPA System is the compact, variable
air speed version of our popular Phoenix Guardian HEPA System.
Maximum delivered air flow with 3-stage filtering in place is over
45 CFM and will clean one air change of a 4 x 4 foot room in
less than four minutes while drawing less than two amps of power.
This makes the Mini-Guardian HEPA System perfect for smaller
remediation projects where space is at a premium and reduced air
flow essential. A template on the intake grill makes it possible to
take air-flow measurements with the Phoenix Kestrel 3000 Multi-
Meter.
The Mini-Guardian HEPA System's 3-stage filter design with true
HEPA filtration will remove virtually all hazardous particles from
the air and an optional fourth stage filter of activated carbon
and potassium permanganate will absorb a wide range of odors
and gases. The unique 24" canister HEPA, manufactured for the
Phoenix Mini-Guardian HEPA System, contains nearly 200 square
feet of surface area. This allows maximum air-flow and significantly
extends filter life.
The Phoenix Mini-Guardian HEPA System
• Less than 2 amps
• Compact design
• Variable speed flow
• Multiple ducting options
• Stainless steel cabinet
• Optional fourth stage carbon filter
• Wheeled cart design
Specifications subject to change without notice.
Toll-Free 1-800-533-7533
PO Box 8680 • Madison, WI 53708
HEPA System
Installation, Operation & Service Instructions
Read and Save These Instructions
Phoenix Mini-Guardian HEPA System
PN 4024774
www.thermastor.com • sales@thermastor.com
Phoenix Mini-Guardian HEPA System
TS-261B
Revised 1/07
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Therma-Stor TS-261B
- Page 1 • Optional fourth stage carbon filter • Wheeled cart design Specifications subject to change without notice. Toll-Free 1-800-533-7533 PO Box 8680 • Madison, WI 53708 HEPA System Phoenix Mini-Guardian HEPA System PN 4024774 Phoenix Mini-Guardian HEPA System www.thermastor.com • sales@thermastor.com TS-261B Revised 1/07...
-
Page 2: Table Of Contents
Table of Contents Introduction ... 1. Specifications ... 2. Operation ... 2. Handle Assembly Procedure ... 2.2 Transporting the Phoenix Mini-Guardian HEPA System ...2 2.3 Location ...2 2.4 Electrical Requirements ...3 2.5 Air Ducting ...3 2.5A Inlet Ducting ...3 2.5B Outlet Ducting ...3 2.6 Negative Air Ducting ...4 2.7 Power Switch ...4 2.8 Hour Meter ...5... -
Page 3: System
2. Locate the two mounting holes for the handle assembly on the Mini-Guardian HEPA System cabinet. They are located in close proximity to the top of the cabinet near the corners. A lock nut should be visible through each of the mounting holes and is held in place by a retainer plate secured to the cabinet shell. -
Page 4: Air Ducting
2.5 Air Ducting 2.5A Inlet Ducting Occasionally the area to be filtered is difficult to access and/or the unit cannot be located in the area. In such cases, the air can be ducted to the unit’s inlet. A round 2” diameter flexible duct can be attached to the unit inlet on top. -
Page 5: Hour Meter
CAUTION: Do not remove the top to access the filters with the unit on. Removing the top and filters while running can: (A) expose potentially fatal high voltage electrical parts, and (B) expose the dangerous rotating impeller fan. 2.8 Hour Meter A digital hour meter is located near the power/speed control on the unit front. - Page 6 Airflow on high speed with all filters clean and no ducting is about 400 CFM. The unit can be run with very dirty filters and virtually no flow without harming the unit. The operator’s decision to change filters should be based on filter cost vs.
-
Page 7: Service
4 Service CAUTION: Servicing the Phoenix Mini-Guardian HEPA System with its high voltage circuitry presents a health hazard that could result in death, serious bodily injury, and/ or property damage. Only qualified service people should service this unit. 4.1 Warranty A warranty certificate has been enclosed with this unit. - Page 8 8. Using a pliers, twist the tabs of the base supports to align with the slots. Remove only one of the base supports (see below). Spread the base apart slightly to remove the impeller fan. Twist tabs Figure 16: Twist tabs Toll-Free 1-800-533-7533 9.
-
Page 9: Service Parts
5 Service Parts Item Part No. Qty. Description 4024824 Air Filter, Polyester, ” x 6” x 6” 402799 Air Filter, Pleated, 2” x 6” x 6” 4024667 Air Filter, HEPA, 4” OD x 24” (99.97% Efficient) 4024830 Axle 4024684 Impeller Fan 4024773 Impeller Fan Speed Control 4024825... - Page 10 This page intentionally left blank. Toll-Free 1-800-533-7533 www.thermastor.com • sales@thermastor.com...
- Page 11 Phoenix Mini-Guardian HEPA System Limited Warranty Warrantor: Therma-Stor LLC PO Box 8680 Madison, WI 53708 Telephone: -800-533-7533 Who Is Covered: This warranty extends only to the original end-user of the Mini-Guardian HEPA System, and may not be assigned or transferred. First Year Warranty: Therma-Stor Products warrants that, for one () year the Mini-Guardian HEPA System will operate free from any defects in materials and workmanship, or Therma-Stor Products will, at its option, repair or replace the defective part(s), free of any charge.
Need help?
Do you have a question about the TS-261B and is the answer not in the manual?
Questions and answers