Subscribe to Our Youtube Channel
Related Manuals for SOMFY Pergola sc io
Summary of Contents for SOMFY Pergola sc io
- Page 1 Pergola sc io Notice installateur Insallationsanleitung Guida all’installazione Montagehandleiding Installation guide Guía de instalación Guia de instalação Tesisatçı Kılavuzu...
-
Page 2: Table Of Contents
5.6. Checking the settings 1. INTRODUCTION The Pergola sc io motor is designed to drive all vertical blinds used on terraces with or without a manual latch (with or without fabric tension). What is io-homecontrol®? The Pergola sc io uses io-homecontrol®, the new universal and secure wireless communication protocol, shared by the major manufacturers in the world of home automation. -
Page 3: Safety
Any use outside the area of application specified by Somfy is prohibited. This invalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein. Never begin installing without first checking the compatibility of this product with the associated equipment and accessories. -
Page 4: Motor/Tube Assembly
3 x 0.75 mm 230 V table below: 50 Hz 3 x 1.5 mm 230 V ~ 50 Hz Motor cable 1 Brown Live (P) 2 Blue Neutral (N) 3 Yellow/Green Earth ( ) Copyright © 2010 Somfy SAS. All rights reserved. -
Page 5: Commissioning
Pergola sc io 5. COMMISSIONING The guide only describes commissioning using a Situo io type Somfy io local control point. For commissioning using any other io control point, refer to the corresponding guide. 5.1. Identifying setting steps already completed Only one motor should be powered at a time. -
Page 6: Setting The End Limits
Press the "my" button again until the blind moves briefly: the end limits have been programmed. Go to the section "Programming the first Somfy io local control point". 5.4.2. Manually setting the end limits on vertical blinds For vertical blinds without a cassette, the upper and lower end limits must be set. -
Page 7: Programming The First Somfy Io Local Control Point
PROG. H 5.6. Checking the settings Check the settings of the upper and lower end limits using the Somfy io local control point. 6. OPERATION 6.1. Standard operation 6.1.1. Up and Down buttons Briefly press the Up or Down button to raise or lower the blind... -
Page 8: Additional Settings
The motor is factory set at the medium level. For safety reasons, this function can only be accessed via the Somfy io control point in 3 scenarios: • After validation of the settings and before programming the first Somfy io control point. -
Page 9: Tips And Recommendations
(high/medium/low). The motor's default factory setting is the low level. For safety reasons, this function can only be accessed via the Somfy io control point in 3 scenarios: • After validation of the settings and before programming the first Somfy io control point. -
Page 10: Replacing A Lost Or Broken Somfy Io Control Point
Pergola sc io 8.2. Replacing a lost or broken Somfy io control point Refer to the corresponding guide. 8.3. Restoring the original configuration This reset deletes all control points, all the sensors and all the end limit settings, and resets the motor's direction of rotation and favourite position (my). - Page 11 Pergola sc io Copyright © 2010 Somfy SAS. All rights reserved.
- Page 12 Tel: +39-024847181 Tel. +351 229 396 840 United Arab Emirates: Czech Republic: Japan: Romania: Somfy Gulf Jebel Ali Free Zone Somfy, spol. s.r.o. SOMFY KK Somfy SRL Tel: +971 (0) 4 88 32 808 Tel: (+420) 267 913 076 - 8 Tel: +81 (0)45 481 6800 Tel.: +40 - (0)368 - 444 081...
Need help?
Do you have a question about the Pergola sc io and is the answer not in the manual?
Questions and answers