Related Manuals for Telex 80
Summary of Contents for Telex 80
- Page 1 Application Guide Kenwood Radio Series 80, 90 and 150/180 To IP-223 November 4, 2005 P/N AN-VEGA-1 Rev D...
-
Page 2: Table Of Contents
Table of Contents 1 General ... 1 2 Setup ... 1 TK-x150/180 Model Cable Assembly:... 1 TK-x80 Model Cable Assembly: ... 1 2.2.1 IP223 Rev F or higher Board Configuration: ... 2 2.2.2 IP223 Rev A to Rev E Board Modifications: ... 2 TK-x90 Model Cable Assembly: ... -
Page 3: General
IP-223 to Kenwood Radios 1 General The application note is intended to show how to assemble the cable and setup the hardware of the IP223 for channel change and FleetSync applications using Kenwood radio. 2 Setup 2.1 TK-x150/180 Model Cable Assembly: NOTE: There are differences between the TK-x150 and TK-x180 radios DB25 connectors. -
Page 4: Ip223 Rev F Or Higher Board Configuration
2.2.1 IP223 Rev F or higher Board Configuration: Set the jumper J35 to B position for line 1 and the jumper J26 to B position for line 2 IP223 Serial Signal 2.2.2 IP223 Rev A to Rev E Board Modifications: Lift Pin 12(line 1) or pin 9(line 2) of U45 according to the line selected and solder to its PCB Pad. -
Page 5: Ip223 Rev A To Rev E Board Modifications
IP-223 to Kenwood Radios 2.3.2 IP223 Rev A to Rev E Board Modifications: Lift Pin 12(line 1) or pin 9(line 2) of U45 according to the line selected and solder to its PCB Pad. Please refer to the Figure 1 for better demonstration. IP223 Serial Signal Pin on U45 of the board... -
Page 6: Ip223 Configuration
2.4 IP223 Configuration: Setup the desired IP223 line for Kenwood radio control at the following screen: 2.4.1 Per-line setup screen Choose radio model in the Serial Port Mode box (A). Change Serial Port Parameter box to 9600.N.8.2 (B). Configure Talk Group and CHAN fields for channel change capability (C ). 2.4.2 IP223 Jumper settings Line 1 J33, J34... -
Page 7: Radio Configuration
IP-223 to Kenwood Radios 2.5 Radio Configuration 2.5.1 TK-x80 Series Program Com 1 for DATA... -
Page 8: Tk-X90 Series
IP-223 to Kenwood Radios 2.5.2 TK-x90 Series Program Function Port, Input screen for Ext PTT in Radio 1 Al1. - Page 9 IP-223 to Kenwood Radios Program Function Port, Output screen for COR in Radio 1 AO1.
-
Page 10: Tk-X150/180 Series
IP-223 to Kenwood Radios 2.5.3 TK-x150/180 Series Program Function Port, Aux Input for External PTT in AUX Input4 location and COR in AUX Output1. Program Com 1 for DATA... - Page 11 : vega@telex.com note, by fax (402-467-3279) or e-mail them to Technical Support: Email address: acttechsupport@us.telex.com Phone #: 1-800-898-6723 TELEX Communications, Inc Vega Signaling Products 8601 East Cornhusker Highway, Lincoln, Nebraska, 68507 Phone: (800) 752-7560 Fax: (402) 467-3279 E-mail: vega@telex.com, Web: www.vega-signaling.com...
Need help?
Do you have a question about the 80 and is the answer not in the manual?
Questions and answers